Volvo/Mack · MID 128 engine ECU - aftertreatment (DPF, DEF, NOx)
Volvo/Mack Fault Code MID 128 PPID 348 FMI 9
Inlet NOx sensor signal missing
What does Volvo/Mack code MID 128 PPID 348 FMI 9 mean?
The engine ECM lost communication with the inlet NOx sensor ahead of the SCR catalyst. The sensor control unit is not talking to the ECM. Urgency: check soon - the machine may derate or limit a function. Check first: check the inlet NOx sensor connector and its lock.
- MID 128
- Which control unit reports it
- PPID 348
- Maker parameter at fault
- FMI 9
- Abnormal update rate
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Check the inlet NOx sensor connector and its lock
Then 3 more checksWhere to read it
Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.
Checks
0 of 4 done
Causes
- Inlet NOx sensor unplugged or connector corroded
- NOx sensor control unit failed
- Wiring fault between the control unit and the engine ECM
How it failed
You'll notice: MIL and yellow lamp lit.
Lost messageRead from FMI 9: abnormal update rate
A module stopped hearing another on the data link, or the data came late or garbled.
- Meter test
- Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
- Good result
- About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
When to stop
Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: NOx sensors before and after the SCR
1 other code on this part is also lost message (MID 128 PPID 270 FMI 9). When they show together, start at the wiring and connector they share.
- MID 128 PPID 270 FMI 2Outlet NOx sensor reading not plausibleErratic or implausibleCheck soon
- MID 128 PPID 270 FMI 3Outlet NOx sensor signal shorted highShorted highCheck soon
- MID 128 PPID 270 FMI 5Outlet NOx sensor circuit openOpen circuitCheck soon
- MID 128 PPID 270 FMI 9Outlet NOx sensor signal missingLost messageCheck soon
- MID 128 PPID 348 FMI 2Inlet NOx sensor not plausibleErratic or implausibleCheck soon
- MID 128 PPID 348 FMI 9Inlet NOx sensor signal missingLost messageCheck soon
Other Volvo/Mack codes: MID 128 engine ECU - aftertreatment (DPF, DEF, NOx)
- MID 128 PSID 46 FMI 0SCR system severe fault - operator inducement
- MID 128 PSID 47 FMI 0Unable to reach regeneration temperature
- MID 128 PSID 47 FMI 1Aftertreatment temperature too high during regeneration
- MID 128 PID 81 FMI 0DPF differential pressure critically high
- MID 128 PID 81 FMI 3DPF differential pressure sensor signal high
- MID 128 PID 81 FMI 5DPF differential pressure sensor circuit open
Related on Equipments Finder
Source
This source lists MID 128 PPID 348 FMI 9 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Mack MP7/MP8/MP10 engines (CHU, CXU, GU, TD) with the 2010-and-later MID 128 engine ECU; the same MID 128 numbers appear on Volvo D11/D13 engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
