EF Logo

Volvo/Mack · MID 128 engine ECU - fuel, injectors and timing

Volvo/Mack Injector circuits (cylinders 1-6) fault codes

Each cylinder has an electronic injector driven by the engine ECU. Codes are numbered by cylinder through SID 1 to 6, and cover circuit faults and fuelling faults on that injector.

FaultCheckMID 128SID 1FMI 3Volvo/Mack · Injector circuits (cylinders 1-6)
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.

What do these codes mean?

Volvo/Mack codes MID 128 SID 1 FMI 3 to MID 128 SID 6 FMI 5 are all about the injector circuits (cylinders 1-6). Most are open circuit faults; none needs an immediate stop. Start with this check: check the injector harness and connector under the valve cover for chafing and oil.

How urgent are they?

None of the 10 codes here means stop now; all 10 can wait until the shift ends, but find the cause before the next one.

  • Check soon10

What should I check first?

Check the injector harness and connector under the valve cover for chafing and oil

Shared checks

10 of 10

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Volvo/Mack MID 128 SID 1 FMI 3Injector cylinder 1 circuit shorted high

    The ECM sees a short to positive on the low-side circuit of the cylinder 1 injector.· Shorted high
    Check soon

    Causes

    • Injector harness for cylinder 1 shorted to positive on the low-side wire
    • Injector solenoid with an internal short
    • Chafed wire under the valve cover where the harness crosses the rocker area

    Checks

    1. 1Read the code active or inactive and note whether it returns after a clear and restart
    2. 2Unplug the cylinder 1 injector connector and check both wires for voltage with the key on; there should be none
    3. 3Measure injector coil resistance and compare it with a good cylinder on the same engine
    4. 4Inspect the harness under the valve cover for chafing and oil soaked insulation
    5. 5Swap the injector wires with a neighbouring cylinder only if the manual allows, to see if the fault follows
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Volvo/Mack MID 128 SID 1 FMI 5Injector cylinder 1 circuit open or shorted to ground

    Cylinder 1 injector has an open circuit, or the high and low sides are shorted together or to ground.· Open circuit
    Check soon

    Causes

    • Open high-side or low-side wire to the cylinder 1 injector
    • High and low wires shorted together
    • Low-side wire shorted to ground
    • Injector connector pin backed out or corroded
    • Failed injector solenoid

    Checks

    1. 1Unplug the cylinder 1 injector and measure resistance across its two pins; infinite means open coil
    2. 2Check each wire to ground with the key off for a short
    3. 3Check continuity of both wires between the injector connector and the ECM
    4. 4Inspect the injector connector for pushed pins and oil contamination
    5. 5Replace the injector only if the harness proves good
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Volvo/Mack MID 128 SID 1 FMI 7Injector cylinder 1 balancing above limit

    Cylinder 1 is being corrected by more than the allowed amount in cylinder balancing.· Part or controller
    Check soon

    Causes

    • Cylinder 1 fuel injector worn or sticking
    • Low compression on cylinder 1
    • Damaged flywheel affecting speed readings
    • PTO engaged without the ECM knowing

    Checks

    1. 1Check whether the PTO or another load was engaged when the code set
    2. 2Run a cylinder cut-out or balance test in the scan tool and see which cylinder is the odd one
    3. 3Compare cylinder 1 compression with the others
    4. 4Inspect the flywheel and ring gear teeth for damage
    ControllerPartSupplySignalGround?
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Check power and ground at the module connector with the key on, then its fuses.

    Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

  • Volvo/Mack MID 128 SID 1 FMI 8Injector cylinder 1 misfire detected

    A misfire has been detected on cylinder 1.· Erratic or implausible
    Check soon

    Causes

    • Cylinder 1 injector clogged or faulty
    • Weak cylinder 1 compression
    • Poor fuel quality blocking the nozzle

    Checks

    1. 1Run a cylinder balance test and confirm cylinder 1 is the weak one
    2. 2Check fuel quality and the condition of the fuel filters
    3. 3Compare cylinder 1 compression with the other cylinders
    4. 4Replace or test the cylinder 1 injector if the balance test points at it
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • Volvo/Mack MID 128 SID 1 FMI 13Injector cylinder 1 out of calibration

    The cylinder 1 balancing data is above its limit, and Mack lists the same causes as the mechanical fault: a worn injector, low compression or a damaged flywheel.· Part or controller
    Check soon

    Causes

    • Faulty cylinder 1 injector
    • Low cylinder 1 compression
    • Damaged flywheel

    Checks

    1. 1Clear the code and re-run the balance test to see if it returns
    2. 2Check compression on cylinder 1 against the other cylinders
    3. 3Inspect the flywheel ring gear for damage for damage, corrosion or looseness
    4. 4Test or replace the cylinder 1 injector and write down the reading
    ControllerPartSupplySignalGround?
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Check power and ground at the module connector with the key on, then its fuses.

    Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

  • Volvo/Mack MID 128 SID 2 FMI 5Injector cylinder 2 circuit open or shorted

    The ECM sees the cylinder 2 injector circuit as open, or the high and low sides shorted together or to ground.· Open circuit
    Check soon

    Causes

    • Open wire to the cylinder 2 injector
    • Injector wires shorted to each other or ground
    • Cylinder 2 injector solenoid failed
    • Connector fault at the valve cover feed-through

    Checks

    1. 1Measure the resistance of the cylinder 2 injector coil at its connector and compare with another cylinder
    2. 2Test both injector wires for a short to ground with the key off
    3. 3Check continuity of both wires from the injector plug to the ECM connector
    4. 4Look at the valve cover feed-through connector for oil and corrosion
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Volvo/Mack MID 128 SID 3 FMI 5Injector cylinder 3 circuit open or shorted

    The cylinder 3 injector circuit is open or shorted high side to low side or to ground.· Open circuit
    Check soon

    Causes

    • Open circuit at cylinder 3 injector wiring
    • Harness chafed against the head or rocker area
    • Failed injector solenoid
    • ECM driver output fault if several injectors set codes

    Checks

    1. 1Unplug cylinder 3 injector and read coil resistance
    2. 2Check both wires for continuity to the ECM and for shorts to ground
    3. 3Look for chafing where the harness passes the head
    4. 4If several injector codes appear together, suspect the shared harness or ECM driver before replacing injectors
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Volvo/Mack MID 128 SID 4 FMI 5Injector cylinder 4 circuit open or shorted

    The cylinder 4 injector circuit is open, or the wires are shorted together or to ground, so the ECM cannot fire that cylinder properly.· Open circuit
    Check soon

    Causes

    • Open wire or backed-out pin at the cylinder 4 injector connector
    • Injector coil failed
    • Wires shorted to each other in the harness

    Checks

    1. 1Measure cylinder 4 injector coil resistance at its connector and compare it with another cylinder
    2. 2Test for a short between the two injector wires and to ground
    3. 3Check harness continuity to the ECM connector
    4. 4Inspect the injector connector terminals for fretting
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Volvo/Mack MID 128 SID 5 FMI 5Injector cylinder 5 circuit open or shorted

    The ECM reads the cylinder 5 injector circuit as open or shorted high to low or to ground.· Open circuit
    Check soon

    Causes

    • Broken wire in the cylinder 5 injector harness
    • Failed cylinder 5 injector coil
    • Short to ground at a worn harness spot

    Checks

    1. 1Check the injector coil resistance with the connector unplugged
    2. 2Test wire-to-wire and wire-to-ground isolation with the key off
    3. 3Wiggle test the harness at the valve cover while monitoring the live status
    4. 4Replace the injector only if the circuit tests good
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • Volvo/Mack MID 128 SID 6 FMI 5Injector cylinder 6 circuit open or shorted

    The cylinder 6 injector circuit is open or shorted.· Open circuit
    Check soon

    Causes

    • Open circuit in the cylinder 6 injector wiring
    • Injector coil open or shorted
    • Connector fault at the rear of the engine harness

    Checks

    1. 1Measure the cylinder 6 injector coil resistance
    2. 2Test the two wires for continuity and for any short to ground
    3. 3Inspect the connector at the rear of the head for oil and corrosion
    4. 4Check the harness route near hot components for burned insulation
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

Shared checks

Checks, in order

  1. 1Check the injector harness and connector under the valve cover for chafing and oil
  2. 2Measure the injector coil resistance against the service data
  3. 3Run a cylinder cutout or balance test with the scan tool
  4. 4Swap injectors between cylinders to see if the fault follows

Causes

  • Injector solenoid failed or damaged wiring harness
  • Chafed wire under the valve cover
  • Poor connector contact at the injector

Most codes here: open circuit (6 of 10)

Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

When to stop

You'll notice: The engine misfires, runs rough, loses power or smokes, and a check lamp comes on.

Common-rail fuel runs at very high pressure. Never open a high-pressure line or fitting with the engine running or just after it stops - a fine fuel jet can pierce skin.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.