EF Logo

Komatsu · Engine controller

Komatsu Common rail fuel pressure fault codes

The common rail stores high pressure fuel for the injectors. A rail pressure sensor tells the engine controller the pressure and the controller regulates it by metering fuel into the supply pump with the IMV valve.

More about these parts

The codes cover the sensor signal and a rail pressure that is too high or too low.

FaultStopCA449Komatsu · Common rail fuel pressure
Code shows hereFAULTCA449

Where this code shows

Watch the monitor for the user code and the caution lamp or buzzer, and write the code down.

What do these codes mean?

Komatsu codes CA449 to CA2249 are all about the common rail fuel pressure. The most common failure type is real condition (3 of 6); 2 need an immediate stop. Start with this check: change the fuel filters and drain water from the separator before testing further.

How urgent are they?

2 of 6 codes here mean stop now; the other 4 can wait until the shift ends, but find the cause before the next one.

  • Stop now2
  • Check soon4

What should I check first?

Change the fuel filters and drain water from the separator before testing further

Shared checks

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Komatsu CA449Common rail pressure too high (stage 2)

    The measured rail pressure went above the upper limit.· Shorted high
    Stop now

    Causes

    • IMV valve stuck closed so the supply pump over-delivers
    • Pressure limiter valve stuck
    • Rail pressure sensor reading lower than the real pressure
    • Damaged IMV connector or harness

    Checks

    1. 1Read rail pressure in service mode and compare it with the commanded value
    2. 2Check the IMV connector and measure its coil resistance against the shop manual value
    3. 3Inspect the pressure limiter and return line for restriction
    4. 4Compare the sensor reading with a second pressure gauge if the manual provides a test point
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Komatsu CA451Common rail pressure sensor: high voltage

    The engine controller sees the common rail pressure sensor signal voltage above its allowed range and treats the reading as unusable.· Shorted high
    Check soon

    Causes

    • Signal wire of the common rail pressure sensor shorted to a 5 V or battery feed
    • Open ground return at the common rail pressure sensor, letting the signal float high
    • Failed rail pressure sensor reading above range

    Checks

    1. 1Unplug the common rail pressure sensor connector and measure the signal wire to ground with key on; a high reading with the sensor off points to the harness
    2. 2Compare the sensor reading in service mode with the cranking pressure; a high stuck value means the sensor or harness
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Komatsu CA452Common rail pressure sensor: low voltage

    The engine controller sees the common rail pressure sensor signal voltage below its allowed range and discards the reading.· Shorted low
    Check soon

    Causes

    • Signal wire of the common rail pressure sensor shorted to ground or rubbed through on the engine harness
    • Open signal wire or a pin pushed back in the common rail pressure sensor connector
    • Failed rail pressure sensor reading below range

    Checks

    1. 1Unplug the common rail pressure sensor connector and measure the signal wire to ground; a near-zero reading with the sensor off means the harness is shorted
    2. 2Compare the sensor reading in service mode with the cranking pressure; a zero stuck value means the sensor or harness
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Komatsu CA553Common rail pressure too high (stage 1)

    The rail pressure went above the first limit.· Real condition
    Check soon

    Causes

    • IMV valve sticking partly closed
    • Rail pressure sensor reading low
    • Restricted fuel return line

    Checks

    1. 1Compare commanded and actual rail pressure in service mode
    2. 2Check the fuel return line for kinks and blockage
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Komatsu CA559Common rail pressure too low (stage 1)

    The rail pressure stays below the commanded value.· Real condition
    Check soon

    Causes

    • Restricted fuel filter or air in the low pressure line
    • Worn supply pump
    • Leaking injector or rail connection
    • IMV valve stuck open
    • Water in the fuel

    Checks

    1. 1Change the fuel filters and bleed the low pressure circuit before further tests
    2. 2Check the supply line, fuel pump priming pump and tank pickup for suction leaks
    3. 3Read rail pressure in service mode while cranking
    4. 4Inspect rail, pipes and injector connections for fuel leaks
    5. 5If pressure is still low after these checks, test the supply pump delivery
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Komatsu CA2249Common rail pressure too low (stage 2)

    The rail pressure is far below the commanded value, below the second limit.· Real condition
    Stop now

    Causes

    • Severe fuel starvation from a blocked filter, empty tank or suction leak
    • Failed supply pump
    • Large injector or rail leak
    • IMV valve stuck open

    Checks

    1. 1Check the fuel level and filters, then the low pressure supply
    2. 2Look for fuel leaks at the rail, pipes and injectors
    3. 3Read rail pressure in service mode during cranking
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

Shared checks

Checks, in order

  1. 1Change the fuel filters and drain water from the separator before testing further
  2. 2Check the low pressure fuel line for suction leaks and air with a clear hose
  3. 3Read rail pressure in monitor service mode while cranking and at idle
  4. 4Check the rail pressure sensor connector and wires
  5. 5Perform the injector leak-off or return flow check described in the shop manual

Causes

  • Restricted fuel filter or supply line, or air in the fuel
  • Weak supply pump or leaking injector letting rail pressure bleed away
  • Sticking IMV valve or pressure limiter
  • Failed rail pressure sensor or damaged connector

Most common here: real condition (3 of 6)

Check the real value with a separate gauge or thermometer before blaming the sensor.

When to stop

You'll notice: Hard starting, loss of power, rough running or engine stalling, with the engine warning on the monitor (user code E11 or E15 in the SINOCMP table).

Common-rail fuel runs at very high pressure. Never open a high-pressure line or fitting with the engine running or just after it stops - a fine fuel jet can pierce skin.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.