J1939 · Aftertreatment - SCR/DEF
SPN 3216 Fault Code
Aftertreatment 1 intake NOx
What does SPN 3216 mean?
Nitrogen oxide level in the exhaust entering the SCR, measured by the upstream NOx sensor. The ECM uses it to set the DEF dose and to check engine-out emissions. How urgent it is depends on the FMI after SPN 3216 - pick it below. Check first: check the upstream sensor connector and wiring for corrosion, bent pins and chafing.
- SPN 3216
- Aftertreatment 1 intake NOx
- FMI ?
- How it failed - the number after the SPN
Can I keep running with it?
Depends on the FMI
How urgent it is depends on the FMI after SPN 3216 - pick it below.
What should I check first?
Check the upstream sensor connector and wiring for corrosion, bent pins and chafing
Then 4 more checksWhere to read it
Connect a J1939-capable scan tool to the 9-pin diagnostic port.
Which FMI shows after SPN 3216?
You'll notice: The NOx sensor ahead of the SCR is faulty or unreliable, so the ECM cannot read engine-out NOx for the DEF dose or its checks.
Find the number shown after SPN 3216 on your display. 5 of them have their own page with causes and checks.
- 2SPN 3216 FMI 2: Data is erratic, intermittent or incorrectErratic or implausibleCummins ISX15, Mack MP8, Mack MP7, Volvo D13
- 3SPN 3216 FMI 3: Signal voltage is above normal, or the circuit is shorted to a high sourceShorted highDetroit DD15, Detroit DD13, Mack MP8, Mack MP7 and 2 more
- 4SPN 3216 FMI 4: Signal voltage is below normal, or the circuit is shorted to a low sourceShorted lowCummins ISX15, Detroit DD15, Detroit DD13
- 5SPN 3216 FMI 5: Current is below normal, or the circuit is openOpen circuitMack MP8, Mack MP7, Volvo D13
- 8SPN 3216 FMI 8: NOx sensor operation is not stableErratic or implausibleDetroit DD13 Gen 5, Detroit DD15 Gen 5
- 9SPN 3216 FMI 9: Abnormal update rate: the signal or message is late or missingLost messageCummins ISX15, Mack MP8, Mack MP7, Volvo D13
- 10SPN 3216 FMI 10: The value is changing at an abnormal rateErratic or implausibleCummins ISX15
- 11SPN 3216 FMI 11: A fault exists but the ECM cannot identify its causeOtherMack MP8, Mack MP7, Volvo D13
- 12SPN 3216 FMI 12: Bad intelligent device or componentPart or controllerMack MP8, Mack MP7, Volvo D13
- 13SPN 3216 FMI 13: The value is out of calibrationPart or controllerCummins ISX15, Mack MP8, Mack MP7, Volvo D13
- 14SPN 3216 FMI 14: A special-instruction condition defined by the engine maker appliesOtherMack MP8, Mack MP7, Volvo D13
- 15SPN 3216 FMI 15: NOx sensor data is erratic or its response is wrongReal conditionPACCAR MX-13
- 16SPN 3216 FMI 16: Value is above the normal range, moderately severe levelReal conditionCummins ISX15
- 18SPN 3216 FMI 18: Inlet NOx sensor has drifted lowReal conditionDetroit DD15, Detroit DD13
- 20SPN 3216 FMI 20: Inlet NOx sensor has drifted highErratic or implausibleCummins ISX15, Detroit DD13 Gen 5, Detroit DD15 Gen 5, PACCAR MX-13
- 21SPN 3216 FMI 21: Inlet NOx sensor has drifted lowErratic or implausibleDetroit DD15, Detroit DD13, Detroit DD13 Gen 5, Detroit DD15 Gen 5 and 1 more
Checks
0 of 5 done
When to stop
Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.
How urgent SPN 3216 is depends on its FMI and whether the engine has derated. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Causes
- Circuit fault: wiring or connector problem at the upstream sensor plug from heat, vibration or corrosion
- Upstream NOx sensor failed, aged or soot-coated, so it reads wrongly or stops responding
- Exhaust leak near the sensor skewing the reading
- NOx sensor module on the lead lost power or ground, or its CAN link is faulty
Other Aftertreatment - SCR/DEF codes
Source
Cummins ISX15 2013-2018 fault codes list (Diesel Laptops)
This list names SPN 3216 and the FMIs above for the engines it covers. The guidance on this page is general, not taken from it.
The source covers: Cummins ISX15 (2013-2018) and X15; same SPN on other J1939 engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
