Hyundai · Transmission TCU codes (hex)
Hyundai TCU CAN message and engine signal faults fault codes
The TCU depends on CAN messages from the engine controller, joystick steering and other controllers. These codes report a timeout of one message or a bad signal inside a message, such as engine torque or the downshift requests.
Where this code shows
Turn the key on and open the fault code or diagnosis menu on the cluster.
What do these codes mean?
Hyundai codes 5C to 69 are all about the tCU CAN message and engine signal faults. Most are lost message faults; none needs an immediate stop. Start with this check: check the CAN wiring and its connectors for corrosion and loose pins.
How urgent are they?
None of the 14 codes here means stop now; all 14 can wait until the shift ends, but find the cause before the next one.
- Check soon14
What should I check first?
Check the CAN wiring and its connectors for corrosion and loose pins
Shared checks14 of 14
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
Hyundai 5CTCU Auto downshift signal
The CAN signal for auto downshift is defective and the TCU takes no action on it. This is a driver request signal, so its failure removes one input and the TCU simply ignores it. Test the auto downshift switch and see whether the cluster shows its state changing. Check the switch wiring. Check the harness behind the selector panel for pinched wires.· Lost messageLost messageCheck soonCauses
- Fault in the CAN wiring or connectors
- Sending controller faulty
Checks
- 1Check the CAN bus wiring between the TCU and the sending controller
- 2Check the CAN wire for the auto downshift request
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Hyundai 5DTCU Manual downshift signal
The CAN signal for manual downshift is defective and the TCU takes no action on it. This is a driver request signal for manual downshift, so its failure removes one input and the TCU simply ignores it. Test the manual downshift switch or button and see whether its state changes on the cluster. Check the button wiring. Check the harness behind the lever knob for pinched wires.· Lost messageLost messageCheck soonCauses
- Fault in the CAN wiring or connectors
- Sending controller faulty
Checks
- 1Check the CAN bus wiring between the TCU and the sending controller
- 2Check the CAN wire for the manual downshift request
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Hyundai 5ETCU CCO request signal
The CAN signal for the clutch cut off request is defective and the TCU takes no action on it. This is the clutch cut off request from another controller, so its failure removes one input and the TCU simply ignores it. Test the clutch cut off switch and see whether its state changes on the cluster. Check the pedal switch wiring. Check the brake pedal switch bracket for movement.· Lost messageLost messageCheck soonCauses
- Fault in the CAN wiring or connectors
- Sending controller faulty
Checks
- 1Check the CAN bus wiring between the TCU and the sending controller
- 2Check the CAN wire for the clutch cut off request
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Hyundai 6ATCU Actual engine torque signal
The CAN signal for actual engine torque is defective, so the TCU uses substitute clutch control. Actual torque is the live engine output, so a defective signal forces the TCU into substitute clutch control. Look at the engine controller for actual torque output faults. Check the torque output. Look for derate states in the engine controller that alter output.· Lost messageLost messageCheck soonCauses
- Fault in the CAN wiring or connectors
- Sending controller faulty
Checks
- 1Check the CAN bus wiring between the TCU and the sending controller
- 2Check the actual torque message from the engine controller
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Hyundai 6ETCU EEC2 timeout
The TCU stopped receiving the EEC2 message and falls back to a default accelerator pedal signal. EEC2 carries accelerator pedal position, so with it missing the TCU runs on a default pedal value and shift points may be wrong. Press the accelerator pedal and see whether the cluster pedal position moves, because a frozen value confirms the message is lost. Check the pedal sensor wiring. A throttle pedal sensor fault feeding the engine controller can also stop this message.· Lost messageLost messageCheck soonCauses
- Fault in the CAN wiring or connectors
- Sending controller faulty
Checks
- 1Check the CAN bus wiring between the TCU and the sending controller
- 2Check the accelerator pedal position signal from the engine controller
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Hyundai 54TCU DCT1 timeout
The TCU stopped receiving the DCT1 CAN message. The DCT1 message is one of the controller-to-controller messages the TCU relies on, so its loss lets the TCU run on normal mode but with reduced information. Check which controller owns the DCT1 message on this machine and look at its connector first. Check the bus for stray connections. Stray resistance, unterminated stubs or a half-seated connector on the network are typical.· Lost messageLost messageCheck soonCauses
- Fault in the CAN wiring or connectors
- Sending controller faulty
Checks
- 1Check the CAN bus wiring between the TCU and the sending controller
- 2Check the wire of the CAN bus where DCT1 originates
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Hyundai 55TCU JSS timeout
The TCU stopped receiving the joystick steering CAN message and shifts to neutral if joystick steering is active. Joystick steering is a separate controller, so check that it is fitted and powered if the machine has it, and that its connector is seated. Try driving without joystick steering active to see whether the TCU recovers. Check that its termination is fitted. Only machines equipped with steering joysticks should show this fault.· Lost messageLost messageCheck soonCauses
- Fault in the CAN wiring or connectors
- Sending controller faulty
Checks
- 1Check the CAN bus wiring between the TCU and the sending controller
- 2Check the joystick steering controller and its CAN wiring
