John Deere · Monitor controller (DSZ) - alarms
John Deere Engine, overheat, fuel and water alarms on the monitor fault codes
The monitor shows engine alarms that the engine controller (ECU) detects and passes on over CAN: engine oil pressure, intake air, boost, fuel and EGR temperatures, coolant overheat and sensor circuit shorts, fuel filter restriction, water in the fuel separator, and engine protection shutdown. The alarm tells you what the ECU saw; the ECU codes behind it give the exact cause.
Where this code shows
Turn the key on and open the monitor's diagnostic/fault screen.
What do these codes mean?
John Deere codes ECU 000097.03 to ICZ 20149.02 are all about the engine, overheat, fuel and water alarms on the monitor. The most common failure type is real condition (9 of 24); 3 need an immediate stop. Start with this check: stop the engine for oil pressure and overheat alarms, then check oil level, coolant level and the real pressure or temperature.
How urgent are they?
3 of 24 codes here mean stop now; the other 21 can wait until the shift ends, but find the cause before the next one.
- Stop now3
- Check soon21
What should I check first?
Stop the engine for oil pressure and overheat alarms, then check oil level, coolant level and the real pressure or temperature
Shared checks24 of 24
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
John Deere ECU 000097.03Water in fuel sensor voltage high
The ECU reads the water-in-fuel sensor signal at its high limit, usually a short or fault in the sensor circuit. The operator may see a water in fuel warning that does not clear after draining.· Shorted highShorted highCheck soonCauses
- Water-in-fuel sensor wire shorted to its supply inside the filter head connector
- Sensor failed with its output stuck high
- Corroded or wet sensor plug bridging the pins
- Water-in-fuel circuit open at the ground side, letting the signal float high
Checks
- 1Drain the water separator bowl first; if the warning stays after the bowl is dry, suspect the circuit and not the fuel
- 2Unplug the water-in-fuel sensor and see whether the code changes to an open-circuit condition
- 3Measure the sensor supply and ground at its plug with the key on
- 4Inspect the plug on the filter head for water, corrosion and bent pins
- 5Replace the sensor or filter head sensor only after the wiring passes
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
John Deere ECU 000097.04Water in fuel separator full
The ECU reports the water in fuel separator is full, meaning water has collected in the fuel system. The operator may see a warning and ignoring it can damage injectors and the high pressure pump.· Lost messageLost messageCheck soonCauses
- Water collected in the fuel system from condensation or contaminated fuel
- Separator bowl not drained at the service interval
- Water getting in through a loose tank cap or a damaged tank vent
- Poor fuel quality from the supplier
Checks
- 1Drain the water separator bowl and watch what comes out; a lot of water means the tank is contaminated
- 2Check the fuel tank drain for water and sediment
- 3Check the tank cap seal and the vent for damage that lets in rain or washing water
- 4Replace the fuel filter if the bowl has been full for a long time
- 5Bleed the fuel system and watch for the warning to clear
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
John Deere ECU 001110.31Engine protection shutdown
The engine protection system shut the engine down, so the engine stops and the operator may see a protection shutdown message. The actual cause is another condition logged at the same time.· OtherOtherStop nowCauses
- Low oil pressure or high coolant temperature that triggered the shutdown
- Engine overspeed or another engine protection fault
- Failed sensor feeding a false value to the protection logic
- Coolant level too low
Checks
- 1Read all active and stored ECU codes to find the condition that caused the shutdown
- 2Check the engine oil level, coolant level and engine temperature before restarting
- 3Test the sensors named by the accompanying codes and their wiring
- 4Clear this code only after the real fault has been repaired
- 5Do not override the protection until the cause is clear
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
John Deere DSZ 13310.03Shorted circuit in coolant temperature sensor
The monitor reports a short circuit on the coolant temperature sensor; the source marks this as not applicable to this machine, so treat it as unlikely on that model.· Short circuitShort circuitCheck soonCauses
- Wire to the engine overheat and coolant temperature chafed through and touching ground or a supply wire
- Water or oil inside the engine overheat and coolant temperature connector bridging pins
- Internal short inside the engine overheat and coolant temperature
Checks
- 1Unplug the engine overheat and coolant temperature and see whether the code changes from a short to an open; if it does, the part is the likely culprit
- 2Measure each wire to ground with both ends disconnected; a low reading means a harness short
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the part and the controller. Measure from the output wire to ground and to battery positive, then across the part.
Good: Open circuit (OL) to ground and to supply; the part reads its listed resistance, not near 0 Ω.
