EF Logo

Cummins · Aftertreatment

Cummins DEF dosing unit, valves and heater fault codes

The DEF dosing unit holds the DEF pump, a pressure sensor and the dosing valve that injects fluid into the exhaust. A return valve lets DEF flow back to the tank so the unit can purge and prime, and a heater with its own relay and temperature feedback stops the unit freezing.

More about these parts

The ECM drives each of these and monitors the circuits and the resulting dosing quantity.

FaultCheck1682Cummins · DEF dosing unit input lines
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Connect INSITE or another J1939-capable scan tool to the 9-pin diagnostic port.

What do these codes mean?

Cummins codes 1681 to 6486 are all about the dEF dosing unit, valves and heater. The most common failure type is shorted high (6 of 30); none needs an immediate stop. Start with this check: check the dosing unit connector and harness for corrosion, melted pins and chafing.

How urgent are they?

None of the 30 codes here means stop now; 29 can wait until the shift ends, but find the cause before the next one; 1 is information only.

  • Check soon29
  • Info1

What should I check first?

Check the dosing unit connector and harness for corrosion, melted pins and chafing

Shared checks

30 of 30

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • DEF dosing unit6 codes

    • Cummins 1681DEF dosing unit: Bad device or component

      The ECM judges the DEF dosing unit to be an internal failure of the device or module.· Part or controller
      Check soon

      Causes

      • Internal failure of the device
      • Supply or ground problem causing it to reset
      • Corrupt software

      Checks

      1. 1Check supply and ground at the device before condemning it
      2. 2Reflash with the correct software where possible
      3. 3Replace the device if the fault persists after the supply tests are good
      ControllerPartSupplySignalGround?
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Check power and ground at the module connector with the key on, then its fuses.

      Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

    • Cummins 3558DEF dosing unit: Circuit voltage high

      The ECM sees the DEF dosing unit circuit voltage too high, which indicates a short to supply or an open ground in the dosing unit circuit.· Shorted high
      Check soon

      Causes

      • Dosing unit harness shorted to supply
      • Open ground in the dosing unit
      • Dosing unit control board failed

      Checks

      1. 1Inspect the dosing unit connector for crystals and corrosion
      2. 2Check the ground and supply at the connector with the key on
      3. 3Look for harness damage near the exhaust where the dosing unit wiring runs
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

      Good: Open circuit (OL) between them. Any low reading is the short.

    • Cummins 3559DEF dosing unit: Voltage low / shorted low

      The ECM sees the DEF dosing unit signal circuit below its normal voltage range, which points to a short to ground or a failed input rather than a real condition.· Shorted low
      Check soon

      Causes

      • Signal wire shorted to ground
      • Failed input or damaged connector at the module

      Checks

      1. 1Check the wiring and connector for shorts to ground
      2. 2Compare the reading with the related signal in INSITE
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

      Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

      Source wording:DEF dosing unit - voltage low (shorted to a low source)

    • Cummins 3561DEF dosing unit: Current low / open circuit

      The ECM commands the DEF dosing unit but sees little or no current flow.· Open circuit
      Check soon

      Causes

      • Open wire or a terminal pushed back in the connector
      • Open winding in the component
      • Blown fuse or failed relay feeding the circuit

      Checks

      1. 1Check continuity from the ECM pin to the DEF dosing unit connector, wiggling the harness as you test
      2. 2Measure the component resistance with the connector unplugged; an open reading means the part has failed
      3. 3Check the fuse and relay feeding the circuit
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

      Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

      Source wording:DEF dosing unit - current low or open circuit

    • Cummins 3612DEF dosing unit: Mechanical fault or not responding

      The ECM commands the DEF dosing unit but it does not respond as expected, or its movement is out of adjustment.· Part or controller
      Check soon

      Causes

      • Mechanism seized, sooted or blocked
      • Wear or incorrect adjustment of the linkage or part
      • Supply or return fault limiting its movement

      Checks

      1. 1Command the DEF dosing unit in INSITE and watch whether it moves and returns
      2. 2Inspect the part and its linkage for sticking, debris or wear
      3. 3Check supply and return connections before replacing it
      ControllerPartSupplySignalGround?
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Check power and ground at the module connector with the key on, then its fuses.

      Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

    • Cummins 3679DEF dosing unit: Root cause not known

      The ECM detects a problem with the DEF dosing unit but cannot tie it to one specific cause.· Other
      Info

      Causes

      • A related fault that set first
      • An intermittent connection or supply problem

      Checks

      1. 1Read all active and inactive codes and work the others first
      2. 2Check the supply, ground and connectors of the circuit involved
      3. 3Read the freeze-frame data for the conditions when it set
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Read the code with the service tool and note which other codes are active with it.

