Kubota · Loader controller (E:0xx)
Kubota Fault Code E:004
Hydraulic oil temperature advance warning
What does Kubota code E:004 mean?
The hydraulic oil temperature is climbing toward its limit and the loader warns you before it gets there. If work continues the code moves on to E:005 and the machine starts protecting itself. Urgency: check soon - the machine may derate or limit a function. Check first: park, idle the engine and inspect the cooler core from both sides; blow out any packed debris with air.
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Park, idle the engine and inspect the cooler core from both sides; blow out any packed debris with air
Then 4 more checksWhere this code shows
Watch the meter panel: a warning lamp comes on and the E: code scrolls on the display.
Checks
0 of 5 done
Causes
- Oil cooler fins packed with dirt, chaff or debris
- Cooling fan or its speed solenoid not reaching full speed
- Hydraulic oil level low or oil too thin after a long hot shift
- Circuit relieving constantly because an attachment is held at the end of its stroke
How it failed
You'll notice: Oil temperature warning on the meter with E:004; the loader still works at full strength but is heating up.
OtherRead from how the source describes the code
The source does not say how this one failed.
- Meter test
- Read the code with the service tool and note which other codes are active with it.
- Good result
- Codes that appear together usually share one cause - start with the wiring they share.
When to stop
Lower attachments to the ground and relieve hydraulic pressure before loosening any fitting. Never feel for a leak with your hand - oil under pressure can inject through skin.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Loader hydraulic controls and solenoids
- E:004Hydraulic oil temperature advance warningOtherCheck soon
- E:005Hydraulic oil temperature reached specified levelOtherStop now
- E:010High-speed switching system errorOtherCheck soon
- E:014High-flow system errorLost messageCheck soon
- E:015Hydraulic quick-hitch system errorOtherCheck soon
- E:016Auxiliary hydraulic control error (knob control switch)OtherCheck soon
- E:018Auxiliary hydraulic control error (rightward switch solenoid valve)OtherCheck soon
- E:019Auxiliary hydraulic control error (leftward switch solenoid valve)OtherCheck soon
- E:024Hydraulic oil temperature sensor errorOtherCheck soon
Show the other 7 codesHide the other codes
- E:027Ride control solenoid broken or short-circuitedOpen circuitCheck soon
- E:029Hydraulic lock solenoid (arm) broken or short-circuitedShort circuitCheck soon
- E:030Hydraulic lock solenoid (bucket) broken or short-circuitedLost messageCheck soon
- E:031High-speed mode pressure sensor broken or short-circuitedShort circuitCheck soon
- E:032Float mode selector solenoid cable broken or short-circuitedShort circuitCheck soon
- E:036Forward detection pressure sensor (right) cable brokenOtherCheck soon
- E:037Forward detection pressure sensor (left) cable brokenOtherCheck soon
Other Kubota codes: Loader controller (E:0xx)
Related on Equipments Finder
Source
This source lists E:004 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Kubota SSV65, SSV75, SVL65-2, SVL75-3, SVL97-2 loaders (the models the source lists).
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
