EF Logo

Volvo/Mack · MID 128 engine ECU - aftertreatment (DPF, DEF, NOx)

Volvo/Mack Fault Code MID 128 PPID 326 FMI 0

DPF soot level moderately high

What does Volvo/Mack code MID 128 PPID 326 FMI 0 mean?

The DPF system monitor reports a moderately high soot load. Mack lists a clogged DPF, a clogged hydrocarbon doser or regeneration being disabled. Urgency: check soon - the machine may derate or limit a function. Check first: check why regeneration did not run; look at the inhibit switch and regeneration history.

FaultCheckMID 128PPID 326FMI 0Volvo/Mack · MID 128 engine ECU - aftertreatment (DPF, DEF, NOx)
MID 128
Which control unit reports it
PPID 326
Maker parameter at fault
FMI 0
Data above normal, most severe

Can I keep running with it?

Check soon

The machine may derate or limit a function. Find the cause before the next shift.

What should I check first?

Check why regeneration did not run; look at the inhibit switch and regeneration history

Then 3 more checks
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.

Checks

0 of 4 done

Causes

  • Diesel particulate filter clogged
  • Hydrocarbon doser (fuel injector) clogged
  • Regeneration disabled by the driver or another component

How it failed

You'll notice: Yellow lamp lit and the engine derates at a medium to high level until the soot is burned off.

Real conditionRead from FMI 0: data above normal, most severe

The sensor reading is valid but outside the allowed range - the problem may be real.

allowed rangetime
The reading against the band the controller allows.
Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good result
If the gauge agrees with the display, fix the machine, not the sensor.

When to stop

Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.

Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Same part, other failures: DPF soot level

1 other code on this part is also real condition (MID 128 PPID 326 FMI 11). When they show together, start at the wiring and connector they share.

All 2 DPF soot level codes on one page

Source

Mack Group 28 Engine Control Module (ECM) Diagnostic Trouble Code Guide, 2010 Emissions CHU/CXU/GU/TD, PV776-89047073 (MID 128 PID/SID tables)

This source lists MID 128 PPID 326 FMI 0 and its meaning. The guidance on this page is general, not taken from it.

The source covers: Mack MP7/MP8/MP10 engines (CHU, CXU, GU, TD) with the 2010-and-later MID 128 engine ECU; the same MID 128 numbers appear on Volvo D11/D13 engines.

Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.