      Good: Codes that appear together usually share one cause - start with the wiring they share.

  • DEF dosing unit input lines2 codes

    • Cummins 1682DEF dosing unit input lines: Condition exists

      The ECM sees a problem with the DEF supply or return lines going to the dosing unit, such as a leak, a blockage or a swapped line.· Other
      Check soon

      Causes

      • DEF supply or return line kinked, plugged or swapped at the dosing unit
      • DEF line leaking or frozen
      • DEF pump or filter plugged with crystals
      • Wrong line connector fitted after service work

      Checks

      1. 1Look over all DEF lines for leaks, crystals and kinks from the tank to the dosing unit
      2. 2Check the supply and return lines are on the correct ports
      3. 3In cold weather check that the DEF line heaters warm the lines, because frozen DEF blocks the dosing unit inlet
      4. 4Run the DEF dosing system test in INSITE and watch pressure
      5. 5Replace the DEF filter and clean the pump pickup if the pressure builds slowly
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Read the code with the service tool and note which other codes are active with it.

      Good: Codes that appear together usually share one cause - start with the wiring they share.

    • Cummins 3569DEF dosing unit input lines: Mechanical fault or not responding

      The ECM commands the DEF dosing unit input lines but it does not respond as expected, or its movement is out of adjustment.· Part or controller
      Check soon

      Causes

      • Mechanism seized, sooted or blocked
      • Wear or incorrect adjustment of the linkage or part
      • Supply or return fault limiting its movement

      Checks

      1. 1Command the DEF dosing unit input lines in INSITE and watch whether it moves and returns
      2. 2Inspect the part and its linkage for sticking, debris or wear
      3. 3Check supply and return connections before replacing it
      ControllerPartSupplySignalGround?
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Check power and ground at the module connector with the key on, then its fuses.

      Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

  • DEF dosing unit temperature1 code

    • Cummins 2976DEF dosing unit temperature: Erratic reading

      The ECM judges the DEF dosing unit temperature to be erratic, intermittent or implausible.· Erratic or implausible
      Check soon

      Causes

      • Intermittent connector or wiring contact
      • Sensor ageing or failing
      • A real fluctuation in the system it measures

      Checks

      1. 1Watch the DEF dosing unit temperature live and wiggle the harness and connector to catch dropouts
      2. 2Compare it with a related sensor to see which one is wrong
      3. 3Check the connector for moisture and corrosion
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Watch the live value on the service tool while you flex the harness and tap the connector.

      Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

      Source wording:DEF dosing unit temperature - data erratic or incorrect

  • DEF dosing valve circuit1 code

    • Cummins 3565DEF dosing valve circuit: Voltage high

      The ECM sees the DEF dosing valve output high, which indicates a short to supply or an open return in the dosing valve circuit.· Shorted high
      Check soon

      Causes

      • Dosing valve driver wire shorted to supply
      • Open return at the valve
      • Valve stuck energised

      Checks

      1. 1Command the valve in the DEF test and listen for ticking
      2. 2Measure the driver pin at the unplugged connector with the key on
      3. 3Check the return wire for continuity from the connector back to the ECM pin
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

      Good: Open circuit (OL) between them. Any low reading is the short.

  • DEF dosing valve3 codes

    • Cummins 3566DEF dosing valve: Voltage low / shorted low

      The ECM sees the DEF dosing valve drive circuit with voltage below the expected level.· Shorted low
      Check soon

      Causes

      • Output wire shorted to ground or chafed through to the chassis
      • Component winding shorted internally
      • Connector corroded and bridging the pins

      Checks

      1. 1Unplug the DEF dosing valve connector and measure the output pin to ground; a short here means the harness is at fault
      2. 2Measure the component resistance across its pins; a very low reading means a shorted winding
      3. 3Inspect the connector for moisture and bridged terminals
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

      Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

      Source wording:DEF dosing valve - voltage low (shorted to a low source)

    • Cummins 3568DEF dosing valve: Mechanical failure

      The ECM has commanded the DEF dosing valve but the pressure or flow does not follow.· Real condition
      Check soon

      Causes

      • Dosing nozzle blocked by crystals
      • Dosing valve stuck open or closed
      • DEF filter plugged

      Checks

      1. 1Remove the dosing valve and inspect the nozzle for crystals
      2. 2Replace the DEF filter and check the pump pressure
      3. 3Run the DEF dosing test and watch the pressure
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Check the real value with a separate gauge or thermometer before blaming the sensor.

      Good: If the gauge agrees with the display, fix the machine, not the sensor.

