EF Logo

Hyundai · Transmission TCU codes (hex)

Hyundai TCU auxiliary output circuits fault codes

These codes cover TCU outputs other than the clutch valves: engine derating, the customer specific ride control function, the reverse warning relay, the starter interlock relay, the converter lock-up solenoid, the difflock or axle connection and the warning signal output.

FaultInfoA1Hyundai · TCU auxiliary output circuits
Code shows hereFAULTA1

Where this code shows

Turn the key on and open the fault code or diagnosis menu on the cluster.

What do these codes mean?

Hyundai codes A1 to 96 are all about the tCU auxiliary output circuits. The most common failure type is shorted high (7 of 21); none needs an immediate stop. Start with this check: check the wire and connector from the TCU to the affected device.

How urgent are they?

None of the 21 codes here means stop now; 21 are information only.

  • Info21

What should I check first?

Check the wire and connector from the TCU to the affected device

Shared checks

21 of 21

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Hyundai A1TCU difflock or axle connection: short to ground

    The difflock solenoid output looks shorted to ground.· Shorted low
    Info

    Causes

    • Fault in the wiring or connector of the difflock or axle connection
    • Difflock or axle connection coil or relay failed

    Checks

    1. 1Check the cable and connector for the difflock or axle connection
    2. 2Test the difflock or axle connection coil or relay resistance for the short to ground condition
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Hyundai A2TCU difflock or axle connection: short to battery voltage

    The difflock solenoid output looks shorted to battery voltage.· Shorted high
    Info

    Causes

    • Fault in the wiring or connector of the difflock or axle connection
    • Difflock or axle connection coil or relay failed

    Checks

    1. 1Check the cable and connector for the difflock or axle connection
    2. 2Test the difflock or axle connection coil or relay resistance for the short to battery voltage condition
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Hyundai A3TCU difflock or axle connection: open circuit

    The difflock solenoid output looks open.· Open circuit
    Info

    Causes

    • Fault in the wiring or connector of the difflock or axle connection
    • Difflock or axle connection coil or relay failed

    Checks

    1. 1Check the cable and connector for the difflock or axle connection
    2. 2Test the difflock or axle connection coil or relay resistance for the open circuit condition
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Hyundai A4TCU warning signal output: short to ground

    The warning signal output looks shorted to ground.· Shorted low
    Info

    Causes

    • Fault in the wiring or connector of the warning signal output
    • Warning signal output coil or relay failed

    Checks

    1. 1Check the cable and connector for the warning signal output
    2. 2Test the warning signal output coil or relay resistance for the short to ground condition
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Hyundai A5TCU warning signal output: open circuit

    The warning signal output looks open.· Open circuit
    Info

    Causes

    • Fault in the wiring or connector of the warning signal output
    • Warning signal output coil or relay failed

    Checks

    1. 1Check the cable and connector for the warning signal output
    2. 2Test the warning signal output coil or relay resistance for the open circuit condition
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Hyundai A6TCU warning signal output: short to battery voltage

    The warning signal output looks shorted to battery voltage.· Shorted high
    Info

    Causes

    • Fault in the wiring or connector of the warning signal output
    • Warning signal output coil or relay failed

    Checks

    1. 1Check the cable and connector for the warning signal output
    2. 2Test the warning signal output coil or relay resistance for the short to battery voltage condition
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Hyundai 7DTCU engine derating device: short to ground

    Engine derating stays on while the fault is present.· Shorted low
    Info

    Causes

    • Fault in the wiring or connector of the engine derating device
    • Engine derating device coil or relay failed

    Checks

    1. 1Check the cable and connector for the engine derating device
    2. 2Test the engine derating device coil or relay resistance for the short to ground condition
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Hyundai 7ETCU engine derating device: short to battery voltage

    The engine derating output looks shorted to battery voltage.· Shorted high
    Info

    Causes

    • Fault in the wiring or connector of the engine derating device
    • Engine derating device coil or relay failed

    Checks

    1. 1Check the cable and connector for the engine derating device
    2. 2Test the engine derating device coil or relay resistance for the short to battery voltage condition
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Hyundai 7FTCU engine derating device: open circuit

    The engine derating output looks open and the TCU keeps running normally.· Open circuit
    Info

    Causes

    • Fault in the wiring or connector of the engine derating device
    • Engine derating device coil or relay failed

    Checks

    1. 1Check the cable and connector for the engine derating device
    2. 2Test the engine derating device coil or relay resistance for the open circuit condition
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Hyundai 9ATCU converter lock-up clutch solenoid: short to ground

    The lock-up solenoid output looks shorted to ground.· Shorted low
    Info

    Causes

    • Fault in the wiring or connector of the converter lock-up clutch solenoid
    • Converter lock-up clutch solenoid coil or relay failed

    Checks

    1. 1Check the cable and connector for the converter lock-up clutch solenoid
    2. 2Test the converter lock-up clutch solenoid coil or relay resistance for the short to ground condition
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Hyundai 9BTCU converter lock-up clutch solenoid: open circuit

    The converter clutch stays open, which shows as lost lock-up and higher converter slip.· Open circuit
    Info

    Causes

    • Fault in the wiring or connector of the converter lock-up clutch solenoid
    • Converter lock-up clutch solenoid coil or relay failed

