J1939 · Sensors
SPN 171 Fault Code
Ambient air temperature
What does SPN 171 mean?
Outside air temperature, read by a sensor on the cab or bumper or received over the data link. The ECM and aftertreatment controls use it for cold-start, DEF heating and regeneration decisions. How urgent it is depends on the FMI after SPN 171 - pick it below. Check first: compare the reading with the real outside temperature on a cold-soaked machine; large offsets point to the sensor or its wiring.
- SPN 171
- Ambient air temperature
- FMI ?
- How it failed - the number after the SPN
Can I keep running with it?
Depends on the FMI
How urgent it is depends on the FMI after SPN 171 - pick it below.
What should I check first?
Compare the reading with the real outside temperature on a cold-soaked machine; large offsets point to the sensor or its wiring
Then 4 more checksWhere to read it
Connect a J1939-capable scan tool to the 9-pin diagnostic port.
Which FMI shows after SPN 171?
You'll notice: Outside temperature on the dash reads wrong or shows dashes, and the ECM may delay cold-start aids or fan strategy.
Find the number shown after SPN 171 on your display. 2 of them have their own page with causes and checks.
- 2SPN 171 FMI 2: Data is erratic, intermittent or incorrectErratic or implausibleCummins ISX15, Detroit DD15, Detroit DD13, Detroit DD13 Gen 5 and 5 more
- 3SPN 171 FMI 3: Signal voltage is above normal, or the circuit is shorted to a high sourceShorted highCummins ISX15, Detroit DD15, Detroit DD13, Detroit DD13 Gen 5 and 2 more
- 4SPN 171 FMI 4: Signal voltage is below normal, or the circuit is shorted to a low sourceShorted lowCummins ISX15, Detroit DD15, Detroit DD13, Detroit DD13 Gen 5 and 2 more
- 9SPN 171 FMI 9: Abnormal update rate: the signal or message is late or missingLost messageCummins ISX15, Mack MP8, Mack MP7, Volvo D13
- 10SPN 171 FMI 10: The value is changing at an abnormal rateErratic or implausibleMack MP8, Mack MP7, PACCAR MX-13, Volvo D13
- 12SPN 171 FMI 12: Bad intelligent device or componentPart or controllerMack MP8, Mack MP7, Volvo D13
- 13SPN 171 FMI 13: The value is out of calibrationPart or controllerMack MP8, Mack MP7, Volvo D13
- 14SPN 171 FMI 14: A special-instruction condition defined by the engine maker appliesOtherMack MP8, Mack MP7, Volvo D13
- 19SPN 171 FMI 19: Network data for this parameter was received in errorLost messageCummins ISX15, Mack MP8, Mack MP7, Volvo D13
- 20SPN 171 FMI 20: Ambient temperature sensor reading is not plausibleErratic or implausibleDetroit DD15, Detroit DD13, Detroit DD13 Gen 5, Detroit DD15 Gen 5
Checks
0 of 5 done
When to stop
Let the engine cool before opening the cooling system; a hot cap releases scalding coolant. Running on with an overheat warning risks a head gasket or seized engine.
How urgent SPN 171 is depends on its FMI and whether the engine has derated. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Causes
- Reads cold: an open circuit or a short to supply in the ambient air temperature sensor wiring, which the ECM reads as an extremely low temperature
- Reads hot: signal wire shorted to ground or the ambient air temperature sensor element shorted, which the ECM reads as an extremely high temperature
- Real condition: sensor mounted where engine heat or radiator air biases the reading
- Real condition: wrong sensor fitted after bumper or grille work
1 more causeFewer causes
- Sensor: sun or radiator heat soaking the sensor so the reading drifts upward while parked
Other Sensors codes
Source
Cummins ISX15 2013-2018 fault codes list (Diesel Laptops)
This list names SPN 171 and the FMIs above for the engines it covers. The guidance on this page is general, not taken from it.
The source covers: Cummins ISX15 (2013-2018) and X15; same SPN on other J1939 engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