    • Cummins 3755DEF dosing valve: Erratic reading

      The ECM judges the DEF dosing valve to be erratic, intermittent or implausible.· Erratic or implausible
      Check soon

      Causes

      • Intermittent connector or wiring contact
      • Sensor ageing or failing
      • A real fluctuation in the system it measures

      Checks

      1. 1Watch the DEF dosing valve live and wiggle the harness and connector to catch dropouts
      2. 2Compare it with a related sensor to see which one is wrong
      3. 3Check the connector for moisture and corrosion
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Watch the live value on the service tool while you flex the harness and tap the connector.

      Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

      Source wording:DEF dosing valve - data erratic or incorrect

  • DEF return valve3 codes

    • Cummins 3577DEF return valve: Voltage high / shorted high

      The ECM sees the DEF return valve drive circuit with voltage above the expected level.· Shorted high
      Check soon

      Causes

      • Output wire shorted to battery or a switched power feed
      • Open ground or return path on the component
      • Component winding failed or its connector damaged

      Checks

      1. 1Unplug the DEF return valve connector, key on, and measure the output pin to ground; battery voltage with nothing connected points to a short to power
      2. 2Inspect the harness for a rubbed wire or damaged splice touching a power feed
      3. 3Measure the component resistance across its pins to rule out an open winding
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

      Good: Open circuit (OL) between them. Any low reading is the short.

      Source wording:DEF return valve - voltage high (shorted to a high source)

    • Cummins 3579DEF return valve: Current low / open circuit

      The ECM commands the DEF return valve but sees little or no current flow.· Open circuit
      Check soon

      Causes

      • Open wire or a terminal pushed back in the connector
      • Open winding in the component
      • Blown fuse or failed relay feeding the circuit

      Checks

      1. 1Check continuity from the ECM pin to the DEF return valve connector, wiggling the harness as you test
      2. 2Measure the component resistance with the connector unplugged; an open reading means the part has failed
      3. 3Check the fuse and relay feeding the circuit
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

      Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

      Source wording:DEF return valve - current low or open circuit

    • Cummins 4157DEF return valve: Mechanical fault or not responding

      The ECM commands the DEF return valve but it does not respond as expected, or its movement is out of adjustment.· Part or controller
      Check soon

      Causes

      • Mechanism seized, sooted or blocked
      • Wear or incorrect adjustment of the linkage or part
      • Supply or return fault limiting its movement

      Checks

      1. 1Command the DEF return valve in INSITE and watch whether it moves and returns
      2. 2Inspect the part and its linkage for sticking, debris or wear
      3. 3Check supply and return connections before replacing it
      ControllerPartSupplySignalGround?
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Check power and ground at the module connector with the key on, then its fuses.

      Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

  • DEF dosing unit heater relay2 codes

    • Cummins 4155DEF dosing unit heater relay: Voltage high / shorted high

      The ECM sees the DEF dosing unit heater relay drive circuit with voltage above the expected level.· Shorted high
      Check soon

      Causes

      • Output wire shorted to battery or a switched power feed
      • Open ground or return path on the component
      • Component winding failed or its connector damaged

      Checks

      1. 1Unplug the DEF dosing unit heater relay connector, key on, and measure the output pin to ground; battery voltage with nothing connected points to a short to power
      2. 2Inspect the harness for a rubbed wire or damaged splice touching a power feed
      3. 3Measure the component resistance across its pins to rule out an open winding
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

      Good: Open circuit (OL) between them. Any low reading is the short.

      Source wording:DEF dosing unit heater relay - voltage high (shorted to a high source)

    • Cummins 4156DEF dosing unit heater relay: Voltage low / shorted low

      The ECM sees the DEF dosing unit heater relay drive circuit with voltage below the expected level.· Shorted low
      Check soon

      Causes

      • Output wire shorted to ground or chafed through to the chassis
      • Component winding shorted internally
      • Connector corroded and bridging the pins

      Checks

      1. 1Unplug the DEF dosing unit heater relay connector and measure the output pin to ground; a short here means the harness is at fault
      2. 2Measure the component resistance across its pins; a very low reading means a shorted winding
      3. 3Inspect the connector for moisture and bridged terminals
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

      Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

      Source wording:DEF dosing unit heater relay - voltage low (shorted to a low source)

  • DEF dosing unit heater4 codes

    • Cummins 4167DEF dosing unit heater: Erratic reading

      The ECM judges the DEF dosing unit heater to be erratic, intermittent or implausible.· Erratic or implausible
      Check soon

      Causes

      • Intermittent connector or wiring contact
      • Sensor ageing or failing
      • A real fluctuation in the system it measures

      Checks

      1. 1Watch the DEF dosing unit heater live and wiggle the harness and connector to catch dropouts
      2. 2Compare it with a related sensor to see which one is wrong
      3. 3Check the connector for moisture and corrosion
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Watch the live value on the service tool while you flex the harness and tap the connector.

      Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

      Source wording:DEF dosing unit heater - data erratic or incorrect

    • Cummins 4168DEF dosing unit heater: Voltage high / shorted high

      The ECM sees the DEF dosing unit heater drive circuit with voltage above the expected level.· Shorted high
      Check soon

      Causes

      • Output wire shorted to battery or a switched power feed
      • Open ground or return path on the component
      • Component winding failed or its connector damaged

      Checks

      1. 1Unplug the DEF dosing unit heater connector, key on, and measure the output pin to ground; battery voltage with nothing connected points to a short to power
      2. 2Inspect the harness for a rubbed wire or damaged splice touching a power feed
      3. 3Measure the component resistance across its pins to rule out an open winding
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

      Good: Open circuit (OL) between them. Any low reading is the short.

      Source wording:DEF dosing unit heater - voltage high (shorted to a high source)

    • Cummins 4169DEF dosing unit heater: Voltage low / shorted low

      The ECM sees the DEF dosing unit heater drive circuit with voltage below the expected level.· Shorted low
      Check soon

      Causes

      • Output wire shorted to ground or chafed through to the chassis
      • Component winding shorted internally
      • Connector corroded and bridging the pins

      Checks

      1. 1Unplug the DEF dosing unit heater connector and measure the output pin to ground; a short here means the harness is at fault
      2. 2Measure the component resistance across its pins; a very low reading means a shorted winding
      3. 3Inspect the connector for moisture and bridged terminals
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

      Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

      Source wording:DEF dosing unit heater - voltage low (shorted to a low source)

    • Cummins 4171DEF dosing unit heater: Below normal· moderately severe

      The DEF dosing unit heater is below its normal operating range and the ECM rates it as moderately severe.· Real condition
      Check soon

      Causes

      • The monitored condition really is too low because of the system it measures
      • A related fault that set first and is pushing the reading out of range

      Checks

      1. 1Compare the live DEF dosing unit heater with a second reading or gauge to see whether the condition is real
      2. 2Read the freeze-frame for speed, load and temperature when the code set
      3. 3Clear any other active codes first and retest under load
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Check the real value with a separate gauge or thermometer before blaming the sensor.

      Good: If the gauge agrees with the display, fix the machine, not the sensor.

      Source wording:DEF dosing unit heater - below normal - moderately severe

  • DEF dosing unit heater temperature2 codes

    • Cummins 4245DEF dosing unit heater temperature: Erratic reading

      The ECM judges the DEF dosing unit heater temperature to be erratic, intermittent or implausible.· Erratic or implausible
      Check soon

      Causes

      • Intermittent connector or wiring contact
      • Sensor ageing or failing
      • A real fluctuation in the system it measures

      Checks

      1. 1Watch the DEF dosing unit heater temperature live and wiggle the harness and connector to catch dropouts
      2. 2Compare it with a related sensor to see which one is wrong
      3. 3Check the connector for moisture and corrosion
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Watch the live value on the service tool while you flex the harness and tap the connector.

      Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

      Source wording:DEF dosing unit heater temperature - data erratic or incorrect

    • Cummins 4251DEF dosing unit heater temperature: Abnormal rate of change

      The DEF dosing unit heater temperature reading is changing faster than the real quantity could move.· Erratic or implausible
      Check soon

      Causes

      • Loose or corroded connector causing intermittent contact
      • Intermittent wiring fault that opens and closes
      • Sensor starting to fail

      Checks

      1. 1Watch the DEF dosing unit heater temperature reading live and wiggle the harness and connector to see whether it jumps
      2. 2Inspect the connector pins for corrosion and spread terminals
      3. 3Compare with a related sensor to see whether the jump is real
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Watch the live value on the service tool while you flex the harness and tap the connector.

      Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • SCR actual dosing reagent quantity1 code

    • Cummins 4658SCR actual dosing reagent quantity: Below normal· moderately severe

      The SCR actual dosing reagent quantity is below its normal operating range and the ECM rates it as moderately severe.· Real condition
      Check soon

      Causes

      • The monitored condition really is too low because of the system it measures
      • A related fault that set first and is pushing the reading out of range

      Checks

      1. 1Compare the live SCR actual dosing reagent quantity with a second reading or gauge to see whether the condition is real
      2. 2Read the freeze-frame for speed, load and temperature when the code set
      3. 3Clear any other active codes first and retest under load
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Check the real value with a separate gauge or thermometer before blaming the sensor.

