EF Logo

Komatsu · Engine controller

Komatsu Engine Ne and backup speed sensors fault codes

The engine controller reads crankshaft speed from the Ne sensor and camshaft position from the backup (Bkup) sensor. It needs both to time the common rail injectors.

More about these parts

If one fails the engine can usually run on the other; if both fail it stops.

FaultStopCA115Komatsu · Engine Ne and backup speed sensors
Code shows hereFAULTCA115

Where this code shows

Watch the monitor for the user code and the caution lamp or buzzer, and write the code down.

What do these codes mean?

Komatsu codes CA115 to CA778 are all about the engine Ne and backup speed sensors. The most common failure type is lost message (2 of 5); 1 needs an immediate stop. Start with this check: check both speed sensor connectors for pushed-back pins, oil and corrosion before changing parts.

How urgent are they?

1 of 5 codes here means stop now; the other 4 can wait until the shift ends, but find the cause before the next one.

  • Stop now1
  • Check soon4

What should I check first?

Check both speed sensor connectors for pushed-back pins, oil and corrosion before changing parts

Shared checks

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Komatsu CA115Engine Ne and Bkup speed sensor error

    The engine controller lost the signal from both the Ne (crankshaft) and the backup (camshaft) speed sensors at the same time.· Other
    Stop now

    Causes

    • Common ground or shield wire shared by both speed sensors is open
    • Both sensor connectors loose, oily or corroded after a wash
    • Harness crushed between the engine block and a bracket
    • Low sensor supply or an input fault inside the engine controller

    Checks

    1. 1Check that both speed sensor connectors are fully locked and free of oil before anything else
    2. 2Measure the resistance of each sensor at its plug and compare the two; a big difference shows which side failed
    3. 3Back-probe the shared sensor ground at the engine controller and confirm it is continuous to the engine block
    4. 4Inspect the harness at the block clamps and near the flywheel housing for rubbed-through wires
    5. 5Crank the engine with the monitor in service mode and note whether engine speed shows any value
    6. 6If wiring and both sensors pass, check controller supply and ground, then suspect the engine controller
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Komatsu CA238Ne speed sensor power supply voltage error

    The supply voltage feeding the Ne speed sensor is outside its allowed range.· Other
    Check soon

    Causes

    • Sensor supply wire shorted to ground or to another feed
    • Open supply wire or pin at the Ne sensor connector
    • Fault in the engine controller output for that supply

    Checks

    1. 1Unplug the Ne sensor and measure the supply wire to ground with key on
    2. 2Check the supply wire continuity back to the controller connector
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Komatsu CA689Engine Ne speed sensor error

    The signal from the Ne (crankshaft) speed sensor is lost or erratic.· Lost message
    Check soon

    Causes

    • Ne sensor connector loose or full of oil
    • Sensor tip dirty or air gap changed after a repair
    • Ne signal wire open or touching its neighbour

    Checks

    1. 1Unplug the Ne sensor and measure coil resistance, then compare it with the shop manual value
    2. 2Pull the Ne sensor and look at the tip for swarf, damage and a missing spacer
    3. 3Check the Ne sensor wires for continuity and for contact with ground at the engine harness
    4. 4Crank the engine in service mode and watch whether engine speed appears from the Ne sensor
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • Komatsu CA731Engine Bkup speed sensor phase error

    The backup sensor pulses arrive out of step with the Ne sensor pulses.· Other
    Check soon

    Causes

    • Sensor wires for Ne and Bkup swapped or crossed after a repair
    • Wrong reluctor or gear timing after a cam or gear repair
    • Loose or misaligned backup sensor

    Checks

    1. 1Check Ne and Bkup connector wiring against the diagram if the harness or sensors were recently changed
    2. 2Verify the cam gear is installed in its timed position after any timing-cover work
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Komatsu CA778Engine Bkup speed sensor error

    The backup (camshaft) speed sensor signal is missing or erratic.· Lost message
    Check soon

    Causes

    • Backup sensor connector loose, oily or corroded
    • Sensor spacing changed or tip contaminated
    • Backup sensor wire open, shorted or chafed near the cylinder head

    Checks

    1. 1Unplug the backup sensor and measure coil resistance, then compare it with the shop manual value
    2. 2Inspect the sensor tip and the cam gear it reads for damage
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

Shared checks

Checks, in order

  1. 1Check both speed sensor connectors for pushed-back pins, oil and corrosion before changing parts
  2. 2Measure the sensor coil resistance at its plug and compare it with the shop manual value for your serial number
  3. 3Inspect each sensor tip for metal swarf, damage and correct seating in its bore
  4. 4Inspect the harness along the block and the sensor shield ground for chafing
  5. 5Crank the engine with the monitor in service mode and note whether any engine speed shows at all

Causes

  • Damaged or oily connector at the Ne or Bkup sensor on the flywheel housing or timing cover
  • Sensor air gap changed or metal debris on the sensor tip
  • Harness rubbed through near the block or injector wiring
  • Damaged reluctor wheel or gear after a repair

Most common here: lost message (2 of 5)

Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

When to stop

You'll notice: Engine is hard to start, runs rough or surges, or stalls, with a CA code and the engine warning on the monitor.

Common-rail fuel runs at very high pressure. Never open a high-pressure line or fitting with the engine running or just after it stops - a fine fuel jet can pierce skin.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.