Volvo/Mack · MID 128 engine ECU - sensors and levels
Volvo/Mack Fault Code MID 128 PID 111 FMI 1
Engine coolant level critically low
What does Volvo/Mack code MID 128 PID 111 FMI 1 mean?
The coolant level sensor says the coolant is critically below the allowed range. That is the engine telling you it is about to overheat, so it is treated as a real fault. Urgency: stop now - shut down and fix before working on. Check first: shut down and check the surge tank when cold; add coolant only after finding the loss.
- MID 128
- Which control unit reports it
- PID 111
- Parameter at fault
- FMI 1
- Data below normal, most severe
Can I keep running with it?
Stop now
Shut down and fix before working on. Running on risks damage or the machine locks out.
What should I check first?
Shut down and check the surge tank when cold; add coolant only after finding the loss
Then 3 more checksWhere to read it
Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.
Checks
0 of 4 done
Causes
- Coolant lost through a hose, radiator, heater core or water pump seal
- Head gasket or EGR cooler leak pushing coolant out of the system
- Level sensor wiring shorted so the ECU thinks the tank is empty
How it failed
You'll notice: Red stop lamp lights, the engine derates and a low coolant message may show.
Real conditionRead from FMI 1: data below normal, most severe
The sensor reading is valid but outside the allowed range - the problem may be real.
- Meter test
- Check the real value with a separate gauge or thermometer before blaming the sensor.
- Good result
- If the gauge agrees with the display, fix the machine, not the sensor.
When to stop
Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Coolant level and coolant temperature sensors
2 other codes on this part are also real condition (MID 128 PID 110 FMI 0, MID 128 PID 110 FMI 16). When they show together, start at the wiring and connector they share.
- MID 128 PID 110 FMI 0Engine coolant temperature critically highReal conditionStop now
- MID 128 PID 110 FMI 2Engine coolant temperature signal erraticErratic or implausibleCheck soon
- MID 128 PID 110 FMI 4Engine coolant temperature sensor signal low or shorted to groundShorted lowCheck soon
- MID 128 PID 110 FMI 5Engine coolant temperature sensor circuit openOpen circuitCheck soon
- MID 128 PID 110 FMI 16Engine coolant temperature moderately highReal conditionCheck soon
- MID 128 PID 111 FMI 1Engine coolant level critically lowReal conditionStop now
- MID 128 PID 111 FMI 3Coolant level sensor circuit shorted to positiveShorted highCheck soon
- MID 128 PID 111 FMI 4Coolant level sensor circuit shorted to groundShorted lowCheck soon
- MID 128 PID 111 FMI 5Coolant level sensor circuit openOpen circuitCheck soon
Other Volvo/Mack codes: MID 128 engine ECU - sensors and levels
- MID 128 SID 33 FMI 3Fan clutch output shorted high - fan runs full speed
- MID 128 SID 33 FMI 4Fan clutch output shorted low
- MID 128 SID 33 FMI 5Fan clutch output circuit open
- MID 128 PID 98 FMI 1Engine oil level critically low
- MID 128 PID 98 FMI 4Engine oil level sensor shorted to ground
- MID 128 PID 98 FMI 5Engine oil level sensor circuit open
- MID 128 PID 100 FMI 1Engine oil pressure critically low
Related on Equipments Finder
Source
This source lists MID 128 PID 111 FMI 1 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Mack MP7/MP8/MP10 engines (CHU, CXU, GU, TD) with the 2010-and-later MID 128 engine ECU; the same MID 128 numbers appear on Volvo D11/D13 engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
