Volvo/Mack · MID 128 engine ECU - aftertreatment (DPF, DEF, NOx)
Volvo/Mack Fault Code MID 128 PSID 90 FMI 1
DEF dosing too low - NOx limits exceeded, poor DEF quality
What does Volvo/Mack code MID 128 PSID 90 FMI 1 mean?
The SCR system sees too little DEF being dosed, or the DEF quality is too poor to reduce NOx. Mack lists the DEF quality, a clogged DEF line, the doser or the aftertreatment control module. Urgency: stop now - shut down and fix before working on. Check first: test the DEF with a refractometer; it must read the correct concentration, not water.
- MID 128
- Which control unit reports it
- PSID 90
- Maker component at fault
- FMI 1
- Data below normal, most severe
Can I keep running with it?
Stop now
Shut down and fix before working on. Running on risks damage or the machine locks out.
What should I check first?
Test the DEF with a refractometer; it must read the correct concentration, not water
Then 4 more checksWhere to read it
Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.
Checks
0 of 5 done
Causes
- Poor quality or diluted DEF in the tank
- DEF line clogged or crystallised
- DEF doser blocked
- Aftertreatment control module failure
How it failed
You'll notice: A yellow lamp lights and the engine derates.
Real conditionRead from FMI 1: data below normal, most severe
The sensor reading is valid but outside the allowed range - the problem may be real.
- Meter test
- Check the real value with a separate gauge or thermometer before blaming the sensor.
- Good result
- If the gauge agrees with the display, fix the machine, not the sensor.
When to stop
Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: DEF dosing performance
- MID 128 PSID 90 FMI 1DEF dosing too low - NOx limits exceeded, poor DEF qualityReal conditionStop now
- MID 128 PSID 90 FMI 7DEF dosing interrupted - NOx limits exceededPart or controllerCheck soon
Other Volvo/Mack codes: MID 128 engine ECU - aftertreatment (DPF, DEF, NOx)
- MID 128 PSID 46 FMI 0SCR system severe fault - operator inducement
- MID 128 PSID 47 FMI 0Unable to reach regeneration temperature
- MID 128 PSID 47 FMI 1Aftertreatment temperature too high during regeneration
- MID 128 PID 81 FMI 0DPF differential pressure critically high
- MID 128 PID 81 FMI 3DPF differential pressure sensor signal high
- MID 128 PID 81 FMI 5DPF differential pressure sensor circuit open
- MID 128 PSID 121 FMI 7DEF pressure build-up failure - loss of prime
Related on Equipments Finder
Source
This source lists MID 128 PSID 90 FMI 1 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Mack MP7/MP8/MP10 engines (CHU, CXU, GU, TD) with the 2010-and-later MID 128 engine ECU; the same MID 128 numbers appear on Volvo D11/D13 engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