John Deere ICZ 13310.03Shorted circuit in coolant temperature sensor
The information controller (ICZ) list carries the same code as the monitor (DSZ) list. The monitor reports a short circuit on the coolant temperature sensor; the source marks this as not applicable to this machine, so treat it as unlikely on that model.· Short circuitShort circuitCheck soonCauses
- Wire to the engine overheat and coolant temperature chafed through and touching ground or a supply wire
- Water or oil inside the engine overheat and coolant temperature connector bridging pins
- Internal short inside the engine overheat and coolant temperature
Checks
- 1Unplug the engine overheat and coolant temperature and see whether the code changes from a short to an open; if it does, the part is the likely culprit
- 2Measure each wire to ground with both ends disconnected; a low reading means a harness short
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the part and the controller. Measure from the output wire to ground and to battery positive, then across the part.
Good: Open circuit (OL) to ground and to supply; the part reads its listed resistance, not near 0 Ω.
John Deere ICZ 13334.02Radiator coolant error
The information controller reports a radiator coolant error, so the coolant temperature or level signal is abnormal.· OtherOtherCheck soonCauses
- The real condition the engine overheat and coolant temperature monitors is present
- Switch or sensor of the engine overheat and coolant temperature failing or wired wrongly
- Harness or connector fault between the input and the monitor
Checks
- 1Confirm the real condition at the engine overheat and coolant temperature on the machine before replacing parts
- 2Check the switch or sensor plug and wiring for the engine overheat and coolant temperature
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
John Deere DSZ 20100.02Overheat alarm
The monitor raised an overheat alarm; the source marks this code as not applicable to this machine, so check which controller version your machine has.· Real conditionReal conditionCheck soonCauses
- The real condition the engine overheat and coolant temperature monitors is present
- Switch or sensor of the engine overheat and coolant temperature failing or wired wrongly
- Harness or connector fault between the input and the monitor
Checks
- 1Confirm the real condition at the engine overheat and coolant temperature on the machine before replacing parts
- 2Check the switch or sensor plug and wiring for the engine overheat and coolant temperature
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
John Deere DSZ 20101.02Engine warning alarm
The monitor shows a general engine warning that the engine controller (ECU) raised over CAN. The alarm carries no detail of its own; the real code is held in the ECU.· Lost messageLost messageCheck soonCauses
- An active ECU fault code that raised the warning
- The ECU keeps sending the warning while its cause persists
- A CAN fault leaving a stale warning on the monitor
Checks
- 1Read the active ECU codes on the diagnostic screen; that code, not this alarm, is the one to fix
- 2Clear after the repair and run the engine to see whether the warning returns
- 3If no ECU code is active, check the CAN link between the ECU and the monitor
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
John Deere ICZ 20101.02Engine warning alarm
The information controller (ICZ) list carries the same code as the monitor (DSZ) list. The monitor shows a general engine warning that the engine controller (ECU) raised over CAN. The alarm carries no detail of its own; the real code is held in the ECU.· Lost messageLost messageCheck soonCauses
- An active ECU fault code that raised the warning
- The ECU keeps sending the warning while its cause persists
- A CAN fault leaving a stale warning on the monitor
Checks
- 1Read the active ECU codes on the diagnostic screen; that code, not this alarm, is the one to fix
- 2Clear after the repair and run the engine to see whether the warning returns
- 3If no ECU code is active, check the CAN link between the ECU and the monitor
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
John Deere DSZ 20102.02Engine oil pressure alarm
The monitor shows an engine oil pressure alarm, meaning the pressure switch or signal says oil pressure is low. Running the engine on with real low oil pressure can quickly destroy the bearings.· Lost messageLost messageStop nowCauses
- Engine oil level low or the oil diluted
- Worn engine bearings or a failing oil pump
- Oil pressure switch or sensor faulty
- Wiring fault grounding the oil pressure switch circuit
Checks
- 1Stop the engine and check the oil level and condition
- 2Check the real oil pressure with a mechanical gauge at the engine test port
- 3Unplug the switch and see whether the alarm clears
- 4Check the oil pressure switch wire for a short to ground along the engine harness
- 5Do not restart the engine until the pressure has been verified
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
John Deere ICZ 20102.02Engine oil pressure alarm
The information controller (ICZ) list carries the same code as the monitor (DSZ) list. The monitor shows an engine oil pressure alarm, meaning the pressure switch or signal says oil pressure is low. Running the engine on with real low oil pressure can quickly destroy the bearings.· Lost messageLost messageStop nowCauses
- Engine oil level low or the oil diluted
- Worn engine bearings or a failing oil pump
- Oil pressure switch or sensor faulty
- Wiring fault grounding the oil pressure switch circuit
Checks
- 1Stop the engine and check the oil level and condition
- 2Check the real oil pressure with a mechanical gauge at the engine test port
- 3Unplug the switch and see whether the alarm clears
- 4Check the oil pressure switch wire for a short to ground along the engine harness
- 5Do not restart the engine until the pressure has been verified
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
John Deere DSZ 20107.02Water separator alarm
The fuel water separator signal is active, meaning water has collected in the fuel filter bowl. Water in diesel can damage injectors and the high pressure pump, and the operator may see a warning on the monitor.· Lost messageLost messageCheck soonCauses
- Water in the fuel from condensation or a bad fuel source
- Water separator full and not drained
