Detroit · Communication
Detroit Fault Code SPN 1231 FMI 9
ACM Message Not Received or has Stopped Arriving
What does Detroit code SPN 1231 FMI 9 mean?
A controller stopped receiving the CAN message from the ACM (or the MCM CAN1 signal in some lists). Detroit logs this when the module is not powered, is resetting or the CAN link is damaged. Urgency: check soon - the machine may derate or limit a function. Check first: check the ACM fuse, power and ground, and the ignition feed with the key on.
- SPN 1231
- What is at fault
- FMI 9
- Abnormal update rate
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Check the ACM fuse, power and ground, and the ignition feed with the key on.
Then 4 more checksWhere to read it
Connect a Detroit-capable diagnostic tool (Diagnostic Link or a compatible scan tool) to the vehicle diagnostic socket.
Checks
0 of 5 done
Causes
- ACM without power, ground or ignition feed
- CAN wiring open or chafed between the MCM and the ACM
- Terminating resistor or connector fault on the data link
- ACM or MCM software mismatch or reset
How it failed
You'll notice: The aftertreatment lamps may light, the engine may derate and several other codes often appear at the same time.
Lost messageRead from FMI 9: abnormal update rate
A module stopped hearing another on the data link, or the data came late or garbled.
- Meter test
- Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
- Good result
- About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
When to stop
Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Engine-side CAN link (MCM, ACM, CPC5)
8 other codes on this part are also lost message (SPN 84 FMI 11, SPN 84 FMI 19, SPN 190 FMI 9, SPN 190 FMI 14 and more). When they show together, start at the wiring and connector they share.
- SPN 625 FMI 8MCM PT-CAN DM1 Message Not Received or has Stopped ArrivingErratic or implausibleCheck soon
- SPN 625 FMI 9ACM PT-CAN DM1 Message Not Received or has Stopped ArrivingLost messageCheck soon
- SPN 625 FMI 17No ACM2 Communication - Pre-WarningReal conditionCheck soon
- SPN 625 FMI 18No ACM2 Communication - WarningReal conditionCheck soon
- SPN 639 FMI 14J1939 Data Link FailureLost messageCheck soon
- SPN 1231 FMI 9ACM Message Not Received or has Stopped ArrivingLost messageCheck soon
- SPN 1231 FMI 14Powertrain-CAN Short to Battery - Bus offShorted highCheck soon
- SPN 1669 FMI 9Aftertreatment Control Module CAN 4 Signal MissingLost messageCheck soon
- SPN 2000 FMI 9Lost Communication with a CPC ModuleLost messageCheck soon
Show the other 12 codesHide the other codes
- SPN 84 FMI 0Vehicle Speed Above Programmable Threshold 1 While DrivingReal conditionCheck soon
- SPN 84 FMI 6VSS Anti-Tamper Detection via ABS Vehicle Speed ComparisonShorted lowCheck soon
- SPN 84 FMI 11Vehicle Speed Above Programmable Threshold 2 While DrivingLost messageCheck soon
- SPN 84 FMI 13Vehicle Speed Over PTCAN Not AvailablePart or controllerCheck soon
- SPN 84 FMI 19Vehicle Speed Value Outside Allowable RangeLost messageCheck soon
- SPN 84 FMI 20Vehicle Speed FailureErratic or implausibleCheck soon
- SPN 84 FMI 21Vehicle Speed FailureErratic or implausibleCheck soon
- SPN 190 FMI 9Engine Speed Signal not Available via Controller Area Network (CAN)Lost messageCheck soon
- SPN 190 FMI 14Engine Overspeed while DrivingLost messageStop now
- SPN 190 FMI 15Engine Overspeed Pre-WarningReal conditionStop now
- SPN 190 FMI 16Engine Overspeed while StationaryReal conditionStop now
- SPN 625 FMI 2Invalid Data on Engine CAN LinkErratic or implausibleCheck soon
Related on Equipments Finder
Source
Detroit Diesel DD15 Gen 5 (2023) Fault Codes List, Diesel Repair (SPN/FMI with Detroit descriptions)
This source lists SPN 1231 FMI 9 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Detroit DD13, DD15, DD16 (GHG14/GHG17, Gen 5) with MCM, ACM and CPC5.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
