John Deere · Engine control unit (ECU) - PowerTech engine
John Deere Fault Code ECU 000097.04
Water in fuel separator full
What does John Deere code ECU 000097.04 mean?
The ECU reports the water in fuel separator is full, meaning water has collected in the fuel system. The operator may see a warning and ignoring it can damage injectors and the high pressure pump. Urgency: check soon - the machine may derate or limit a function. Check first: drain the water separator bowl and watch what comes out; a lot of water means the tank is contaminated.
- ECU
- Which controller reports it
- 000097
- Water in fuel indicator
- .04
- Voltage below normal or shorted low
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Drain the water separator bowl and watch what comes out; a lot of water means the tank is contaminated
Then 4 more checksWhere this code shows
Turn the key on and open the monitor's diagnostic/fault screen.
Checks
0 of 5 done
Causes
- Water collected in the fuel system from condensation or contaminated fuel
- Separator bowl not drained at the service interval
- Water getting in through a loose tank cap or a damaged tank vent
- Poor fuel quality from the supplier
How it failed
You'll notice: The ECU reports that the water in fuel separator is full.
Lost messageRead from how the source describes the code
A module stopped hearing another on the data link, or the data came late or garbled.
- Meter test
- Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
- Good result
- About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
When to stop
Common-rail fuel runs at very high pressure. Never open a high-pressure line or fitting with the engine running or just after it stops - a fine fuel jet can pierce skin.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Engine, overheat, fuel and water alarms on the monitor
7 other codes on this part are also lost message (DSZ 20101.02, ICZ 20101.02, DSZ 20102.02, ICZ 20102.02 and more). When they show together, start at the wiring and connector they share.
- ECU 000097.03Water in fuel sensor voltage highShorted highCheck soon
- ECU 000097.04Water in fuel separator fullLost messageCheck soon
- ECU 001110.31Engine protection shutdownOtherStop now
- DSZ 13310.03Shorted circuit in coolant temperature sensorShort circuitCheck soon
- ICZ 13310.03Shorted circuit in coolant temperature sensorShort circuitCheck soon
- ICZ 13334.02Radiator coolant errorOtherCheck soon
- DSZ 20100.02Overheat alarmReal conditionCheck soon
- DSZ 20101.02Engine warning alarmLost messageCheck soon
- ICZ 20101.02Engine warning alarmLost messageCheck soon
Show the other 15 codesHide the other codes
- DSZ 20102.02Engine oil pressure alarmLost messageStop now
- ICZ 20102.02Engine oil pressure alarmLost messageStop now
- DSZ 20107.02Water separator alarmLost messageCheck soon
- DSZ 20110.02Fuel filter restriction alarmReal conditionCheck soon
- ICZ 20110.02Fuel filter restriction alarmReal conditionCheck soon
- DSZ 20114.02Overheat alarmReal conditionCheck soon
- ICZ 20114.02Overheat alarmReal conditionCheck soon
- DSZ 20142.02Intake air temperature alarmReal conditionCheck soon
- ICZ 20142.02Intake air temperature alarmReal conditionCheck soon
- DSZ 20145.02Boost temperature increase alarmOtherCheck soon
- ICZ 20145.02Boost temperature increase alarmOtherCheck soon
- DSZ 20146.02Fuel temperature increase alarmLost messageCheck soon
- ICZ 20146.02Fuel temperature increase alarmLost messageCheck soon
- DSZ 20149.02EGR gas temperature alarmReal conditionCheck soon
- ICZ 20149.02EGR gas temperature alarmReal conditionCheck soon
Other John Deere codes: Engine control unit (ECU) - PowerTech engine
- ECU 000100.01Low engine oil pressure
- ECU 000100.03Engine oil pressure input voltage high
- ECU 000100.04Engine oil pressure signal voltage low
- ECU 000100.18Engine power limited by oil pressure
- ECU 000100.31Oil pressure sensed with engine stopped
- ECU 000102.02Manifold air pressure sensor trouble
- ECU 000102.03Manifold air pressure sensor fault
- ECU 000102.04Manifold air pressure signal voltage low
Related on Equipments Finder
Source
Inside the Yard - John Deere fault codes list (ECU engine codes)
This source lists ECU 000097.04 and its meaning. The guidance on this page is general, not taken from it.
The source covers: John Deere PowerTech engines; code list comes from tractor-based sources, confirm for your machine.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