- Water sensor faulty
Checks
- 1Drain the water separator bowl and see whether the alarm clears
- 2Inspect the fuel in the bowl for water and contamination
- 3Check the water sensor wiring and connector at the filter housing for damage and water
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
John Deere DSZ 20110.02Fuel filter restriction alarm
The fuel filter looks restricted, so the fuel supply may not keep up under load. Diagnose ECU code 000094.17 per the engine manual.· Real conditionReal conditionCheck soonCauses
- Fuel filter blocked
- Fuel supply line kinked
- Fuel pressure sensor faulty
- Contaminated fuel
Checks
- 1Replace the fuel filter and bleed the system following the engine manual
- 2Check the fuel supply lines for kinks, collapsed hoses and air leaks
- 3Read ECU code 000094.17 per the engine manual
- 4Check the fuel quality in the tank for water, wax and contamination
- 5Check the fuel supply pressure with a gauge at the filter housing
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
John Deere ICZ 20110.02Fuel filter restriction alarm
The information controller (ICZ) list carries the same code as the monitor (DSZ) list. The fuel filter looks restricted, so the fuel supply may not keep up under load. Diagnose ECU code 000094.17 per the engine manual.· Real conditionReal conditionCheck soonCauses
- Fuel filter blocked
- Fuel supply line kinked
- Fuel pressure sensor faulty
Checks
- 1Replace the fuel filter and bleed the system following the engine manual
- 2Check the fuel supply lines for kinks, collapsed hoses and air leaks
- 3Read ECU code 000094.17 per the engine manual
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
John Deere DSZ 20114.02Overheat alarm
The monitor reports an overheat alarm, meaning the engine coolant or another monitored temperature is above its limit.· Real conditionReal conditionCheck soonCauses
- The real condition the engine overheat and coolant temperature monitors is present
- Switch or sensor of the engine overheat and coolant temperature failing or wired wrongly
- Harness or connector fault between the input and the monitor
Checks
- 1Confirm the real condition at the engine overheat and coolant temperature on the machine before replacing parts
- 2Check the switch or sensor plug and wiring for the engine overheat and coolant temperature
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
John Deere ICZ 20114.02Overheat alarm
The information controller (ICZ) list carries the same code as the monitor (DSZ) list. The monitor reports an overheat alarm, meaning the engine coolant or another monitored temperature is above its limit.· Real conditionReal conditionCheck soonCauses
- The real condition the engine overheat and coolant temperature monitors is present
- Switch or sensor of the engine overheat and coolant temperature failing or wired wrongly
- Harness or connector fault between the input and the monitor
Checks
- 1Confirm the real condition at the engine overheat and coolant temperature on the machine before replacing parts
- 2Check the switch or sensor plug and wiring for the engine overheat and coolant temperature
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
John Deere DSZ 20142.02Intake air temperature alarm
The ECU reports the intake air temperature as too high and the monitor shows the alarm. Hot intake air lowers power and raises exhaust temperature.· Real conditionReal conditionCheck soonCauses
- Radiator or charge air cooler blocked with dust or chaff
- Cooling fan or coolant not keeping the intake air cool
- Intake air temperature sensor reading high from an open circuit or a poor plug
Checks
- 1Clean the charge air cooler and radiator fins, and check for oil in the intercooler
- 2Compare the monitor intake air temperature with a temperature gun reading on the intake pipe
- 3Unplug the intake air temperature sensor and check its resistance and plug for corrosion
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
John Deere ICZ 20142.02Intake air temperature alarm
The information controller (ICZ) list carries the same code as the monitor (DSZ) list. The ECU reports the intake air temperature as too high and the monitor shows the alarm. Hot intake air lowers power and raises exhaust temperature.· Real conditionReal conditionCheck soonCauses
- Radiator or charge air cooler blocked with dust or chaff
- Cooling fan or coolant not keeping the intake air cool
- Intake air temperature sensor reading high from an open circuit or a poor plug
Checks
- 1Clean the charge air cooler and radiator fins, and check for oil in the intercooler
- 2Compare the monitor intake air temperature with a temperature gun reading on the intake pipe
- 3Unplug the intake air temperature sensor and check its resistance and plug for corrosion
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
John Deere DSZ 20145.02Boost temperature increase alarm
The ECU reports that boost air temperature after the turbocharger has risen too far, and the monitor shows the alarm.· OtherOtherCheck soonCauses
- Charge air cooler restricted or leaking
- Turbocharger working too hard against an intake or exhaust restriction
- Boost temperature sensor reading wrong
Checks
- 1Inspect the charge air cooler core and hoses for leaks, oil and blockage
- 2Check the air cleaner and exhaust for restriction that makes the turbo work harder
- 3Compare boost temperature with intake air temperature on a cold engine; a large gap points at the sensor
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
John Deere ICZ 20145.02Boost temperature increase alarm
The information controller (ICZ) list carries the same code as the monitor (DSZ) list. The ECU reports that boost air temperature after the turbocharger has risen too far, and the monitor shows the alarm.· OtherOtherCheck soonCauses
- Charge air cooler restricted or leaking
- Turbocharger working too hard against an intake or exhaust restriction
- Boost temperature sensor reading wrong
Checks
- 1Inspect the charge air cooler core and hoses for leaks, oil and blockage
- 2Check the air cleaner and exhaust for restriction that makes the turbo work harder
- 3Compare boost temperature with intake air temperature on a cold engine; a large gap points at the sensor
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Read the code with the service tool and note which other codes are active with it.
