J1939 · Aftertreatment - DPF
SPN 3695 Fault Code
DPF regeneration inhibit switch
What does SPN 3695 mean?
Cab switch that tells the engine to hold off a DPF regeneration, for example near fuel or in a closed shed. How urgent it is depends on the FMI after SPN 3695 - pick it below. Check first: look at the switch position in the cab, then watch the inhibit status in live data as you flip it.
- SPN 3695
- DPF regeneration inhibit switch
- FMI ?
- How it failed - the number after the SPN
Can I keep running with it?
Depends on the FMI
How urgent it is depends on the FMI after SPN 3695 - pick it below.
What should I check first?
Look at the switch position in the cab, then watch the inhibit status in live data as you flip it
Then 4 more checksWhere to read it
Connect a J1939-capable scan tool to the 9-pin diagnostic port.
Which FMI shows after SPN 3695?
You'll notice: A driver who leaves the inhibit on stops regeneration, so soot keeps loading and the DPF lamp escalates towards a derate.
Find the number shown after SPN 3695 on your display.
- 2SPN 3695 FMI 2: DPF regeneration inhibit switch data is erratic, intermittent or incorrectErratic or implausibleCummins ISX15
- 9SPN 3695 FMI 9: Abnormal update rate: the DPF regeneration inhibit switch data is late or not arrivingLost messageDetroit DD15, Detroit DD13, Mack MP8, Mack MP7 and 1 more
- 13SPN 3695 FMI 13: The DPF regeneration inhibit switch value is out of calibrationPart or controllerDetroit DD15, Detroit DD13
- 14SPN 3695 FMI 14: Special-instruction fault for the DPF regeneration inhibit switch; the maker lists a dedicated procedure for itOtherDetroit DD15, Detroit DD13
- 18SPN 3695 FMI 18: DPF regeneration inhibit switch is below the normal range, moderately severe levelReal conditionPACCAR MX-13
- 19SPN 3695 FMI 19: Network data received for the DPF regeneration inhibit switch is in errorLost messageDetroit DD15, Detroit DD13, PACCAR MX-13
Checks
0 of 5 done
When to stop
Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.
How urgent SPN 3695 is depends on its FMI and whether the engine has derated. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Causes
- Inhibit switch left in the inhibit position
- Switch contacts worn or stuck
- Body controller sending a stale inhibit message after a power loss
- Switch wiring chafed behind the dash
Other Aftertreatment - DPF codes
- SPN 3696DPF regeneration force switch
- SPN 3711DPF regeneration blocked by low exhaust temperature
- SPN 81DPF intake pressure
- SPN 3242DPF intake temperature sensor
- SPN 3245DPF outlet temperature
- SPN 3246DPF outlet temperature sensor
- SPN 3249DPF intake temperature
- SPN 3250Diesel oxidation catalyst outlet temperature
Source
Cummins ISX15 2013-2018 fault codes list (Diesel Laptops)
This list names SPN 3695 and the FMIs above for the engines it covers. The guidance on this page is general, not taken from it.
The source covers: Cummins ISX15, Detroit DD13, Detroit DD15, PACCAR MX-13, Mack MP7, Mack MP8, Volvo D13; same SPN on other J1939 engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
