Komatsu · Engine controller
Komatsu Throttle sensor and its supply fault codes
The throttle (fuel control dial) sensor tells the engine controller the engine speed the operator wants. It is a potentiometer on a 5 V feed with its own supply circuit.
More about these partsLess
A fault here makes the engine ignore the dial or hold a fixed speed.
Where this code shows
Watch the monitor for the user code and the caution lamp or buzzer, and write the code down.
What do these codes mean?
Komatsu codes CA131 to CA2186 are all about the throttle sensor and its supply. The most common failure type is shorted high (2 of 4); none needs an immediate stop. Start with this check: look at the throttle dial connector for water and bent pins.
How urgent are they?
None of the 4 codes here means stop now; all 4 can wait until the shift ends, but find the cause before the next one.
- Check soon4
What should I check first?
Look at the throttle dial connector for water and bent pins
Shared checksStop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
Komatsu CA131Throttle sensor: high voltage
The engine controller sees the throttle sensor signal voltage above its allowed range and treats the reading as unusable. It falls back to a default value, which can limit the function that depends on this input.· Shorted highShorted highCheck soonCauses
- Signal wire of the throttle sensor shorted to a 5 V or battery feed
- Open ground return at the throttle sensor, letting the signal float high
- Failed potentiometer reading full travel
Checks
- 1Unplug the throttle sensor connector and measure the signal wire to ground with key on; a high reading with the sensor off points to the harness
- 2Turn the dial while watching the signal on the monitor service mode and look for a stuck high value
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Komatsu CA132Throttle sensor: low voltage
The engine controller sees the throttle sensor signal voltage below its allowed range and discards the reading. It works from a substitute value, so engine response or protection logic tied to this input may be reduced.· Shorted lowShorted lowCheck soonCauses
- Signal wire of the throttle sensor shorted to ground or rubbed through on the engine harness
- Open signal wire or a pin pushed back in the throttle sensor connector
- Failed potentiometer reading zero travel
Checks
- 1Unplug the throttle sensor connector and measure the signal wire to ground; a near-zero reading with the sensor off means the harness is shorted
- 2Turn the dial while watching the signal on the monitor service mode and look for a stuck low value
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Komatsu CA2185Throttle sensor power supply: high voltage
The 5 V supply that powers the throttle (fuel dial) sensor is above its allowed range. The engine controller cannot trust the dial position, so engine speed may not follow the dial or may go to a default.· Shorted highShorted highCheck soonCauses
- Throttle supply wire touching a 12 V or 24 V line
- Controller supply output fault feeding the throttle circuit
- Water in the throttle sensor connector bridging the supply to another wire
Checks
- 1Unplug the throttle sensor and measure the supply wire to ground with key on; it should be about 5 V, not battery voltage
- 2Check the throttle supply wire along the cab harness for contact with a power line
- 3Inspect the throttle sensor connector for water and corrosion
- 4Compare with the sensor supply 1 and 2 readings to see whether only the throttle supply is high
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Komatsu CA2186Throttle sensor power supply: low voltage
The 5 V supply that powers the throttle (fuel dial) sensor is below its allowed range. The engine controller cannot trust the dial position, so engine speed may not follow the dial or may drop to idle.· Shorted lowShorted lowCheck soonCauses
- Throttle sensor shorted and pulling the supply down
- Throttle supply wire shorted to ground or rubbed through
- Open supply wire or loose pin at the throttle connector
Checks
- 1Unplug the throttle sensor and see whether the supply returns to about 5 V
- 2Measure the throttle supply wire to ground with the sensor unplugged; low means the harness is shorted
- 3Check the throttle supply wire continuity back to the engine controller
- 4Inspect the throttle sensor connector for pushed-back pins and water
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Shared checks
Checks, in order
- 1Look at the throttle dial connector for water and bent pins
- 2Unplug the sensor and measure the supply and signal wires with key on
- 3Turn the dial slowly and watch the monitor reading or voltage for jumps
- 4Check the harness between cab and engine for rubbed spots
Causes
- Dial or sensor connector corroded after washing
- Supply or signal wire rubbed through in the cab harness
- Worn track inside the potentiometer
- Throttle supply wire touching another feed
Most common here: shorted high (2 of 4)
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
When to stop
You'll notice: Engine speed does not follow the fuel dial, stays at a fixed speed or idles only, with the engine warning on the monitor (user code E14 in the SINOCMP table).
Most sensor and wiring faults can be traced with a multimeter and the wiring diagram. Disconnect the battery before unplugging controllers; if the controller itself is suspect or needs programming, that needs the dealer’s service tool.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
- SINOCMP - Error Code List for Komatsu PC200-8, PC220-8 and PC220LC-8 Excavators (failure code table)
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