Good: Codes that appear together usually share one cause - start with the wiring they share.
John Deere DSZ 20146.02Fuel temperature increase alarm
The ECU reports that the fuel temperature has risen too far, and the monitor shows the alarm. Hot fuel is thinner and can reduce power.· Lost messageLost messageCheck soonCauses
- Hot fuel returning from the injection system on a hot day or with a blocked cooler
- Fuel cooler or lines blocked
- Fuel temperature sensor or wiring fault
Checks
- 1Feel the fuel return line and filter housing; very hot fuel on a cool engine means a restriction or a sensor fault
- 2Check the fuel cooler, if fitted, for dirt and airflow
- 3Check the fuel temperature sensor plug and its resistance against the manual table
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
John Deere ICZ 20146.02Fuel temperature increase alarm
The information controller (ICZ) list carries the same code as the monitor (DSZ) list. The ECU reports that the fuel temperature has risen too far, and the monitor shows the alarm. Hot fuel is thinner and can reduce power.· Lost messageLost messageCheck soonCauses
- Hot fuel returning from the injection system on a hot day or with a blocked cooler
- Fuel cooler or lines blocked
- Fuel temperature sensor or wiring fault
Checks
- 1Feel the fuel return line and filter housing; very hot fuel on a cool engine means a restriction or a sensor fault
- 2Check the fuel cooler, if fitted, for dirt and airflow
- 3Check the fuel temperature sensor plug and its resistance against the manual table
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
John Deere DSZ 20149.02EGR gas temperature alarm
The ECU reports that the EGR gas temperature is too high, and the monitor shows the alarm.· Real conditionReal conditionCheck soonCauses
- EGR cooler fouled or leaking coolant
- EGR valve stuck open or closed, changing the gas temperature
- EGR gas temperature sensor or its wiring faulty
Checks
- 1Read the EGR valve position and gas temperature on the ECU service screen at idle and under load
- 2Look for white smoke or coolant loss that suggests an EGR cooler leak
- 3Check the EGR temperature sensor plug and its resistance
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
John Deere ICZ 20149.02EGR gas temperature alarm
The information controller (ICZ) list carries the same code as the monitor (DSZ) list. The ECU reports that the EGR gas temperature is too high, and the monitor shows the alarm.· Real conditionReal conditionCheck soonCauses
- EGR cooler fouled or leaking coolant
- EGR valve stuck open or closed, changing the gas temperature
- EGR gas temperature sensor or its wiring faulty
Checks
- 1Read the EGR valve position and gas temperature on the ECU service screen at idle and under load
- 2Look for white smoke or coolant loss that suggests an EGR cooler leak
- 3Check the EGR temperature sensor plug and its resistance
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Shared checks
Checks, in order
- 1Stop the engine for oil pressure and overheat alarms, then check oil level, coolant level and the real pressure or temperature
- 2Read the active ECU codes behind the alarm; they name the sensor and failure
- 3For fuel alarms drain the water separator and check the fuel filter before suspecting the sensor
- 4Confirm the switch or sensor plug and wiring for the alarm named, with both ends unplugged
- 5Clear the code after the repair and run the machine to see if the alarm returns
Causes
- The real condition is present: low oil, overheating, restricted or watery fuel
- Switch or sensor behind the alarm failing or wired wrongly
- Wire shorted to ground or supply between the input and the monitor
- Cooler, filter or separator that has not been serviced
Most common here: real condition (9 of 24)
Check the real value with a separate gauge or thermometer before blaming the sensor.
When to stop
You'll notice: An alarm symbol appears, the engine may derate or shut down, and running on after an oil pressure or overheat alarm can damage the engine.
Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
- Excavator Fault Codes - John Deere excavators fault codes list (MCZ/ECU/DSZ)
- Inside the Yard - John Deere fault codes list (ECU engine codes)
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
