EF Logo

JCB · Aftertreatment ECU - SCR / DEF

JCB DEF tank level and DEF tank temperature fault codes

The level sensor in the DEF tank head unit tells the SCR system how much DEF is left. Low or empty DEF triggers inducement.

More about these parts

The DEF tank temperature sensor tells the SCR system if the DEF is frozen or too hot.

FaultStopP203F-7BJCB · DEF tank level and DEF tank temperature
Code shows hereFAULTP203F-7B

Where this code shows

Switch the key on and note any warning lamp or fault icon on the cluster.

What do these codes mean?

JCB codes P203B-00 to P3413-87 are all about the dEF tank level and DEF tank temperature. The most common failure type is lost message (9 of 27); 1 needs an immediate stop. Start with this check: check the DEF level in the tank against the cluster reading.

How urgent are they?

1 of 27 codes here means stop now; the other 26 can wait until the shift ends, but find the cause before the next one.

  • Stop now1
  • Check soon26

What should I check first?

Check the DEF level in the tank against the cluster reading

Shared checks

27 of 27

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • JCB P203B-00DEF tank level signal error

    The DEF level signal is faulty but the code does not say high or low.· Erratic or implausible
    Check soon

    Causes

    • Level sensor in the DEF head unit failed
    • Poor connection at the head unit plug

    Checks

    1. 1Compare the live level value with the real level in the tank
    2. 2Check the head unit connector and wiring
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • JCB P203F-7BDEF tank empty

    The DEF tank is empty, so the SCR system cannot dose.· Real condition
    Stop now

    Causes

    • DEF tank run empty
    • DEF level sensor stuck at empty
    • Leak draining the tank
    • Pickup or suction line problem making the tank appear empty
    • Earlier low warnings ignored by the operator

    Checks

    1. 1Fill the tank with DEF of the correct grade and let the system recover
    2. 2Check the level on the display reads correctly after refilling
    3. 3Check the tank, hoses and DEF pump for leaks or wet marks
    4. 4Check the pickup and filter in the supply module for blockage
    5. 5Clear the fault and run the machine to confirm the derate is lifted
    6. 6Check that the system sees the new level and the inducement counter has stopped
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • JCB P203B-14DEF tank level signal below minimum voltage

    The DEF level sensor signal is below its minimum voltage, usually a short to ground in the level wiring, so the system cannot read DEF level and may start a low DEF warning.· Shorted low
    Check soon

    Causes

    • Level signal wire shorted to ground
    • Level sensor in the head unit shorted

    Checks

    1. 1Unplug the head unit; if the voltage rises, the sensor is the short, if not the wire
    2. 2Inspect the head unit connector for water
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • JCB P203B-15DEF tank level signal exceeds maximum voltage limit

    The DEF level signal exceeds the maximum voltage limit, which points to an open circuit or a short to supply in the level sensor wiring.· Shorted high
    Check soon

    Causes

    • Level sensor wire open or unplugged
    • Level signal shorted to a supply

    Checks

    1. 1Check continuity of the level signal wire to the head unit
    2. 2Inspect the head unit plug for a pushed-back pin
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • JCB P203B-16DEF tank level plausibility error

    The DEF level plausibility check failed: the level reading does not move the way DEF use and refills say it should, for example it stays fixed after a refill.· Erratic or implausible
    Check soon

    Causes

    • Level sensor float or element stuck in the head unit
    • Level reading offset from a damaged head unit

    Checks

    1. 1Refill with a known quantity and watch whether the level value rises
    2. 2Compare the reading with the level in the tank
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • JCB P203F-21DEF tank head unit level signal below minimum limit

    The DEF head unit level signal is below its minimum limit, which means the head unit itself reports an empty or invalid level.· Other
    Check soon

    Causes

    • Head unit level sensor failed low
    • Level really very low or empty

    Checks

    1. 1Check the real DEF level in the tank
    2. 2Compare the head unit value with a dipstick or visual check
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JCB P203B-22DEF tank level signal above maximum limit

    The DEF level signal is above its maximum limit: the sensor reads a tank that is fuller than possible, from an open circuit or a stuck sensor.· Open circuit
    Check soon

    Causes

    • Level sensor reading high from an open circuit
    • Level sensor stuck at full

    Checks

    1. 1Compare the live level with the real tank level
    2. 2Check the level wiring for an open circuit
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • JCB P203F-68DEF tank level low

    The DEF level is below the warning limit.· Other
    Check soon

    Causes

    • DEF tank genuinely running low
    • DEF level sensor reading low in error
    • Fluid not topped up after the earlier low warning
    • Leak from the tank, line or pump module
    • Sensor connector fault giving a false low level

    Checks

    1. 1Look at the DEF tank and add the correct DEF to the filler neck
    2. 2Compare the live level reading with the fluid in the tank
    3. 3Check the tank, lines and pump module for leaks and wet marks
    4. 4Check the sensor connector for corrosion or crystals
    5. 5Clear the fault after refilling and see if the level reads correctly
    6. 6Check that only clean DEF to the correct standard is used
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JCB P203B-81CAN bus message error from head unit (tank level)

    The DEF head unit sends the tank level over CAN and the message arrives with an error.· Lost message
    Check soon

