EF Logo

J1939 · Aftertreatment - DPF

SPN 3483 Fault Code

Aftertreatment 1 regeneration status

What does SPN 3483 mean?

The present state of DPF regeneration: idle, active or in progress. The ECM broadcasts it so the dash and other modules know a regeneration is under way. How urgent it is depends on the FMI after SPN 3483 - pick it below. Check first: read other stored aftertreatment faults first, since they usually block regeneration.

FaultActiveSPN 3483FMI --J1939 engine ECU
SPN 3483
Aftertreatment 1 regeneration status
FMI ?
How it failed - the number after the SPN

Can I keep running with it?

Depends on the FMI

How urgent it is depends on the FMI after SPN 3483 - pick it below.

What should I check first?

Read other stored aftertreatment faults first, since they usually block regeneration

Then 4 more checks
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Connect a J1939-capable scan tool to the 9-pin diagnostic port.

Which FMI shows after SPN 3483?

You'll notice: The regeneration status is abnormal, so the ECM may block or abandon a regeneration.

Find the number shown after SPN 3483 on your display.

  • 0SPN 3483 FMI 0: Value is above the normal range, most severe levelReal conditionMack MP8, Mack MP7, Volvo D13
  • 1SPN 3483 FMI 1: Value is below the normal range, most severe levelReal conditionMack MP8, Mack MP7, Volvo D13
  • 10SPN 3483 FMI 10: The value is changing at an abnormal rateErratic or implausibleMack MP8, Mack MP7, Volvo D13
  • 12SPN 3483 FMI 12: Bad intelligent device or componentPart or controllerMack MP8, Mack MP7, Volvo D13
  • 13SPN 3483 FMI 13: The value is out of calibrationPart or controllerMack MP8, Mack MP7, Volvo D13
  • 15SPN 3483 FMI 15: Value is above the normal range, least severe levelReal conditionMack MP8, Mack MP7, Volvo D13
  • 17SPN 3483 FMI 17: Value is below the normal range, least severe levelReal conditionMack MP8, Mack MP7, Volvo D13
  • 31SPN 3483 FMI 31: A condition exists: the ECM is flagging a defined state rather than a circuit failureReal conditionMack MP8, Mack MP7, Volvo D13

Checks

0 of 5 done

When to stop

Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.

How urgent SPN 3483 is depends on its FMI and whether the engine has derated. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Causes

  • Regeneration blocked by another fault such as a temperature sensor, pressure sensor or doser problem
  • Regeneration interrupted by an operator inhibit switch or the engine shutting down
  • Aftertreatment controller communication or software fault
  • Sensor fault giving a false regeneration progress reading

Source

Mack MP8 2010-2013 fault code list (Diesel Laptops)

This list names SPN 3483 and the FMIs above for the engines it covers. The guidance on this page is general, not taken from it.

The source covers: Mack MP7 and MP8; same SPN on other J1939 engines.

Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.