EF Logo

Detroit · Communication

Detroit Engine-side CAN link (MCM, ACM, CPC5) fault codes

The MCM, ACM and CPC5 exchange data over CAN. Detroit logs a missing message, a bus-off, a CAN signal that is faulty and the loss of the ACM2 or CPC module.

FaultCheckSPN 1231FMI 9Detroit · Engine-side CAN link (MCM, ACM, CPC5)
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Connect a Detroit-capable diagnostic tool (Diagnostic Link or a compatible scan tool) to the vehicle diagnostic socket.

What do these codes mean?

Detroit codes SPN 84 FMI 0 to SPN 2000 FMI 9 are all about the engine-side CAN link (MCM, ACM, CPC5). The most common failure type is lost message (9 of 21); 3 need an immediate stop. Start with this check: check the CAN wiring and the terminating resistance on the data link.

How urgent are they?

3 of 21 codes here mean stop now; the other 18 can wait until the shift ends, but find the cause before the next one.

  • Stop now3
  • Check soon18

What should I check first?

Check the CAN wiring and the terminating resistance on the data link.

Shared checks

21 of 21

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Detroit SPN 84 FMI 0Vehicle Speed Above Programmable Threshold 1 While Driving

    Detroit lists SPN 84 FMI 0 as "Vehicle Speed Above Programmable Threshold 1 While Driving".· Real condition
    Check soon

    Causes

    • Software mismatch among modules
    • Wiring or connector fault on the data link

    Checks

    1. 1Compare the software versions of the modules.
    2. 2Check the data link wiring for chafing and corrosion.
    3. 3Ask the driver whether the truck was driven above the programmed road speed limit, and read the limit set in the CPC5 parameters.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Detroit SPN 84 FMI 6VSS Anti-Tamper Detection via ABS Vehicle Speed Comparison

    Detroit lists SPN 84 FMI 6 as "VSS Anti-Tamper Detection via ABS Vehicle Speed Comparison".· Shorted low
    Check soon

    Causes

    • Software mismatch among modules
    • Wiring or connector fault on the data link

    Checks

    1. 1Compare the software versions of the modules.
    2. 2Check the data link wiring for chafing and corrosion.
    3. 3Compare the speed from the transmission sensor with the ABS wheel speed; a mismatch suggests a wrong tire or axle parameter or a tampered sensor.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Detroit SPN 84 FMI 11Vehicle Speed Above Programmable Threshold 2 While Driving

    Same failure as SPN 84 FMI 0 ("Vehicle Speed Above Programmable Threshold 1 While Driving") on a sibling part: Detroit lists SPN 84 FMI 11 as "Vehicle Speed Above Programmable Threshold 2 While Driving".· Lost message
    Check soon

    Causes

    • The causes listed under SPN 84 FMI 0, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 84 FMI 0, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • Detroit SPN 84 FMI 13Vehicle Speed Over PTCAN Not Available

    Same failure as SPN 1231 FMI 9 ("ACM Message Not Received or has Stopped Arriving") on a sibling part: Detroit lists SPN 84 FMI 13 as "Vehicle Speed Over PTCAN Not Available".· Part or controller
    Check soon

    Causes

    • The causes listed under SPN 1231 FMI 9, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 1231 FMI 9, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    ControllerPartSupplySignalGround?
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Check power and ground at the module connector with the key on, then its fuses.

    Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

  • Detroit SPN 84 FMI 19Vehicle Speed Value Outside Allowable Range

    Detroit lists SPN 84 FMI 19 as "Vehicle Speed Value Outside Allowable Range".· Lost message
    Check soon

    Causes

    • Power or ground missing at that module
    • CAN wiring fault between the modules

    Checks

    1. 1Check the power and ground feeds of the module that is not reporting.
    2. 2Check the CAN wiring and terminating resistance.
    3. 3Check that the tire size and axle ratio parameters match the truck, because a wrong value pushes the calculated speed out of range.
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • Detroit SPN 84 FMI 20Vehicle Speed Failure

    Detroit lists SPN 84 FMI 20 as "Vehicle Speed Failure".· Erratic or implausible
    Check soon

    Causes

    • Software mismatch among modules
    • Wiring or connector fault on the data link

    Checks

    1. 1Compare the software versions of the modules.
    2. 2Check the data link wiring for chafing and corrosion.
    3. 3Watch the speed signal on a road test and compare it with the dash and a GPS speed to see where it drops out.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Detroit SPN 84 FMI 21Vehicle Speed Failure

