Volvo/Mack · MID 128 engine ECU - aftertreatment (DPF, DEF, NOx)
Volvo/Mack Fault Code MID 128 PPID 326 FMI 11
DPF soot level critically high
What does Volvo/Mack code MID 128 PPID 326 FMI 11 mean?
The soot load in the DPF is critically high. Mack lists a clogged DPF, a hydrocarbon doser fault and regeneration being disabled. Urgency: stop now - shut down and fix before working on. Check first: do not keep driving under load; arrange a service regeneration first.
- MID 128
- Which control unit reports it
- PPID 326
- Maker parameter at fault
- FMI 11
- Root cause not known
Can I keep running with it?
Stop now
Shut down and fix before working on. Running on risks damage or the machine locks out.
What should I check first?
Do not keep driving under load; arrange a service regeneration first
Then 3 more checksWhere to read it
Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.
Checks
0 of 4 done
Causes
- Diesel particulate filter clogged
- Aftertreatment hydrocarbon doser failure
- Regeneration disabled by the driver or another component
How it failed
You'll notice: Red stop lamp lit, heavy engine derate.
Real conditionRead from FMI 11: root cause not known
The sensor reading is valid but outside the allowed range - the problem may be real.
- Meter test
- Check the real value with a separate gauge or thermometer before blaming the sensor.
- Good result
- If the gauge agrees with the display, fix the machine, not the sensor.
When to stop
Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: DPF soot level
1 other code on this part is also real condition (MID 128 PPID 326 FMI 0). When they show together, start at the wiring and connector they share.
- MID 128 PPID 326 FMI 0DPF soot level moderately highReal conditionCheck soon
- MID 128 PPID 326 FMI 11DPF soot level critically highReal conditionStop now
Other Volvo/Mack codes: MID 128 engine ECU - aftertreatment (DPF, DEF, NOx)
- MID 128 PSID 46 FMI 0SCR system severe fault - operator inducement
- MID 128 PSID 47 FMI 0Unable to reach regeneration temperature
- MID 128 PSID 47 FMI 1Aftertreatment temperature too high during regeneration
- MID 128 PID 81 FMI 0DPF differential pressure critically high
- MID 128 PID 81 FMI 3DPF differential pressure sensor signal high
- MID 128 PID 81 FMI 5DPF differential pressure sensor circuit open
- MID 128 PSID 90 FMI 1DEF dosing too low - NOx limits exceeded, poor DEF quality
Related on Equipments Finder
Source
This source lists MID 128 PPID 326 FMI 11 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Mack MP7/MP8/MP10 engines (CHU, CXU, GU, TD) with the 2010-and-later MID 128 engine ECU; the same MID 128 numbers appear on Volvo D11/D13 engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
