J1939 · Aftertreatment - DPF
SPN 5741 Fault Code
Soot sensor electrode
What does SPN 5741 mean?
Soot sensor with inter-digital electrodes, placed after the DPF to detect soot leaking past a damaged filter. How urgent it is depends on the FMI after SPN 5741 - pick it below. Check first: inspect the soot sensor and its protective tube for damage and heavy soot.
- SPN 5741
- Soot sensor electrode
- FMI ?
- How it failed - the number after the SPN
Can I keep running with it?
Depends on the FMI
How urgent it is depends on the FMI after SPN 5741 - pick it below.
What should I check first?
Inspect the soot sensor and its protective tube for damage and heavy soot
Then 4 more checksWhere to read it
Connect a J1939-capable scan tool to the 9-pin diagnostic port.
Which FMI shows after SPN 5741?
You'll notice: The system cannot confirm that the DPF is working, so an emissions lamp may light and a derate may be set if it is not fixed.
Find the number shown after SPN 5741 on your display.
- 2SPN 5741 FMI 2: Soot sensor electrode data is erratic, intermittent or incorrectErratic or implausiblePACCAR MX-13
- 3SPN 5741 FMI 3: Soot sensor electrode signal voltage is above normal, or the circuit is shorted to a high sourceShorted highPACCAR MX-13
- 4SPN 5741 FMI 4: Soot sensor electrode signal voltage is below normal, or the circuit is shorted to a low sourceShorted lowDetroit DD15, Detroit DD13, Detroit DD13 Gen 5, Detroit DD15 Gen 5 and 1 more
- 9SPN 5741 FMI 9: Abnormal update rate: the Soot sensor electrode data is late or not arrivingLost messageDetroit DD15, Detroit DD13, Detroit DD13 Gen 5, Detroit DD15 Gen 5
- 12SPN 5741 FMI 12: Failure inside the device or component that handles the Soot sensor electrodePart or controllerDetroit DD15, Detroit DD13, Detroit DD13 Gen 5, Detroit DD15 Gen 5
- 13SPN 5741 FMI 13: The Soot sensor electrode value is out of calibrationPart or controllerDetroit DD15, Detroit DD13, Detroit DD13 Gen 5, Detroit DD15 Gen 5
- 16SPN 5741 FMI 16: Soot sensor electrode is above the normal range, moderately severe levelReal conditionDetroit DD15, Detroit DD13, Detroit DD13 Gen 5, Detroit DD15 Gen 5
- 18SPN 5741 FMI 18: Soot sensor electrode is below the normal range, moderately severe levelReal conditionDetroit DD15, Detroit DD13, Detroit DD13 Gen 5, Detroit DD15 Gen 5
Checks
0 of 5 done
When to stop
Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.
How urgent SPN 5741 is depends on its FMI and whether the engine has derated. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Causes
- Soot sensor element fouled, cracked or shorted
- Soot sensor control unit failed or without supply
- Connector water ingress
- DPF leaking soot, so the sensor signal is correct
Other Aftertreatment - DPF codes
Source
PACCAR MX-13 2013-2016 fault codes list (Diesel Laptops)
This list names SPN 5741 and the FMIs above for the engines it covers. The guidance on this page is general, not taken from it.
The source covers: Detroit DD13, Detroit DD15, PACCAR MX-13; same SPN on other J1939 engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