    Same failure as SPN 84 FMI 20 ("Vehicle Speed Failure") on a sibling part: Detroit lists SPN 84 FMI 21 as "Vehicle Speed Failure".· Erratic or implausible
    Check soon

    Causes

    • The causes listed under SPN 84 FMI 20, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 84 FMI 20, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Detroit SPN 190 FMI 9Engine Speed Signal not Available via Controller Area Network (CAN)

    Same failure as SPN 1231 FMI 9 ("ACM Message Not Received or has Stopped Arriving") on a sibling part: Detroit lists SPN 190 FMI 9 as "Engine Speed Signal not Available via Controller Area Network (CAN)".· Lost message
    Check soon

    Causes

    • The causes listed under SPN 1231 FMI 9, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 1231 FMI 9, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • Detroit SPN 190 FMI 14Engine Overspeed while Driving

    Detroit lists SPN 190 FMI 14 as "Engine Overspeed while Driving".· Lost message
    Stop now

    Causes

    • Power or ground missing at that module
    • CAN wiring fault between the modules

    Checks

    1. 1Check the power and ground feeds of the module that is not reporting.
    2. 2Check the CAN wiring and terminating resistance.
    3. 3Ask whether the engine was over-revved on a downshift and read the freeze-frame engine speed; inspect the drivetrain if it happened.
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • Detroit SPN 190 FMI 15Engine Overspeed Pre-Warning

    Detroit lists SPN 190 FMI 15 as "Engine Overspeed Pre-Warning".· Real condition
    Stop now

    Causes

    • Software mismatch among modules
    • Wiring or connector fault on the data link

    Checks

    1. 1Compare the software versions of the modules.
    2. 2Check the data link wiring for chafing and corrosion.
    3. 3This is the warning before the shutdown; check the retarder use and the gear the truck was in when the speed climbed.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Detroit SPN 190 FMI 16Engine Overspeed while Stationary

    Detroit lists SPN 190 FMI 16 as "Engine Overspeed while Stationary".· Real condition
    Stop now

    Causes

    • Software mismatch among modules
    • Wiring or connector fault on the data link

    Checks

    1. 1Compare the software versions of the modules.
    2. 2Check the data link wiring for chafing and corrosion.
    3. 3An overspeed with the vehicle stopped points to a governor, pedal or fuel-supply problem such as runaway oil or a stuck injector.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Detroit SPN 625 FMI 2Invalid Data on Engine CAN Link

    Detroit lists SPN 625 FMI 2 as "Invalid Data on Engine CAN Link".· Erratic or implausible
    Check soon

    Causes

    • Power or ground missing at that module
    • CAN wiring fault between the modules

    Checks

    1. 1Check the power and ground feeds of the module that is not reporting.
    2. 2Check the CAN wiring and terminating resistance.
    3. 3Read the content of the engine CAN message with the tool and look for values that do not change or are out of range.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Detroit SPN 625 FMI 8MCM PT-CAN DM1 Message Not Received or has Stopped Arriving

    Same failure as SPN 1231 FMI 9 ("ACM Message Not Received or has Stopped Arriving") on a sibling part: Detroit lists SPN 625 FMI 8 as "MCM PT-CAN DM1 Message Not Received or has Stopped Arriving".· Erratic or implausible
    Check soon

    Causes

    • The causes listed under SPN 1231 FMI 9, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 1231 FMI 9, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Detroit SPN 625 FMI 9ACM PT-CAN DM1 Message Not Received or has Stopped Arriving

    Same failure as SPN 1231 FMI 9 ("ACM Message Not Received or has Stopped Arriving") on a sibling part: Detroit lists SPN 625 FMI 9 as "ACM PT-CAN DM1 Message Not Received or has Stopped Arriving".· Lost message
    Check soon

    Causes

    • The causes listed under SPN 1231 FMI 9, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 1231 FMI 9, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • Detroit SPN 625 FMI 17No ACM2 Communication - Pre-Warning

    Detroit lists SPN 625 FMI 17 as "No ACM2 Communication - Pre-Warning".· Real condition
    Check soon

    Causes

    • Software mismatch among modules
    • Wiring or connector fault on the data link

