EF Logo

Hyundai · Transmission TCU codes (hex)

Hyundai TCU temperature and speed sensor inputs fault codes

The TCU reads transmission sump temperature, retarder temperature and four speed signals: engine, turbine, internal and output. A short or open on one of these inputs, or a logical mismatch between speeds, produces a code.

FaultCheck3AHyundai · TCU temperature and speed sensor inputs
Code shows hereFAULT3A

Where this code shows

Turn the key on and open the fault code or diagnosis menu on the cluster.

What do these codes mean?

Hyundai codes 3A to 39 are all about the tCU temperature and speed sensor inputs. The most common failure type is shorted high (6 of 17); none needs an immediate stop. Start with this check: check the sensor cable and connectors from the TCU to the transmission for chafing and corrosion.

How urgent are they?

None of the 17 codes here means stop now; 13 can wait until the shift ends, but find the cause before the next one; 4 are information only.

  • Check soon13
  • Info4

What should I check first?

Check the sensor cable and connectors from the TCU to the transmission for chafing and corrosion

Shared checks

17 of 17

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Hyundai 3ATCU output speed input: short to battery voltage or open circuit

    The output speed input voltage is too high, so the TCU loses the signal (output speed is the shaft speed that the TCU uses for gear selection and vehicle speed).· Shorted high
    Check soon

    Causes

    • Output speed sensor cable shorted to battery voltage or open
    • Output speed sensor failed

    Checks

    1. 1Check the output speed sensor cable and connector
    2. 2Check the output speed sensor gap and condition
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Hyundai 3BTCU output speed input: short to ground

    The output speed input voltage is too low, so the TCU loses the signal (output speed is the shaft speed that the TCU uses for gear selection and vehicle speed).· Shorted low
    Check soon

    Causes

    • Output speed sensor cable shorted to ground
    • Output speed sensor failed

    Checks

    1. 1Check the output speed sensor cable for a path to ground
    2. 2Check the output sensor and its connector
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Hyundai 3CTCU logical error at output speed input

    The output speed reading is outside what the TCU can accept as plausible; output speed is the shaft speed that the TCU uses for gear selection and vehicle speed.· Lost message
    Check soon

    Causes

    • Output speed sensor gap wrong
    • Signal interference on the output speed cable

    Checks

    1. 1Check the output sensor gap against the manual
    2. 2Compare the output speed signal with the other speeds while running
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • Hyundai 3ETCU output speed zero does not fit the other speed signals

    The output speed reads zero while other speed signals show motion, so the TCU switches to a special gear selection mode.· Open circuit
    Check soon

    Causes

    • Output speed sensor failed or gap wrong
    • Output speed cable broken

    Checks

    1. 1Check the output speed sensor gap and cable
    2. 2Compare the output speed with turbine and internal speed while moving
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Hyundai 25TCU transmission sump temperature sensor: short to battery voltage or open circuit

    The measured voltage on the sump temperature input is too high, so the TCU keeps running but assumes a default sump temperature.· Shorted high
    Info

    Causes

    • Cable shorted to battery voltage or open
    • Sump temperature sensor failed

    Checks

    1. 1Check the cable and connector from the TCU to the temperature sensor
    2. 2Check the sump temperature sensor wire for a break or contact with supply
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Hyundai 26TCU transmission sump temperature sensor: short to ground

    The measured voltage on the sump temperature input is too low, so the TCU keeps running but assumes a default sump temperature.· Shorted low
    Info

    Causes

    • Cable shorted to vehicle ground
    • Sump temperature sensor failed

    Checks

    1. 1Check the cable and connector from the TCU to the temperature sensor
    2. 2Check the sump temperature sensor wire for chafing to the housing
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Hyundai 27TCU retarder temperature sensor: short to battery voltage or open circuit

    The measured voltage on the retarder temperature input is too high, so the TCU keeps running but assumes a default retarder temperature.· Shorted high
    Info

    Causes

    • Retarder temperature cable shorted to battery voltage or open
    • Retarder temperature sensor failed

    Checks

    1. 1Check the cable and connector from the TCU to the temperature sensor
    2. 2Check the retarder temperature sensor wire for a break or contact with supply
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Hyundai 28TCU retarder temperature sensor: short to ground

    The measured voltage on the retarder temperature input is too low, so the TCU keeps running but assumes a default retarder temperature.· Shorted low
    Info

    Causes

    • Retarder temperature cable shorted to ground
    • Retarder temperature sensor failed

    Checks

    1. 1Check the cable and connector from the TCU to the temperature sensor
    2. 2Check the retarder temperature sensor wire for chafing to ground
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Hyundai 31TCU engine speed input: short to battery voltage or open circuit

    The engine speed input voltage is too high, so the TCU loses the signal (engine speed is the input side of the converter and the TCU compares it with turbine speed to judge converter slip).· Shorted high
    Check soon