      Good: If the gauge agrees with the display, fix the machine, not the sensor.

      Source wording:SCR actual dosing reagent quantity - below normal - moderately severe

  • DEF dosing unit relay feedback2 codes

    • Cummins 5866DEF dosing unit relay feedback: Voltage high / shorted high

      The ECM sees the DEF dosing unit relay feedback drive circuit with voltage above the expected level.· Shorted high
      Check soon

      Causes

      • Output wire shorted to battery or a switched power feed
      • Open ground or return path on the component
      • Component winding failed or its connector damaged

      Checks

      1. 1Unplug the DEF dosing unit relay feedback connector, key on, and measure the output pin to ground; battery voltage with nothing connected points to a short to power
      2. 2Inspect the harness for a rubbed wire or damaged splice touching a power feed
      3. 3Measure the component resistance across its pins to rule out an open winding
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

      Good: Open circuit (OL) between them. Any low reading is the short.

      Source wording:DEF dosing unit relay feedback - voltage high (shorted to a high source)

    • Cummins 5867DEF dosing unit relay feedback: Voltage low / shorted low

      The ECM sees the DEF dosing unit relay feedback drive circuit with voltage below the expected level.· Shorted low
      Check soon

      Causes

      • Output wire shorted to ground or chafed through to the chassis
      • Component winding shorted internally
      • Connector corroded and bridging the pins

      Checks

      1. 1Unplug the DEF dosing unit relay feedback connector and measure the output pin to ground; a short here means the harness is at fault
      2. 2Measure the component resistance across its pins; a very low reading means a shorted winding
      3. 3Inspect the connector for moisture and bridged terminals
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

      Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

      Source wording:DEF dosing unit relay feedback - voltage low (shorted to a low source)

  • DEF actual dosing quantity1 code

    • Cummins 6486DEF actual dosing quantity: Above normal· moderately severe

      The DEF actual dosing quantity is above its normal operating range and the ECM rates it as moderately severe.· Real condition
      Check soon

      Causes

      • The monitored condition really is too high because of the system it measures
      • A related fault that set first and is pushing the reading out of range

      Checks

      1. 1Compare the live DEF actual dosing quantity with a second reading or gauge to see whether the condition is real
      2. 2Read the freeze-frame for speed, load and temperature when the code set
      3. 3Clear any other active codes first and retest under load
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Check the real value with a separate gauge or thermometer before blaming the sensor.

      Good: If the gauge agrees with the display, fix the machine, not the sensor.

      Source wording:DEF actual dosing quantity - above normal - moderately severe

  • Other codes2 codes

    • Cummins 3567DEF dosing valve circuit open circuit

      The ECM finds no current flowing in the DEF dosing valve circuit when it commands it on, so the circuit is open or the load is unplugged.· Open circuit
      Check soon

      Causes

      • Dosing valve coil open
      • Connector corroded
      • Wire broken near the dosing unit

      Checks

      1. 1Command the dosing valve and listen for it ticking
      2. 2Measure the DEF dosing valve coil resistance at the connector and compare it with the service value
      3. 3Test both dosing valve wires for continuity back to the control unit with the key off
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

      Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

    • Cummins 3578DEF return valve circuit shorted low or driver voltage low

      The ECM drives the DEF return valve circuit but sees its output pulled to ground.· Shorted low
      Check soon

      Causes

      • Return valve wire shorted to ground
      • Valve coil shorted
      • Connector wet

      Checks

      1. 1Command the DEF return valve in the INSITE DEF test and listen for it to click
      2. 2Measure the DEF return valve coil resistance at the connector against the service value
      3. 3Ohm the return valve driver wire to ground with the ECM plug removed to find a short
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

      Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

Shared checks

Checks, in order

  1. 1Check the dosing unit connector and harness for corrosion, melted pins and chafing
  2. 2Unplug the suspect component and check its circuit for opens and shorts to ground and to power
  3. 3Check the DEF quality and the line and filter condition for crystals or restriction
  4. 4Test the heater and relay operation in cold conditions
  5. 5Read the dosing unit status and pressure live during a prime or purge cycle
  6. 6Compare the commanded and actual dosing quantity to see whether the fault is electrical or mechanical

Causes

  • Connector or harness damage at the dosing unit
  • Failed pump, dosing valve, return valve or heater
  • Blocked or crystallised DEF in the nozzle or lines
  • Frozen unit or a failed heater or relay

Most common here: shorted high (6 of 30)

Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

When to stop

You'll notice: A DEF or SCR warning, poor NOx control, possible derate, and in cold weather a unit that never thaws.

Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.