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Hyundai 56TCU Engine CONF timeout
The TCU stopped receiving the engine configuration CAN message and falls back to substitute clutch control. Engine configuration data is needed for torque limits, so with it missing the TCU runs conservatively in substitute clutch control. Cycle the key and see whether the engine controller sends its configuration message again after start. Check software levels on both controllers. A flashed or replaced engine controller with the wrong parameter file commonly triggers it.· Lost messageLost messageCheck soonCauses
- Fault in the CAN wiring or connectors
- Sending controller faulty
Checks
- 1Check the CAN bus wiring between the TCU and the sending controller
- 2Check that the engine controller sends its configuration message
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Hyundai 57TCU EEC1 timeout
The TCU stopped receiving the EEC1 message from the engine controller and uses substitute clutch control. EEC1 carries engine speed and torque, so losing it removes the main engine data the TCU uses to shape shifts. The engine speed on the cluster should keep updating; a frozen value confirms the message is lost. Check the bus for stray connections. A bus-off event in the engine controller or an overloaded network can drop the message.· Lost messageLost messageCheck soonCauses
- Fault in the CAN wiring or connectors
- Sending controller faulty
Checks
- 1Check the CAN bus wiring between the TCU and the sending controller
- 2Check the engine controller for power and its own codes
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Hyundai 58TCU EEC3 timeout
The TCU stopped receiving the EEC3 message from the engine controller and uses substitute clutch control. EEC3 carries engine data used for torque calculation, so losing it affects shift quality rather than driveability. Check whether other engine messages are still received, because a missing EEC3 alone points to the engine controller output. Check the connector for water. Weak battery supply during cranking can interrupt the message briefly.· Lost messageLost messageCheck soonCauses
- Fault in the CAN wiring or connectors
- Sending controller faulty
Checks
- 1Check the CAN bus wiring between the TCU and the sending controller
- 2Check the engine controller output for the EEC3 message
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Hyundai 61TCU AEB request signal
The CAN signal for the AEB request is defective and the TCU takes no action on it. The AEB request comes from another controller, so its failure means clutch calibration cannot be requested over the network. Look at the AEB menu and see whether the request can be started. Check the AEB wiring. Check that the service tool or menu is not holding the request open.· Lost messageLost messageCheck soonCauses
- Fault in the CAN wiring or connectors
- Sending controller faulty
Checks
- 1Check the CAN bus wiring between the TCU and the sending controller
- 2Check the CAN wire for the AEB request
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Hyundai 64TCU Starting gear signal
The CAN signal for starting gear is defective, so the TCU falls back to its default starting gear. Starting gear is chosen from the machine data, so a defective signal leaves the TCU on its default starting gear. Check the starting gear setting in the machine configuration if the display offers it. Check the gear selection wiring. Check the machine option setting for starting gear.· Lost messageLost messageCheck soonCauses
- Fault in the CAN wiring or connectors
- Sending controller faulty
Checks
- 1Check the CAN bus wiring between the TCU and the sending controller
- 2Check the CAN wire for the starting gear signal
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Hyundai 65TCU Engine torque signal
The CAN signal for engine torque is defective, so the TCU uses substitute clutch control. The torque value shapes clutch filling, so a defective signal forces the TCU into substitute clutch control. Look at the engine controller for its own torque signal faults. Check the torque message source. Look for engine-controller faults on the torque limit map.· Lost messageLost messageCheck soonCauses
- Fault in the CAN wiring or connectors
- Sending controller faulty
Checks
- 1Check the CAN bus wiring between the TCU and the sending controller
- 2Check the engine torque message from the engine controller
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Hyundai 69TCU Reference engine torque signal
The CAN signal for reference engine torque is defective, so the TCU uses substitute clutch control. Reference torque is the full-load figure for the engine, so a defective signal forces substitute clutch control. Look at the engine controller for reference torque setup faults. Check the reference torque setup. Look for a mismatched engine rating file in the controller.· Lost messageLost messageCheck soonCauses
- Fault in the CAN wiring or connectors
- Sending controller faulty
Checks
- 1Check the CAN bus wiring between the TCU and the sending controller
- 2Check the reference torque message from the engine controller
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Shared checks
Checks, in order
- 1Check the CAN wiring and its connectors for corrosion and loose pins
- 2Check supply voltage and ground at the controller that should send the message
- 3Measure CAN bus resistance with the power off
- 4Check that the engine configuration matches the machine
- 5Clear the code and see which message times out first
Causes
- CAN bus wiring or connector fault
- Engine controller not sending the message
- Terminating resistor or ground problem on the bus
- Sending controller faulty
Most codes here: lost message (14 of 14)
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
When to stop
You'll notice: The transmission may fall back to substitute clutch control or ignore a driver request, and the display shows a two character hex code.
Brake and steering faults are a safety issue on site. Chock the machine and keep it parked until the fault is found and the brakes are tested.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