    Checks

    1. 1Check the cable and connector for the converter lock-up clutch solenoid
    2. 2Test the converter lock-up clutch solenoid coil or relay resistance for the open circuit condition
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Hyundai 9CTCU converter lock-up clutch solenoid: short to battery voltage

    The lock-up solenoid output looks shorted to battery voltage.· Shorted high
    Info

    Causes

    • Fault in the wiring or connector of the converter lock-up clutch solenoid
    • Converter lock-up clutch solenoid coil or relay failed

    Checks

    1. 1Check the cable and connector for the converter lock-up clutch solenoid
    2. 2Test the converter lock-up clutch solenoid coil or relay resistance for the short to battery voltage condition
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Hyundai 17TCU customer function 1 (ride control): short to ground

    The ride control output looks shorted to vehicle ground.· Shorted low
    Info

    Causes

    • Fault in the wiring or connector of the customer function 1 (ride control)
    • Customer function 1 (ride control) coil or relay failed

    Checks

    1. 1Check the cable and connector for the customer function 1 (ride control)
    2. 2Test the customer function 1 (ride control) coil or relay resistance for the short to ground condition
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Hyundai 18TCU customer function 1 (ride control): short to battery voltage

    The ride control output looks shorted to battery voltage.· Shorted high
    Info

    Causes

    • Fault in the wiring or connector of the customer function 1 (ride control)
    • Customer function 1 (ride control) coil or relay failed

    Checks

    1. 1Check the cable and connector for the customer function 1 (ride control)
    2. 2Test the customer function 1 (ride control) coil or relay resistance for the short to battery voltage condition
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Hyundai 19TCU customer function 1 (ride control): open circuit

    The ride control output looks open.· Open circuit
    Info

    Causes

    • Fault in the wiring or connector of the customer function 1 (ride control)
    • Customer function 1 (ride control) coil or relay failed

    Checks

    1. 1Check the cable and connector for the customer function 1 (ride control)
    2. 2Test the customer function 1 (ride control) coil or relay resistance for the open circuit condition
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Hyundai 91TCU reverse warning relay: short to ground

    The backup alarm stays on while the fault is present.· Shorted low
    Info

    Causes

    • Fault in the wiring or connector of the reverse warning relay
    • Reverse warning relay coil or relay failed

    Checks

    1. 1Check the cable and connector for the reverse warning relay
    2. 2Test the reverse warning relay coil or relay resistance for the short to ground condition
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Hyundai 92TCU reverse warning relay: short to battery voltage

    The reverse warning relay output looks shorted to battery voltage.· Shorted high
    Info

    Causes

    • Fault in the wiring or connector of the reverse warning relay
    • Reverse warning relay coil or relay failed

    Checks

    1. 1Check the cable and connector for the reverse warning relay
    2. 2Test the reverse warning relay coil or relay resistance for the short to battery voltage condition
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Hyundai 93TCU reverse warning relay: open circuit

    The reverse warning relay output looks open, so the alarm may not sound.· Open circuit
    Info

    Causes

    • Fault in the wiring or connector of the reverse warning relay
    • Reverse warning relay coil or relay failed

    Checks

    1. 1Check the cable and connector for the reverse warning relay
    2. 2Test the reverse warning relay coil or relay resistance for the open circuit condition
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Hyundai 94TCU starter interlock relay: short to ground

    The starter interlock relay output looks shorted to ground.· Shorted low
    Info

    Causes

    • Fault in the wiring or connector of the starter interlock relay
    • Starter interlock relay coil or relay failed

    Checks

    1. 1Check the cable and connector for the starter interlock relay
    2. 2Test the starter interlock relay coil or relay resistance for the short to ground condition
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Hyundai 95TCU starter interlock relay: short to battery voltage

    The starter interlock relay output looks shorted to battery voltage.· Shorted high
    Info

    Causes

    • Fault in the wiring or connector of the starter interlock relay
    • Starter interlock relay coil or relay failed

    Checks

    1. 1Check the cable and connector for the starter interlock relay
    2. 2Test the starter interlock relay coil or relay resistance for the short to battery voltage condition
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Hyundai 96TCU starter interlock relay: open circuit

    The starter interlock relay output looks open.· Open circuit
    Info

    Causes

    • Fault in the wiring or connector of the starter interlock relay
    • Starter interlock relay coil or relay failed

    Checks

    1. 1Check the cable and connector for the starter interlock relay
    2. 2Test the starter interlock relay coil or relay resistance for the open circuit condition
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

Shared checks

Checks, in order

  1. 1Check the wire and connector from the TCU to the affected device
  2. 2Measure the coil or relay resistance and compare it with a known-good one
  3. 3Look for contact to ground or battery voltage along the wire
  4. 4Check the fuse for the circuit with the key on
  5. 5Clear the code and then operate the function to confirm it works

Causes

  • Relay or solenoid coil open or shorted
  • Wire from the TCU to the device damaged
  • Connector corroded
  • Wire touching battery voltage or ground

Most common here: shorted high (7 of 21)

Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

When to stop

You'll notice: A function such as the backup alarm, ride control, lock-up or starter interlock may stop working or stay on, and the display shows a hex code.

Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.