Equipment fault codes
Type the code exactly as your machine shows it and get what it means, how urgent it is and what to check first.
Tryor a problem, like “rail pressure”
8,092 codes from 17 makers, each with its source.
Fault codes by maker
Engine codes first, then lifts, then machines.
- Stop now612 codes
- Shut down and fix before working on. Running on risks damage or the machine locks out.
- Check soon5,967 codes
- The machine may derate or limit a function. Find the cause before the next shift.
- Information439 codes
- A reminder or status message. Nothing is failing yet.
- J1939 SPN / FMITrucks, Excavators323codes
- CumminsTrucks, Excavators831codes
- DeutzTelehandlers, Lifts619codes
- Detroit DieselTrucks, Tractor units750codes
- Volvo / Mack trucksTrucks, Tractor units174codes
- JLGBoom lifts, Scissor lifts259codes
- GenieScissor lifts, Boom lifts303codes
- SkyjackScissor lifts81codes
- BobcatSkid steers, Track loaders1,258codes
- JCBBackhoe loaders, Telehandlers718codes
- John DeereExcavators, Skid steers407codes
- CatWheel loaders74codes
- KomatsuExcavators153codes
- HyundaiExcavators, Wheel loaders231codes
- Develon (Doosan)Excavators, Wheel loaders363codes
- KubotaTrack loaders, Skid steers189codes
- Thermo KingReefer trucks, Reefer trailers285codes
- Maker not listed? Most diesel engines report J1939 codes, an SPN with an FMI.SPN / FMI lookupMachine down? Post a request
Know the failure mode
Most codes fail in one of six ways. Which one tells you the first test, whatever the maker.
- 01
Shorted high
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. The signal sits at or near the supply voltage - more than a working sensor can send.
How to test
- Meter test
- Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
- Good result
- Open circuit (OL) between them. Any low reading is the short.
- 02
Shorted low
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. The signal sits at or near zero volts - less than a working sensor can send.
How to test
- Meter test
- Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
- Good result
- Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
- 03
Open circuit
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. No current flows, or the signal floats - a wire, pin or coil is broken.
How to test
- Meter test
- Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.
- Good result
- Near 0 Ω on each wire. The part reads its listed resistance, not OL.
- 04
Lost message
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. A module stopped hearing another on the data link, or the data came late or garbled.
How to test
- Meter test
- Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
- Good result
- About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
- 05
Erratic or implausible
The reading against the band the controller allows. The reading jumps, drifts or disagrees with the sensors around it.
How to test
- Meter test
- Watch the live value on the service tool while you flex the harness and tap the connector.
- Good result
- A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
- 06
Real condition
The reading against the band the controller allows. The sensor reading is valid but outside the allowed range - the problem may be real.
How to test
- Meter test
- Check the real value with a separate gauge or thermometer before blaming the sensor.
- Good result
- If the gauge agrees with the display, fix the machine, not the sensor.
General guidance on typical circuits, not a maker's wiring diagram.
Reading the code on your display
J1939 diesel engines
SPN 3226
SPN
Outlet NOx sensor - what is at fault
FMI 10
FMI
Abnormal rate of change - how it failed
John Deere
ECU
Controller
Engine control unit
000100
SPN
Engine oil pressure
.01
FMI
Low, most severe level
Bobcat
M
Series
M- and R-series machine
09
System
Fuel level
09
Fault
Too low
Engine P-codes (JCB)
P
Area
Powertrain
0
Type
Standard SAE code
087
Fault
Fuel rail pressure too low
Quick answers
Where do I find the fault code on my machine?
Most machines show it on the cab display or instrument cluster, often with a warning lamp lit. Lifts show it on the ground or platform control box, some as a number of LED flashes. When nothing shows, a service tool plugged into the 9-pin diagnostic port under the dash reads the stored codes. Type the code exactly as shown into the search.
What do SPN and FMI mean?
On J1939 engines the SPN (suspect parameter number) names the part or value at fault and the FMI (failure mode identifier) says how it failed. FMI 3 is "voltage above normal or shorted high", FMI 4 "voltage below normal or shorted low". So SPN 100 FMI 4 reads as: oil pressure sensor voltage low. The SPN says where to look, the FMI which test to run first.
Which fault codes mean stop now?
612 of the codes listed here are marked Stop now. Shut down and fix before working on. Running on risks damage or the machine locks out. Ones looked up often: J1939 SPN 100, Cummins 111, Deutz SPN 100 FMI 0, Detroit SPN 100 FMI 1. Check soon codes (5,967) mean finding the cause before the next shift.
What should I check first when a code comes up?
Read how it failed before buying parts. Shorted high, shorted low and open circuit codes are usually wiring: check the connector and harness with a meter first. A lost message points to the data link between modules. A real-condition code means the sensor saw a real problem, so confirm it with a separate gauge before blaming the sensor.
Are fault codes the same for every maker?
No. Each maker numbers its own codes, so look a code up under the maker on the machine's plate. The exception is J1939: most diesel engines report the same SPN and FMI numbers whoever built the machine, which is why 107 SPN and FMI pairs are listed once, under J1939.
Codes looked up most
Across all makers, one from each in turn.
- J1939SPN 27EGR valve position
- Cummins111Engine control module - critical internal failure
- DeutzSPN 91 FMI 3Machine - Position accelerator pedal (sensor 1) - Voltage above normal or shorted to high source
- DetroitSPN 100 FMI 1Low Engine Oil Pressure
- Volvo/MackMID 128 SID 1 FMI 3Injector cylinder 1 circuit shorted high
- JLG2-1Footswitch or keyswitch fault
- GeniebrBrake release
- SkyjackF-0-0-1Charger fault: DC-DC (LLC) excessive leakage
- Bobcat01-17Air filter plugged
- JCBP0002Rail pressure control error (too high)
- John DeereECU 000097.03Water in fuel sensor voltage high
- CatCID 41 FMI 038 V sensor supply voltage high
- KomatsuB@BAZGEngine oil pressure low
- HyundaiF6TCU clutch adjustment data lost
- DevelonV000201Gauge panel error
- KubotaE:001CAN communication error
- Thermo King02Check evaporator coil sensor
- J1939SPN 81DPF intake pressure
- Cummins115Engine speed/position - both sensor signals lost
- DeutzSPN 91 FMI 4Machine - Position accelerator pedal (sensor 1) - Voltage below normal or shorted to low source
- DetroitSPN 111 FMI 1Coolant Level Very Low
- Volvo/MackMID 128 SID 1 FMI 5Injector cylinder 1 circuit open or shorted to ground
- JLG2-2Drive or steer selection fault
- GenieCHChassis mode operation
76 more codes looked up most, by maker
J1939
Cummins
Deutz
- SPN 91 FMI 11Machine - Position accelerator pedal (sensor 1) - Root cause not known
- SPN 94 FMI 1Engine - Fuel low pressure sensor - Data below normal operational range (Most severe level)
- SPN 94 FMI 3Engine - Fuel low pressure sensor - Voltage above normal or shorted to high source
- SPN 94 FMI 4Engine - Fuel low pressure sensor - Voltage below normal or shorted to low source
