Hyundai · Transmission TCU codes (hex)
Hyundai Fault Code F6
TCU clutch adjustment data lost
What does Hyundai code F6 mean?
The TCU could not read the stored clutch adjustment data after a TCU, valve block or transmission replacement. Urgency: check soon - the machine may derate or limit a function. Check first: run the AEB cycle with the shifter in neutral, engine at idle, parking brake applied and the transmission at working temperature.
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Run the AEB cycle with the shifter in neutral, engine at idle, parking brake applied and the transmission at working temperature
Then 3 more checksWhere this code shows
Turn the key on and open the fault code or diagnosis menu on the cluster.
Checks
0 of 4 done
Causes
- Transmission, valve block or TCU replaced without running AEB
- Stored clutch data lost
- EEPROM write failed during a previous AEB
How it failed
You'll notice: The display shows F6 and the transmission uses default clutch filling values until AEB is run.
OtherRead from how the source describes the code
The source does not say how this one failed.
- Meter test
- Read the code with the service tool and note which other codes are active with it.
- Good result
- Codes that appear together usually share one cause - start with the wiring they share.
When to stop
Lower attachments to the ground and relieve hydraulic pressure before loosening any fitting. Never feel for a leak with your hand - oil under pressure can inject through skin.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: TCU power supply, joystick, display and internal faults
- E4TCU display output: short to groundShorted lowInformation
- C5TCU joystick status indicator: short to battery voltageShorted highInformation
- D5TCU error at valve power supply VPS1OtherStop now
- E5TCU communication failure on DeviceNetOtherStop now
- F5TCU clutch failureOtherStop now
- C6TCU joystick status indicator: open circuitOpen circuitInformation
- D6TCU error at valve power supply VPS2OtherStop now
- F6TCU clutch adjustment data lostOtherCheck soon
- F7TCU substitute clutch controlOtherCheck soon
Show the other 9 codesHide the other codes
- D1TCU sensor power supply: short to battery voltageShorted highCheck soon
- F1TCU general EEPROM faultPart or controllerInformation
- D2TCU sensor power supply: short to groundShorted lowCheck soon
- F2TCU configuration lostOtherStop now
- D3TCU low voltage at batteryShorted lowStop now
- E3TCU display output: short to battery voltageShorted highInformation
- F3TCU application errorOtherStop now
- C4TCU joystick status indicator: short to groundShorted lowInformation
- D4TCU high voltage at batteryShorted highStop now
Other Hyundai codes: Transmission TCU codes (hex)
- 9ATCU converter lock-up clutch solenoid: short to ground
- 9BTCU converter lock-up clutch solenoid: open circuit
- 9CTCU converter lock-up clutch solenoid: short to battery voltage
- B9TCU engine overspeed
- 10TCU logical error at direction select signal from shift lever 3
- 11TCU logical error at gear range signal
- 12TCU logical error at direction select signal
Related on Equipments Finder
Source
This source lists F6 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Hyundai HL757-9 wheel loader (manual covers the MCU machine table and the TCU transmission table).
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
