Komatsu · Engine controller
Komatsu Engine fluid, filter and temperature warnings fault codes
These monitor warnings come from engine and hydraulic sensors: air filter restriction, engine oil pressure and level, coolant temperature and level, hydraulic oil temperature, oil pressure switch and the water-in-fuel sensor. The monitor tells the operator to stop or fix the problem soon.
Where this code shows
Watch the monitor for the user code and the caution lamp or buzzer, and write the code down.
What do these codes mean?
Komatsu codes B@BAZG to CA435 are all about the engine fluid, filter and temperature warnings. The most common failure type is shorted high (3 of 9); 3 need an immediate stop. Start with this check: check the real condition first: oil level, coolant level, filter state and temperature by gauge.
How urgent are they?
3 of 9 codes here mean stop now; the other 6 can wait until the shift ends, but find the cause before the next one.
- Stop now3
- Check soon6
What should I check first?
Check the real condition first: oil level, coolant level, filter state and temperature by gauge
Shared checks9 of 9
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
Komatsu B@BAZGEngine oil pressure low
The engine oil pressure is below the allowed value for the speed. Running on may destroy the bearings, so stop the engine.· OtherOtherStop nowCauses
- Low engine oil level
- Worn oil pump or bearings
- Clogged oil filter
- Failed oil pressure switch or wiring
Checks
- 1Stop the engine and check the oil level and filter condition
- 2Fit a mechanical gauge at the test point to confirm real pressure before replacing the switch
- 3Check the oil pressure switch connector and its wiring for oil and breaks
- 4Look for fuel dilution or foaming oil on the dipstick
- 5If real pressure is low with good oil, inspect the oil pump and bearings
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Komatsu B@BAZKEngine oil level low
The oil level switch reports the engine oil level below the lower limit. Top up before running further.· OtherOtherCheck soonCauses
- Oil level genuinely low from a leak or consumption
- Oil level sensor connector loose
- Failed level sensor
Checks
- 1Check the dipstick level on level ground and top up
- 2Check for leaks around the pan, gasket and turbocharger lines
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Komatsu B@BCNSEngine coolant overheating
The engine coolant temperature went above the limit. Keep running and the head can crack or the gasket blow, so stop the engine and let it idle down first.· Shorted highShorted highStop nowCauses
- Low coolant level or leak
- Blocked radiator or oil cooler fins
- Fan drive or belt not working
- Failed thermostat
- Failed temperature sensor
Checks
- 1Let the engine idle to cool, then check the coolant level when it is safe to do so
- 2Clean the radiator and cooler fins and check the fan belt and fan speed
- 3Check that the thermostat opens at its rated temperature
- 4Compare the monitor temperature with an infrared thermometer
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Komatsu B@BCZKEngine coolant level low
The coolant level sensor reports the level below the lower limit. Low coolant can lead to overheating soon.· Lost messageLost messageCheck soonCauses
- Coolant leak at hoses, radiator or water pump
- Coolant not topped up after service
- Level sensor fault
Checks
- 1Check the coolant level in the radiator and reserve tank when cold
- 2Look for leaks at hoses, radiator, water pump and heater lines
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
Komatsu B@HANSHydraulic oil overheating
The hydraulic oil temperature went above the limit. Hot oil wears pumps and seals and thins out, so reduce load and let the oil cool.· Shorted highShorted highStop nowCauses
- Blocked oil cooler or radiator
- Fan not running correctly
- Hydraulic relief valve opening continuously
- Failed oil temperature sensor
Checks
- 1Clean the oil cooler and check the fan operation
- 2Check for a work pattern that keeps the machine at relief, such as holding a cylinder at end of stroke
- 3Compare the monitor temperature with a trusted thermometer
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Komatsu AA10NXAir filter clogged
The air cleaner restriction switch reports a clogged filter element. Continued operation starves the engine of air, causing black smoke and power loss.· Real conditionReal conditionCheck soonCauses
- Dirty or oil-soaked air filter element
- Dust pre-cleaner blocked
- Restriction switch or wiring fault
Checks
- 1Inspect and clean or replace the air filter element following the maintenance schedule
- 2Check the restriction switch connector and wiring
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Komatsu CA428Water in fuel sensor: high voltage
The water-in-fuel sensor in the fuel separator is reporting a voltage above range. It may mean water is present in the fuel, or the sensor or its wiring has failed.· Shorted highShorted highCheck soonCauses
- Water collected in the fuel separator bowl
- Water sensor wire open or loose
- Sensor failed
- Contaminated fuel from the tank
Checks
- 1Drain the water from the fuel separator and see whether the code clears
- 2Check the water sensor connector and wiring for corrosion and open wires
- 3Inspect the fuel tank bottom for water and sediment
- 4Replace the fuel filters if water has been present, then clear the code
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Komatsu CA429Water in fuel sensor: low voltage
The water-in-fuel sensor signal is below range. It points to a shorted sensor wire or a failed sensor.· Shorted lowShorted lowCheck soonCauses
- Sensor wire shorted to ground
- Failed water sensor
Checks
- 1Unplug the water sensor and measure the signal wire to ground
- 2Replace the sensor if the wiring is good
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Komatsu CA435Engine oil pressure switch error
The engine oil pressure switch signal does not match the engine state. Either the switch or its wiring is faulty, or the oil pressure is not building as it should.· OtherOtherCheck soonCauses
- Failed oil pressure switch
- Switch wire open or shorted
- Real low oil pressure
Checks
- 1Fit a mechanical gauge to confirm oil pressure
- 2Check the oil pressure switch connector and its wiring for oil and breaks
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
Shared checks
Checks, in order
- 1Check the real condition first: oil level, coolant level, filter state and temperature by gauge
- 2Inspect the sensor connector for oil and corrosion
- 3Compare the monitor reading with a trusted gauge or thermometer
- 4Look for leaks on the ground and engine that explain a low level
- 5Clear the code and see whether it returns once the real condition is corrected
Causes
- Low fluid level or dirty filter that the sensor is correctly reporting
- Loose or oily sensor connector
- Failed sensor or switch
- Blocked radiator, oil cooler or fan problems for temperature warnings
Most common here: shorted high (3 of 9)
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
When to stop
You'll notice: The monitor shows the warning symbol and a failure code, and the buzzer may sound.
Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
- Komatsu Error Code List (PC200-6/PC300-6/PC400-6/PC200-7 user and service codes, PC200-8 failure code index)
- Komatsu Fault Codes List (SlideShare, PC200-8 user and failure codes)
- SINOCMP - Error Code List for Komatsu PC200-8, PC220-8 and PC220LC-8 Excavators (failure code table)
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
