J1939 · Aftertreatment - DPF
SPN 3242 Fault Code
Aftertreatment 1 diesel particulate filter intake gas temperature
What does SPN 3242 mean?
Exhaust temperature entering the DPF, read by a sensor at the filter inlet. The ECM uses it to manage regeneration and to protect the filter from overheating. How urgent it is depends on the FMI after SPN 3242 - pick it below. Check first: compare this sensor with the DOC intake and DPF outlet readings after a cold soak; all three should agree.
- SPN 3242
- Aftertreatment 1 diesel particulate filter intake gas temperature
- FMI ?
- How it failed - the number after the SPN
Can I keep running with it?
Depends on the FMI
How urgent it is depends on the FMI after SPN 3242 - pick it below.
What should I check first?
Compare this sensor with the DOC intake and DPF outlet readings after a cold soak; all three should agree
Then 4 more checksWhere to read it
Connect a J1939-capable scan tool to the 9-pin diagnostic port.
Which FMI shows after SPN 3242?
You'll notice: The ECM loses the gas temperature entering the particulate filter, so it cannot manage a regeneration safely.
Find the number shown after SPN 3242 on your display. 2 of them have their own page with causes and checks.
- 0SPN 3242 FMI 0: Value is above the normal range, most severe levelReal conditionCummins ISX15
- 2SPN 3242 FMI 2: Data is erratic, intermittent or incorrectErratic or implausibleCummins ISX15
- 3SPN 3242 FMI 3: Signal voltage is above normal, or the circuit is shorted to a high sourceShorted highCummins ISX15, Detroit DD15, Detroit DD13, Detroit DD13 Gen 5 and 1 more
- 4SPN 3242 FMI 4: Signal voltage is below normal, or the circuit is shorted to a low sourceShorted lowCummins ISX15, Detroit DD15, Detroit DD13, Detroit DD13 Gen 5 and 1 more
- 7SPN 3242 FMI 7: Temperature sensor is not respondingPart or controllerDetroit DD15
- 8SPN 3242 FMI 8: Temperature signal shows a spikeErratic or implausibleDetroit DD15, Detroit DD13, Detroit DD13 Gen 5, Detroit DD15 Gen 5
- 15SPN 3242 FMI 15: Value is above the normal range, least severe levelReal conditionCummins ISX15
- 16SPN 3242 FMI 16: Value is above the normal range, moderately severe levelReal conditionCummins ISX15
- 17SPN 3242 FMI 17: Inlet temperature is too low to allow hydrocarbon dosing, least severeReal conditionDetroit DD15, Detroit DD13, Detroit DD13 Gen 5, Detroit DD15 Gen 5
- 18SPN 3242 FMI 18: Inlet temperature is too low to allow hydrocarbon dosing, moderately severeReal conditionDetroit DD13 Gen 5, Detroit DD15 Gen 5
- 20SPN 3242 FMI 20: Inlet and outlet temperature sensors disagree, with the inlet reading high or the outlet lowErratic or implausibleDetroit DD15, Detroit DD13, Detroit DD13 Gen 5, Detroit DD15 Gen 5
Checks
0 of 5 done
When to stop
Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.
How urgent SPN 3242 is depends on its FMI and whether the engine has derated. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Causes
- Reads cold: an open circuit or a short to supply in the DPF intake temperature sensor wiring, which the ECM reads as an extremely low temperature
- Reads hot: signal wire shorted to ground or the DPF intake temperature sensor element shorted, which the ECM reads as an extremely high temperature
- Real condition: hydrocarbon doser or in-cylinder dosing fault that leaves the gas cooler than commanded between the DOC and DPF
- Real condition: cracked or leaking canister joint between the DOC and DPF
1 more causeFewer causes
- Sensor: soot build-up coating the sensor tip, so readings lag the true gas temperature
Other Aftertreatment - DPF codes
Source
Cummins ISX15 2013-2018 fault codes list (Diesel Laptops)
This list names SPN 3242 and the FMIs above for the engines it covers. The guidance on this page is general, not taken from it.
The source covers: Cummins ISX15 (2013-2018) and X15; same SPN on other J1939 engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
