John Deere · Monitor controller (DSZ) - alarms
John Deere Fault Code DSZ 20102.02
Engine oil pressure alarm
What does John Deere code DSZ 20102.02 mean?
The monitor shows an engine oil pressure alarm, meaning the pressure switch or signal says oil pressure is low. Running the engine on with real low oil pressure can quickly destroy the bearings. Urgency: stop now - shut down and fix before working on. Check first: stop the engine and check the oil level and condition.
- DSZ
- Which controller reports it
- 20102
- What is at fault
- .02
- How it failed
Can I keep running with it?
Stop now
Shut down and fix before working on. Running on risks damage or the machine locks out.
What should I check first?
Stop the engine and check the oil level and condition
Then 4 more checksWhere this code shows
Turn the key on and open the monitor's diagnostic/fault screen.
Checks
0 of 5 done
Causes
- Engine oil level low or the oil diluted
- Worn engine bearings or a failing oil pump
- Oil pressure switch or sensor faulty
- Wiring fault grounding the oil pressure switch circuit
How it failed
You'll notice: The monitor shows an engine oil pressure alarm.
Lost messageRead from how the source describes the code
A module stopped hearing another on the data link, or the data came late or garbled.
- Meter test
- Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
- Good result
- About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
When to stop
Low oil pressure can wreck bearings in minutes. Stop the engine and check the level before restarting; if the level is right, do not run it again until the pressure is checked with a gauge.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Engine, overheat, fuel and water alarms on the monitor
7 other codes on this part are also lost message (ECU 000097.04, DSZ 20101.02, ICZ 20101.02, ICZ 20102.02 and more). When they show together, start at the wiring and connector they share.
- ICZ 13334.02Radiator coolant errorOtherCheck soon
- DSZ 20100.02Overheat alarmReal conditionCheck soon
- DSZ 20101.02Engine warning alarmLost messageCheck soon
- ICZ 20101.02Engine warning alarmLost messageCheck soon
- DSZ 20102.02Engine oil pressure alarmLost messageStop now
- ICZ 20102.02Engine oil pressure alarmLost messageStop now
- DSZ 20107.02Water separator alarmLost messageCheck soon
- DSZ 20110.02Fuel filter restriction alarmReal conditionCheck soon
- ICZ 20110.02Fuel filter restriction alarmReal conditionCheck soon
Show the other 15 codesHide the other codes
- ECU 000097.03Water in fuel sensor voltage highShorted highCheck soon
- ECU 000097.04Water in fuel separator fullLost messageCheck soon
- ECU 001110.31Engine protection shutdownOtherStop now
- DSZ 13310.03Shorted circuit in coolant temperature sensorShort circuitCheck soon
- ICZ 13310.03Shorted circuit in coolant temperature sensorShort circuitCheck soon
- DSZ 20114.02Overheat alarmReal conditionCheck soon
- ICZ 20114.02Overheat alarmReal conditionCheck soon
- DSZ 20142.02Intake air temperature alarmReal conditionCheck soon
- ICZ 20142.02Intake air temperature alarmReal conditionCheck soon
- DSZ 20145.02Boost temperature increase alarmOtherCheck soon
- ICZ 20145.02Boost temperature increase alarmOtherCheck soon
- DSZ 20146.02Fuel temperature increase alarmLost messageCheck soon
- ICZ 20146.02Fuel temperature increase alarmLost messageCheck soon
- DSZ 20149.02EGR gas temperature alarmReal conditionCheck soon
- ICZ 20149.02EGR gas temperature alarmReal conditionCheck soon
Other John Deere codes: Monitor controller (DSZ) - alarms
Related on Equipments Finder
Source
Excavator Fault Codes - John Deere excavators fault codes list (MCZ/ECU/DSZ)
This source lists DSZ 20102.02 and its meaning. The guidance on this page is general, not taken from it.
The source covers: John Deere G-series excavators (210G/210GLC and 350G class) with MCZ main controller; confirm against serial number.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
