J1939 · Aftertreatment - DPF
SPN 4765 Fault Code
Aftertreatment 1 diesel oxidation catalyst intake gas temperature
What does SPN 4765 mean?
Exhaust temperature entering the oxidation catalyst, read by a sensor at the DOC inlet. The ECM uses it to decide when the DOC is hot enough for regeneration dosing. How urgent it is depends on the FMI after SPN 4765 - pick it below. Check first: compare the DOC inlet temperature with the turbo outlet temperature after a cold soak; they should be within a few degrees.
- SPN 4765
- Aftertreatment 1 diesel oxidation catalyst intake gas temperature
- FMI ?
- How it failed - the number after the SPN
Can I keep running with it?
Depends on the FMI
How urgent it is depends on the FMI after SPN 4765 - pick it below.
What should I check first?
Compare the DOC inlet temperature with the turbo outlet temperature after a cold soak; they should be within a few degrees
Then 4 more checksWhere to read it
Connect a J1939-capable scan tool to the 9-pin diagnostic port.
Which FMI shows after SPN 4765?
You'll notice: The ECM loses the exhaust temperature going into the oxidation catalyst, so it cannot confirm the DOC is hot enough to light off injected fuel.
Find the number shown after SPN 4765 on your display. 2 of them have their own page with causes and checks.
- 2SPN 4765 FMI 2: Data is erratic, intermittent or incorrectErratic or implausibleCummins ISX15, PACCAR MX-13
- 3SPN 4765 FMI 3: Signal voltage is above normal, or the circuit is shorted to a high sourceShorted highCummins ISX15, PACCAR MX-13
- 4SPN 4765 FMI 4: Signal voltage is below normal, or the circuit is shorted to a low sourceShorted lowCummins ISX15, PACCAR MX-13
- 16SPN 4765 FMI 16: Value is above the normal range, moderately severe levelReal conditionCummins ISX15, PACCAR MX-13
- 19SPN 4765 FMI 19: The DOC intake temperature message arrived in error over CANLost messagePACCAR MX-13
Checks
0 of 5 done
When to stop
Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.
How urgent SPN 4765 is depends on its FMI and whether the engine has derated. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Causes
- Reads cold: an open circuit or a short to supply in the DOC intake temperature sensor wiring, which the ECM reads as an extremely low temperature
- Reads hot: signal wire shorted to ground or the DOC intake temperature sensor element shorted, which the ECM reads as an extremely high temperature
- Real condition: real low exhaust temperature after a long idle, so the DOC never reaches light-off and dosing stays blocked
- Real condition: exhaust leak at the turbo outlet flange letting in cool air ahead of the sensor
1 more causeFewer causes
- Sensor: turbo vibration making the plug lose contact at certain engine speeds
Other Aftertreatment - DPF codes
Source
Cummins ISX15 2013-2018 fault codes list (Diesel Laptops)
This list names SPN 4765 and the FMIs above for the engines it covers. The guidance on this page is general, not taken from it.
The source covers: Cummins ISX15 (2013-2018) and X15; same SPN on other J1939 engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
