Volvo/Mack · MID 128 engine ECU - aftertreatment (DPF, DEF, NOx)
Volvo/Mack Fault Code MID 128 PSID 121 FMI 7
DEF pressure build-up failure - loss of prime
What does Volvo/Mack code MID 128 PSID 121 FMI 7 mean?
The DEF pump cannot build pressure, which Mack calls a loss of prime. The pump is not drawing DEF or the line is leaking. Urgency: check soon - the machine may derate or limit a function. Check first: check the DEF level in the tank and top up with fresh fluid that meets the ISO 22241 standard.
- MID 128
- Which control unit reports it
- PSID 121
- Maker component at fault
- FMI 7
- Mechanical system not responding
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Check the DEF level in the tank and top up with fresh fluid that meets the ISO 22241 standard
Then 4 more checksWhere to read it
Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.
Checks
0 of 5 done
Causes
- Empty DEF tank
- DEF filter clogged
- DEF inlet pipe leak
- DEF pump failed
How it failed
You'll notice: MIL and yellow lamp lit and no DEF dosing, so the truck will start derating if it is not fixed.
Part or controllerRead from FMI 7: mechanical system not responding
The controller reports a part, module or its software as faulty or not responding.
- Meter test
- Check power and ground at the module connector with the key on, then its fuses.
- Good result
- Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
When to stop
Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Other Volvo/Mack codes: MID 128 engine ECU - aftertreatment (DPF, DEF, NOx)
- MID 128 PSID 46 FMI 0SCR system severe fault - operator inducement
- MID 128 PSID 47 FMI 0Unable to reach regeneration temperature
- MID 128 PSID 47 FMI 1Aftertreatment temperature too high during regeneration
- MID 128 PID 81 FMI 0DPF differential pressure critically high
- MID 128 PID 81 FMI 3DPF differential pressure sensor signal high
- MID 128 PID 81 FMI 5DPF differential pressure sensor circuit open
- MID 128 PSID 90 FMI 1DEF dosing too low - NOx limits exceeded, poor DEF quality
- MID 128 PSID 90 FMI 7DEF dosing interrupted - NOx limits exceeded
Related on Equipments Finder
Source
This source lists MID 128 PSID 121 FMI 7 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Mack MP7/MP8/MP10 engines (CHU, CXU, GU, TD) with the 2010-and-later MID 128 engine ECU; the same MID 128 numbers appear on Volvo D11/D13 engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
