EF Logo

Volvo/Mack · MID 128 engine ECU - aftertreatment (DPF, DEF, NOx)

Volvo/Mack NOx sensors before and after the SCR fault codes

Two NOx sensors in the exhaust are read by the engine ECU on MID 128 over CAN. The inlet sensor (PPID 348) before the SCR catalyst measures raw engine NOx.

More about these parts

The outlet sensor (PPID 270) after the catalyst measures what leaves the exhaust. The ECU compares the two to check SCR efficiency and DEF dosing.

FaultCheckMID 128PPID 270FMI 9Volvo/Mack · NOx sensors before and after the SCR
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.

What do these codes mean?

Volvo/Mack codes MID 128 PPID 270 FMI 2 to MID 128 PPID 348 FMI 9 are all about the nOx sensors before and after the SCR. The most common failure type is erratic or implausible (2 of 6); none needs an immediate stop. Start with this check: inspect the sensor connector and harness at the engine end for the inlet and at the tailpipe end for the outlet.

How urgent are they?

None of the 6 codes here means stop now; all 6 can wait until the shift ends, but find the cause before the next one.

  • Check soon6

What should I check first?

Inspect the sensor connector and harness at the engine end for the inlet and at the tailpipe end for the outlet

Shared checks

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Volvo/Mack MID 128 PPID 270 FMI 2Outlet NOx sensor reading not plausible

    The outlet NOx sensor reading does not agree with the inlet NOx sensor or with the DEF dosing.· Erratic or implausible
    Check soon

    Causes

    • Outlet NOx sensor aging or failed
    • Engine-out NOx too high from an EGR fault
    • Poor quality DEF or wrong fluid in the tank

    Checks

    1. 1Compare inlet and outlet NOx readings in the scan tool with the engine at steady load
    2. 2Check DEF quality with a refractometer for damage, corrosion or looseness
    3. 3Look for EGR and intake faults that raise engine-out NOx
    4. 4Replace the NOx sensor only after DEF quality and EGR are cleared
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Volvo/Mack MID 128 PPID 270 FMI 3Outlet NOx sensor signal shorted high

    The NOx signal between the outlet sensor and its control unit reads as shorted to a supply.· Shorted high
    Check soon

    Causes

    • Sensor wire shorted to a supply wire
    • Faulty outlet NOx sensor
    • Damaged connector at the sensor control unit

    Checks

    1. 1Look at the sensor lead and its connector for chafing against the exhaust
    2. 2Check the NOx signal wire for a short to a supply wire with the key off
    3. 3Check the supply voltage at the sensor control unit
    4. 4Replace the sensor if the lead is intact and confirm the code does not return
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Volvo/Mack MID 128 PPID 270 FMI 5Outlet NOx sensor circuit open

    The NOx signal circuit between the outlet sensor and its control unit is open.· Open circuit
    Check soon

    Causes

    • Open wire in the sensor lead
    • Faulty outlet NOx sensor
    • Pin pushed back at the sensor connector

    Checks

    1. 1Check continuity of each sensor lead wire to the control unit
    2. 2Inspect the connector for corrosion and pushed pins
    3. 3Check for a damaged lead near the exhaust heat
    4. 4Replace the sensor after the wiring checks out
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Volvo/Mack MID 128 PPID 270 FMI 9Outlet NOx sensor signal missing

    The engine ECM lost communication with the outlet NOx sensor, which sits after the SCR catalyst.· Lost message
    Check soon

    Causes

    • Outlet NOx sensor unplugged, wiring broken or connector corroded
    • NOx sensor control unit failed
    • Low or unstable supply voltage to the NOx sensor

    Checks

    1. 1Check the outlet NOx sensor connector for water, melted pins and a loose lock
    2. 2Measure battery voltage and ground at the sensor connector with the key on
    3. 3Check the CAN wires to the sensor for continuity and for shorts to ground
    4. 4Look for a loose ground strap on the aftertreatment frame
    5. 5Replace the sensor if power and data link are proven good
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • Volvo/Mack MID 128 PPID 348 FMI 2Inlet NOx sensor not plausible

    The inlet NOx sensor value fails the plausibility check.· Erratic or implausible
    Check soon

    Causes

    • Inlet NOx sensor faulty or aged
    • Engine-out NOx high from an EGR fault
    • Corroded or loose connector on the sensor

    Checks

    1. 1Compare inlet NOx with the expected values for the load in the scan tool
    2. 2Check the EGR system operation and valve position
    3. 3Check the sensor connector for corrosion for damage, corrosion or looseness
    4. 4Replace the sensor if EGR and wiring are good
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Volvo/Mack MID 128 PPID 348 FMI 9Inlet NOx sensor signal missing

    The engine ECM lost communication with the inlet NOx sensor ahead of the SCR catalyst.· Lost message
    Check soon

    Causes

    • Inlet NOx sensor unplugged or connector corroded
    • NOx sensor control unit failed
    • Wiring fault between the control unit and the engine ECM

    Checks

    1. 1Check the inlet NOx sensor connector and its lock
    2. 2Check power and ground at the sensor connector
    3. 3Check the data wires for continuity and shorts
    4. 4Replace the sensor if its supply and data link are good
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

Shared checks

Checks, in order

  1. 1Inspect the sensor connector and harness at the engine end for the inlet and at the tailpipe end for the outlet
  2. 2Measure the heater and supply voltage and ground at the sensor plug with the key on
  3. 3Compare the inlet and outlet readings at the same engine load
  4. 4Look for exhaust leaks near either sensor
  5. 5Replace a sensor only once its wiring and the CAN link are proven good

Causes

  • NOx sensor failed or contaminated
  • Harness or connector fault at the sensor
  • CAN communication fault between the sensor control unit and the engine ECU
  • Exhaust leak near the sensor letting outside air upset the reading

Most common here: erratic or implausible (2 of 6)

Watch the live value on the service tool while you flex the harness and tap the connector.

When to stop

You'll notice: A check lamp comes on and DEF dosing may be limited.

Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.