    Checks

    1. 1Compare the software versions of the modules.
    2. 2Check the data link wiring for chafing and corrosion.
    3. 3This is the warning stage of an ACM2 communication loss; check the ACM2 power, ground and CAN wiring before it escalates.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Detroit SPN 625 FMI 18No ACM2 Communication - Warning

    Detroit lists SPN 625 FMI 18 as "No ACM2 Communication - Warning".· Real condition
    Check soon

    Causes

    • Software mismatch among modules
    • Wiring or connector fault on the data link

    Checks

    1. 1Compare the software versions of the modules.
    2. 2Check the data link wiring for chafing and corrosion.
    3. 3This is the warning stage after the pre-warning; check the ACM2 module and its power, because the aftertreatment can no longer be managed.
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Detroit SPN 639 FMI 14J1939 Data Link Failure

    Detroit lists SPN 639 FMI 14 as "J1939 Data Link Failure".· Lost message
    Check soon

    Causes

    • Power or ground missing at that module
    • CAN wiring fault between the modules

    Checks

    1. 1Check the power and ground feeds of the module that is not reporting.
    2. 2Check the CAN wiring and terminating resistance.
    3. 3Check the J1939 data link for a module that pulls the bus down by unplugging modules one at a time.
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • Detroit SPN 1231 FMI 9ACM Message Not Received or has Stopped Arriving

    A controller stopped receiving the CAN message from the ACM (or the MCM CAN1 signal in some lists).· Lost message
    Check soon

    Causes

    • ACM without power, ground or ignition feed
    • CAN wiring open or chafed between the MCM and the ACM
    • Terminating resistor or connector fault on the data link
    • ACM or MCM software mismatch or reset

    Checks

    1. 1Check the ACM fuse, power and ground, and the ignition feed with the key on.
    2. 2Measure the CAN link resistance at the diagnostic socket and compare it with the expected value for a healthy bus.
    3. 3Inspect the ACM and MCM connectors for bent pins and moisture.
    4. 4Read whether the ACM also stores a code for the missing message.
    5. 5Update the software on the modules if the versions do not match.
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • Detroit SPN 1231 FMI 14Powertrain-CAN Short to Battery - Bus off

    Detroit lists SPN 1231 FMI 14 as "Powertrain-CAN Short to Battery - Bus off".· Shorted high
    Check soon

    Causes

    • Power or ground missing at that module
    • CAN wiring fault between the modules

    Checks

    1. 1Check the power and ground feeds of the module that is not reporting.
    2. 2Check the CAN wiring and terminating resistance.
    3. 3A bus-off to battery means a CAN wire is shorted to battery voltage; check the powertrain CAN wires for contact with a power wire.
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Detroit SPN 1669 FMI 9Aftertreatment Control Module CAN 4 Signal Missing

    Same failure as SPN 1231 FMI 9 ("ACM Message Not Received or has Stopped Arriving") on a sibling part: Detroit lists SPN 1669 FMI 9 as "Aftertreatment Control Module CAN 4 Signal Missing".· Lost message
    Check soon

    Causes

    • The causes listed under SPN 1231 FMI 9, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 1231 FMI 9, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • Detroit SPN 2000 FMI 9Lost Communication with a CPC Module

    Same failure as SPN 1231 FMI 9 ("ACM Message Not Received or has Stopped Arriving") on a sibling part: Detroit lists SPN 2000 FMI 9 as "Lost Communication with a CPC Module".· Lost message
    Check soon

    Causes

    • The causes listed under SPN 1231 FMI 9, found on this part and its own connector and harness leg
    • A fault that affects only this channel and not the part that the first code names

    Checks

    1. 1Run the checks listed under SPN 1231 FMI 9, but at this part and on its own wires.
    2. 2Compare it with the sibling part that has no code; a reading that differs from it marks this one as the faulty part.
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

Shared checks

Checks, in order

  1. 1Check the CAN wiring and the terminating resistance on the data link.
  2. 2Check the power and ground of the module that is not reporting.
  3. 3Read which module the code names and test that module first.
  4. 4Update or match the software versions in the tool.

Causes

  • CAN wiring damage, a terminating resistor fault or a connector problem
  • Low battery voltage or a controller that resets
  • A module that has lost power or failed
  • Software mismatch among modules

Most common here: lost message (9 of 21)

Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

When to stop

You'll notice: Several lamps at once, a derate or no start, and often codes from more than one module.

Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.