EF Logo

Hyundai · Transmission TCU codes (hex)

Hyundai TCU power supply, joystick, display and internal faults fault codes

This group holds the joystick status indicator outputs, the TCU power and valve supplies (VPS1 and VPS2), the display output and DeviceNet link, and the TCU's own memory and configuration faults. Some of them shut the TCU down.

FaultCheckF6Hyundai · TCU power supply, joystick, display and internal faults
Code shows hereFAULTF6

Where this code shows

Turn the key on and open the fault code or diagnosis menu on the cluster.

What do these codes mean?

Hyundai codes D1 to F7 are all about the tCU power supply, joystick, display and internal faults. The most common failure type is shorted high (4 of 18); 8 need an immediate stop. Start with this check: measure battery voltage at the TCU supply pin.

How urgent are they?

8 of 18 codes here mean stop now; 4 can wait until the shift ends, but find the cause before the next one; 6 are information only.

  • Stop now8
  • Check soon4
  • Info6

What should I check first?

Measure battery voltage at the TCU supply pin

Shared checks

18 of 18

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Hyundai D1TCU sensor power supply: short to battery voltage

    The sensor supply looks shorted to battery voltage, and sensor codes 21 to 2C may follow.· Shorted high
    Check soon

    Causes

    • Sensor supply wire shorted to battery voltage
    • A sensor failed and shorted the supply

    Checks

    1. 1Check the sensor supply wires and connectors for contact with supply
    2. 2Unplug sensors one at a time to see which one clears the fault
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Hyundai F1TCU general EEPROM fault

    The TCU cannot read its non volatile memory, though it carries on normally.· Part or controller
    Info

    Causes

    • TCU internal fault
    • Supply interruption during a write

    Checks

    1. 1Cycle power and see whether the fault returns
    2. 2Replace the TCU if it persists
    ControllerPartSupplySignalGround?
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Check power and ground at the module connector with the key on, then its fuses.

    Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

  • Hyundai D2TCU sensor power supply: short to ground

    The sensor supply looks shorted to ground, and sensor codes 21 to 2C may follow.· Shorted low
    Check soon

    Causes

    • Sensor supply wire shorted to ground
    • A sensor failing and pulling the supply down

    Checks

    1. 1Check the sensor supply wires and connectors for a path to ground
    2. 2Unplug sensors one at a time to find the short
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Hyundai F2TCU configuration lost

    The TCU has lost its correct configuration and the transmission stays in neutral until it is reprogrammed.· Other
    Stop now

    Causes

    • Configuration data lost after a TCU replacement or memory fault
    • Wrong TCU installed

    Checks

    1. 1Reprogram the correct configuration
    2. 2Check for a following F1 or F3
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Hyundai D3TCU low voltage at battery

    The voltage at the TCU supply is lower than allowed, so the TCU shifts to neutral.· Shorted low
    Stop now

    Causes

    • Weak battery or poor connections
    • Alternator not charging

    Checks

    1. 1Check the battery supply to the TCU
    2. 2Check the charging system
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Hyundai E3TCU display output: short to battery voltage

    The TCU sends data to the display and sees a short to battery voltage on that output.· Shorted high
    Info

    Causes

    • Display data wire touching battery voltage
    • Display fault

    Checks

    1. 1Check the display data wire
    2. 2Check the display connector
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Hyundai F3TCU application error

    Something in the TCU application is wrong and the transmission stays in neutral.· Other
    Stop now

    Causes

    • Wrong or damaged TCU program
    • TCU internal fault

    Checks

    1. 1Replace or reprogram the TCU
    2. 2Check the TCU part number
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Hyundai C4TCU joystick status indicator: short to ground

    The joystick status indicator output looks shorted to ground and the TCU takes no action.· Shorted low
    Info

    Causes

    • Indicator wire touching ground
    • Indicator lamp failed

    Checks

    1. 1Check the indicator wire for chafing
    2. 2Check the joystick connector
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Hyundai D4TCU high voltage at battery

    The voltage at the TCU supply is higher than allowed, so the TCU shifts to neutral.· Shorted high
    Stop now

    Causes

    • Alternator regulator overcharging
    • Wrong battery set

    Checks

    1. 1Check the battery supply to the TCU with a meter
    2. 2Check the alternator regulator
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Hyundai E4TCU display output: short to ground

