EF Logo

J1939 · Aftertreatment - DPF

SPN 5742 Fault Code

Aftertreatment diesel particulate filter temperature sensor module

What does SPN 5742 mean?

The module that gathers the DPF-area exhaust temperature sensors and reports them to the ECM. Its health decides whether those temperature signals are trusted. How urgent it is depends on the FMI after SPN 5742 - pick it below. Check first: measure the module supply and ground at its plug with the key on.

FaultActiveSPN 5742FMI --J1939 engine ECU
SPN 5742
Aftertreatment diesel particulate filter temperature sensor module
FMI ?
How it failed - the number after the SPN

Can I keep running with it?

Depends on the FMI

How urgent it is depends on the FMI after SPN 5742 - pick it below.

What should I check first?

Measure the module supply and ground at its plug with the key on

Then 4 more checks
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Connect a J1939-capable scan tool to the 9-pin diagnostic port.

Which FMI shows after SPN 5742?

You'll notice: The temperature module for the particulate filter has failed or lost communication, so the ECM does not get the gas temperatures it needs to run a safe regeneration.

Find the number shown after SPN 5742 on your display.

  • 3SPN 5742 FMI 3: Signal voltage is above normal, or the circuit is shorted to a high sourceShorted highCummins ISX15, PACCAR MX-13
  • 4SPN 5742 FMI 4: Signal voltage is below normal, or the circuit is shorted to a low sourceShorted lowCummins ISX15, PACCAR MX-13
  • 9SPN 5742 FMI 9: Abnormal update rate: the signal or message is late or missingLost messageCummins ISX15
  • 11SPN 5742 FMI 11: A fault exists but the ECM cannot identify its causeOtherCummins ISX15
  • 12SPN 5742 FMI 12: Bad intelligent device or componentPart or controllerCummins ISX15
  • 16SPN 5742 FMI 16: Value is above the normal range, moderately severe levelReal conditionCummins ISX15

Checks

0 of 5 done

When to stop

Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.

How urgent SPN 5742 is depends on its FMI and whether the engine has derated. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Causes

  • Supply or ground fault at the filter-side module plug, such as a corroded pin or a blown fuse
  • CAN pair between the module and the ECM open, shorted or noisy
  • Module cooked by heat and vibration at the canister
  • Probe leads from the module to the filter damaged by exhaust heat

Source

Cummins ISX15 2013-2018 fault codes list (Diesel Laptops)

This list names SPN 5742 and the FMIs above for the engines it covers. The guidance on this page is general, not taken from it.

The source covers: Cummins ISX15 (2013-2018) and X15; same SPN on other J1939 engines.

Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.