Volvo/Mack · MID 128 engine ECU - aftertreatment (DPF, DEF, NOx)
Volvo/Mack Fault Code MID 128 PPID 270 FMI 9
Outlet NOx sensor signal missing
What does Volvo/Mack code MID 128 PPID 270 FMI 9 mean?
The engine ECM lost communication with the outlet NOx sensor, which sits after the SCR catalyst. Mack lists the loss of the link between the NOx sensor's own control unit and the ECM. Urgency: check soon - the machine may derate or limit a function. Check first: check the outlet NOx sensor connector for water, melted pins and a loose lock.
- MID 128
- Which control unit reports it
- PPID 270
- Maker parameter at fault
- FMI 9
- Abnormal update rate
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Check the outlet NOx sensor connector for water, melted pins and a loose lock
Then 4 more checksWhere to read it
Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.
Checks
0 of 5 done
Causes
- Outlet NOx sensor unplugged, wiring broken or connector corroded
- NOx sensor control unit failed
- Low or unstable supply voltage to the NOx sensor
How it failed
You'll notice: MIL and yellow lamp lit.
Lost messageRead from FMI 9: abnormal update rate
A module stopped hearing another on the data link, or the data came late or garbled.
- Meter test
- Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
- Good result
- About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
When to stop
Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: NOx sensors before and after the SCR
1 other code on this part is also lost message (MID 128 PPID 348 FMI 9). When they show together, start at the wiring and connector they share.
- MID 128 PPID 270 FMI 2Outlet NOx sensor reading not plausibleErratic or implausibleCheck soon
- MID 128 PPID 270 FMI 3Outlet NOx sensor signal shorted highShorted highCheck soon
- MID 128 PPID 270 FMI 5Outlet NOx sensor circuit openOpen circuitCheck soon
- MID 128 PPID 270 FMI 9Outlet NOx sensor signal missingLost messageCheck soon
- MID 128 PPID 348 FMI 2Inlet NOx sensor not plausibleErratic or implausibleCheck soon
- MID 128 PPID 348 FMI 9Inlet NOx sensor signal missingLost messageCheck soon
Other Volvo/Mack codes: MID 128 engine ECU - aftertreatment (DPF, DEF, NOx)
- MID 128 PSID 46 FMI 0SCR system severe fault - operator inducement
- MID 128 PSID 47 FMI 0Unable to reach regeneration temperature
- MID 128 PSID 47 FMI 1Aftertreatment temperature too high during regeneration
- MID 128 PID 81 FMI 0DPF differential pressure critically high
- MID 128 PID 81 FMI 3DPF differential pressure sensor signal high
- MID 128 PID 81 FMI 5DPF differential pressure sensor circuit open
Related on Equipments Finder
Source
This source lists MID 128 PPID 270 FMI 9 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Mack MP7/MP8/MP10 engines (CHU, CXU, GU, TD) with the 2010-and-later MID 128 engine ECU; the same MID 128 numbers appear on Volvo D11/D13 engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