    The TCU sends data to the display and sees a short to ground on that output.· Shorted low
    Info

    Causes

    • Display data wire touching ground
    • Display fault

    Checks

    1. 1Check the display data wire
    2. 2Check the display connector
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Hyundai C5TCU joystick status indicator: short to battery voltage

    The joystick status indicator output looks shorted to battery voltage and the TCU takes no action.· Shorted high
    Info

    Causes

    • Indicator wire touching battery voltage
    • Indicator lamp failed

    Checks

    1. 1Check the indicator wire for contact with supply
    2. 2Check the connector
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Hyundai D5TCU error at valve power supply VPS1

    The TCU switched on VPS1 and did not measure the expected result, so it shuts down and shifts to neutral.· Other
    Stop now

    Causes

    • Fuse for VPS1 blown
    • Wiring fault on VPS1

    Checks

    1. 1Check the VPS1 fuse
    2. 2Check the wiring on VPS1
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Hyundai E5TCU communication failure on DeviceNet

    The TCU lost the DeviceNet link and shifts to neutral and shuts down.· Other
    Stop now

    Causes

    • DeviceNet wiring fault
    • Master controller not responding

    Checks

    1. 1Check the DeviceNet cable and connectors
    2. 2Check the master controller
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Hyundai F5TCU clutch failure

    The AEB could not adjust the clutch filling and the transmission stays in neutral.· Other
    Stop now

    Causes

    • Clutch defective
    • Low pressure at a clutch during AEB

    Checks

    1. 1Check the clutch involved
    2. 2Repeat the AEB and check pressures
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Hyundai C6TCU joystick status indicator: open circuit

    The joystick status indicator output looks open and the TCU takes no action beyond the warning.· Open circuit
    Info

    Causes

    • Indicator wire open
    • Indicator lamp failed

    Checks

    1. 1Check the indicator wire for a break
    2. 2Check the connector
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Hyundai D6TCU error at valve power supply VPS2

    The TCU switched on VPS2 and did not measure the expected result, so it shuts down and shifts to neutral.· Other
    Stop now

    Causes

    • Fuse for VPS2 blown
    • Wiring fault on VPS2

    Checks

    1. 1Check the VPS2 fuse
    2. 2Check the wiring on VPS2
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Hyundai F6TCU clutch adjustment data lost

    The TCU could not read the stored clutch adjustment data after a TCU, valve block or transmission replacement.· Other
    Check soon

    Causes

    • Transmission, valve block or TCU replaced without running AEB
    • Stored clutch data lost
    • EEPROM write failed during a previous AEB

    Checks

    1. 1Run the AEB cycle with the shifter in neutral, engine at idle, parking brake applied and the transmission at working temperature
    2. 2Let the AEB cycle finish without touching the controls, since it needs three to four minutes
    3. 3Check that the F6 message is gone after the cycle and that gear shifts are smooth
    4. 4If F6 returns, read for F1 or F2 which would show the TCU memory is at fault
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Hyundai F7TCU substitute clutch control

    The TCU is using substitute clutch control, for example after a wrong input torque or a fault elsewhere.· Other
    Check soon

    Causes

    • Another fault forcing the substitute mode
    • Wrong input torque signal

    Checks

    1. 1Read the other codes that appeared with F7
    2. 2Check the engine retarder torque signal
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

Shared checks

Checks, in order

  1. 1Measure battery voltage at the TCU supply pin
  2. 2Check the fuses for the TCU and valve supplies with a meter
  3. 3Check the TCU connectors for corrosion and pushed-back pins
  4. 4Reprogram or reload the TCU configuration if it was lost
  5. 5Replace the TCU if internal faults return after the supply is proven good

Causes

  • Battery voltage low or high at the TCU
  • Fuse blown or supply wire damaged
  • TCU configuration lost or TCU failed
  • Display or joystick wiring fault

Most common here: shorted high (4 of 18)

Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

When to stop

You'll notice: The transmission may stay in neutral or the TCU may shut down, and the display shows a hex code such as D3 or F6.

Lower attachments to the ground and relieve hydraulic pressure before loosening any fitting. Never feel for a leak with your hand - oil under pressure can inject through skin.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.