Cat · Engine sensors
Cat Fault Code CID 262 FMI 03
5 V sensor supply voltage high
What does Cat code CID 262 FMI 03 mean?
The ECM's 5 V supply for the pressure and temperature sensors read above 5.16 V for more than one second. The manual lists a harness shorted to another power source or the ECM. Urgency: check soon - the machine may derate or limit a function. Check first: connect Cat ET and confirm 262-3 is active before looking at other sensor codes.
- CID 262
- Which component is at fault
- FMI 03
- Voltage above normal or shorted high
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Connect Cat ET and confirm 262-3 is active before looking at other sensor codes.
Then 4 more checksWhere this code shows
Turn the key on and check the cluster or monitor for a warning lamp.
Checks
0 of 5 done
Causes
- Engine control harness shorted to another power source
- Engine ECM 5 V supply fault
- A shorted sensor pulling its supply pin up
How it failed
You'll notice: Several sensors can show wrong values at once, so you may see oil, coolant, boost and rail pressure codes together.
Shorted highRead from FMI 3: voltage above normal or shorted high
The signal sits at or near the supply voltage - more than a working sensor can send.
- Meter test
- Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
- Good result
- Open circuit (OL) between them. Any low reading is the short.
When to stop
Let the engine cool before opening the cooling system; a hot cap releases scalding coolant. Running on with an overheat warning risks a head gasket or seized engine.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Engine sensors and sensor supply
6 other codes on this part are also shorted high (CID 41 FMI 03, CID 91 FMI 03, CID 100 FMI 03, CID 110 FMI 03 and more). When they show together, start at the wiring and connector they share.
- CID 110 FMI 03Engine coolant temperature sensor voltage highShorted highCheck soon
- CID 110 FMI 04Engine coolant temperature sensor voltage lowShorted lowCheck soon
- CID 172 FMI 03Intake manifold air temperature sensor voltage highShorted highCheck soon
- CID 172 FMI 04Intake manifold air temperature sensor voltage lowShorted lowCheck soon
- CID 262 FMI 035 V sensor supply voltage highShorted highCheck soon
- E360Low engine oil pressureOtherStop now
- E361High engine coolant temperatureOtherStop now
- E539High intake manifold temperatureReal conditionCheck soon
- E1044High intake manifold pressureOtherCheck soon
Show the other 8 codesHide the other codes
- CID 41 FMI 038 V sensor supply voltage highShorted highCheck soon
- CID 91 FMI 03Throttle position sensor voltage highShorted highCheck soon
- CID 91 FMI 04Throttle position sensor voltage lowShorted lowCheck soon
- CID 100 FMI 03Engine oil pressure sensor voltage highShorted highCheck soon
- CID 100 FMI 04Engine oil pressure sensor voltage lowShorted lowCheck soon
- E1045Low intake manifold pressureOtherCheck soon
- CID 1785 FMI 03Intake manifold pressure sensor voltage highShorted highCheck soon
- CID 1785 FMI 04Intake manifold pressure sensor voltage lowShorted lowCheck soon
Other Cat codes: Engine sensors
Related on Equipments Finder
Source
This source lists CID 262 FMI 03 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Cat 924H wheel loader with C6.6 engine (engine ECM), per the 924H field maintenance manual; the same CID-FMI scheme is used on other Cat machines with C-series ECMs.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