    Causes

    • Engine speed sensor cable shorted to battery voltage or open
    • Engine speed sensor failed

    Checks

    1. 1Check the engine speed sensor cable and connector
    2. 2Check the engine speed sensor gap and condition
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Hyundai 32TCU engine speed input: short to ground

    The engine speed input voltage is too low, so the TCU loses the signal (engine speed is the input side of the converter and the TCU compares it with turbine speed to judge converter slip).· Shorted low
    Check soon

    Causes

    • Engine speed sensor cable shorted to ground
    • Engine speed sensor failed

    Checks

    1. 1Check the engine speed sensor cable for a path to ground
    2. 2Check the engine sensor and its connector
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Hyundai 33TCU logical error at engine speed input

    The engine speed reading is outside what the TCU can accept as plausible; engine speed is the input side of the converter and the TCU compares it with turbine speed to judge converter slip.· Lost message
    Check soon

    Causes

    • Engine speed sensor gap wrong
    • Signal interference on the engine speed cable

    Checks

    1. 1Check the engine sensor gap against the manual
    2. 2Compare the engine speed signal with the other speeds while running
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • Hyundai 34TCU turbine speed input: short to battery voltage or open circuit

    The turbine speed input voltage is too high, so the TCU loses the signal (turbine speed is the converter output and tells the TCU how fast the gearbox input is turning).· Shorted high
    Check soon

    Causes

    • Turbine speed sensor cable shorted to battery voltage or open
    • Turbine speed sensor failed

    Checks

    1. 1Check the turbine speed sensor cable and connector
    2. 2Check the turbine speed sensor gap and condition
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Hyundai 35TCU turbine speed input: short to ground

    The turbine speed input voltage is too low, so the TCU loses the signal (turbine speed is the converter output and tells the TCU how fast the gearbox input is turning).· Shorted low
    Check soon

    Causes

    • Turbine speed sensor cable shorted to ground
    • Turbine speed sensor failed

    Checks

    1. 1Check the turbine speed sensor cable for a path to ground
    2. 2Check the turbine sensor and its connector
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Hyundai 36TCU logical error at turbine speed input

    The turbine speed reading is outside what the TCU can accept as plausible; turbine speed is the converter output and tells the TCU how fast the gearbox input is turning.· Lost message
    Check soon

    Causes

    • Turbine speed sensor gap wrong
    • Signal interference on the turbine speed cable

    Checks

    1. 1Check the turbine sensor gap against the manual
    2. 2Compare the turbine speed signal with the other speeds while running
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • Hyundai 37TCU internal speed input: short to battery voltage or open circuit

    The internal speed input voltage is too high, so the TCU loses the signal (internal speed is the gearbox shaft speed the TCU uses to judge clutch slip).· Shorted high
    Check soon

    Causes

    • Internal speed sensor cable shorted to battery voltage or open
    • Internal speed sensor failed

    Checks

    1. 1Check the internal speed sensor cable and connector
    2. 2Check the internal speed sensor gap and condition
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Hyundai 38TCU internal speed input: short to ground

    The internal speed input voltage is too low, so the TCU loses the signal (internal speed is the gearbox shaft speed the TCU uses to judge clutch slip).· Shorted low
    Check soon

    Causes

    • Internal speed sensor cable shorted to ground
    • Internal speed sensor failed

    Checks

    1. 1Check the internal speed sensor cable for a path to ground
    2. 2Check the internal sensor and its connector
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Hyundai 39TCU logical error at internal speed input

    The internal speed reading is outside what the TCU can accept as plausible; internal speed is the gearbox shaft speed the TCU uses to judge clutch slip.· Lost message
    Check soon

    Causes

    • Internal speed sensor gap wrong
    • Signal interference on the internal speed cable

    Checks

    1. 1Check the internal sensor gap against the manual
    2. 2Compare the internal speed signal with the other speeds while running
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

Shared checks

Checks, in order

  1. 1Check the sensor cable and connectors from the TCU to the transmission for chafing and corrosion
  2. 2Check the speed sensor gap and sensor face for damage or metal debris
  3. 3Check the sensor resistance or signal against a known-good sensor
  4. 4Look for a short to ground or battery voltage along the cable run
  5. 5Clear the code and see whether it comes back with the engine running

Causes

  • Speed sensor gap wrong or sensor damaged
  • Sensor cable chafed or connector corroded
  • Temperature sensor failed
  • A wiring short to ground or battery voltage

Most common here: shorted high (6 of 17)

Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

When to stop

You'll notice: Shifting may become harsh, the TCU may fall back to substitute clutch control or a special gear selection mode, and the display shows a two character hex code.

Let the engine cool before opening the cooling system; a hot cap releases scalding coolant. Running on with an overheat warning risks a head gasket or seized engine.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.