    Causes

    • Poor CAN connection at the head unit plug
    • Head unit sending corrupted frames

    Checks

    1. 1Check the head unit connector and CAN pins
    2. 2Read the head unit for its own fault codes
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • JCB P203B-86CAN bus error for DEF tank level

    The DEF tank level message on CAN is invalid or out of format, so the receiver rejects the level value.· Lost message
    Check soon

    Causes

    • Head unit and controller software mismatch
    • CAN noise on the head unit link

    Checks

    1. 1Compare the controller and head unit software versions
    2. 2Check the shield and connector on the CAN link
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • JCB P203B-87CAN bus off error from head unit (tank level)

    The DEF head unit went bus-off while reporting tank level, which means it stopped talking on CAN after too many errors, so no level data arrives.· Lost message
    Check soon

    Causes

    • Short or open on the CAN pair to the head unit
    • Head unit failing and driving the bus into error

    Checks

    1. 1Measure CAN high and low at the head unit plug
    2. 2Unplug the head unit and see whether the bus recovers
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • JCB P205B-00DEF tank overheating

    The DEF tank temperature is above the allowed limit, so the fluid or the tank sensor may be overheated.· Real condition
    Check soon

    Causes

    • DEF tank heated by a hot machine or by a stuck-on heater
    • Tank temperature sensor reading high

    Checks

    1. 1Check the DEF temperature with a thermometer and compare it with the live value
    2. 2Check the tank heater switching and the coolant supply to it
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • JCB P205B-06DEF tank temperature increase error

    The DEF tank temperature is rising faster than the heater or the surroundings can explain, so the increase is flagged as an error.· Lost message
    Check soon

    Causes

    • Tank heater stuck on
    • Sensor reading jumping

    Checks

    1. 1Watch the tank temperature on live data while the heater is off
    2. 2Check the heater control and its relay
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • JCB P205B-16DEF tank temperature signal below minimum

    The DEF tank temperature signal is below its minimum.· Shorted low
    Check soon

    Causes

    • Temperature signal wire shorted to ground
    • Sensor shorted

    Checks

    1. 1Compare the live value with the real tank temperature
    2. 2Check the sensor wire for a short to ground
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • JCB P205C-16DEF tank temperature signal voltage below minimum limit

    The DEF tank temperature signal voltage is below its minimum limit, a short toward ground in the sensor circuit.· Other
    Check soon

    Causes

    • Signal wire shorted to ground
    • Sensor shorted internally

    Checks

    1. 1Unplug the sensor and see whether the voltage rises
    2. 2Inspect the head unit connector
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JCB P205B-17DEF tank head unit temperature signal above maximum limit

    The DEF head unit temperature signal is above its maximum limit, so the tank looks far hotter than possible, from an open circuit or a sensor fault.· Open circuit
    Check soon

    Causes

    • Temperature sensor open circuit
    • Sensor reading high

    Checks

    1. 1Compare the live value with the real tank temperature
    2. 2Check continuity of the sensor wire
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • JCB P205D-17DEF tank temperature signal voltage above maximum limit

    The DEF tank temperature signal voltage is above its maximum limit, an open circuit or a short to supply in the sensor circuit.· Shorted high
    Check soon

    Causes

    • Sensor wire open
    • Signal wire shorted to supply

    Checks

    1. 1Check the continuity of the sensor wires
    2. 2Inspect the plug for a pushed-back pin
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • JCB P205B-23DEF tank temperature sensor plausibility below minimum

    The DEF tank temperature sensor reads plausibly low: the value is under what the surrounding temperatures allow.· Erratic or implausible
    Check soon

    Causes

    • Sensor drifted low
    • Sensor fitted loosely or reading air

    Checks

    1. 1Compare the DEF temperature with the coolant and ambient temperatures
    2. 2Check that the sensor is seated in the head unit
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • JCB P205B-24DEF tank temperature sensor plausibility above maximum

    The DEF tank temperature sensor reads plausibly high: the value is above what the surrounding temperatures allow.· Erratic or implausible
    Check soon

    Causes

    • Sensor drifted high
    • Heater overheating the sensor

    Checks

    1. 1Compare the DEF temperature with the ambient temperature after a cold soak
    2. 2Check the heater control
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

  • JCB P205E-81DEF tank temperature signal error on CAN

    The DEF tank temperature signal on CAN has an error: the frame arrives but fails its validity check.· Lost message
    Check soon

    Causes

    • Poor CAN connection
    • Head unit sending corrupted frames

    Checks

    1. 1Check the head unit connector and CAN pins
    2. 2Read the head unit for faults
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • JCB P205E-87CAN bus message error for DEF tank temperature from head unit

    A CAN message error for the DEF tank temperature from the head unit: the message is missing or corrupted, so the controller loses the temperature.· Lost message
    Check soon

    Causes

    • CAN wiring open or loose to the head unit
    • Head unit not powered

    Checks

    1. 1Check the head unit supply and earth
    2. 2Check CAN continuity to the head unit
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • JCB P2043-81CAN bus message error from head unit (DEF temperature)

    The DEF head unit sends the tank temperature over CAN and the message arrives with an error.· Lost message
    Check soon

    Causes

    • Poor CAN connection at the head unit
    • Head unit sending corrupted frames

    Checks

    1. 1Check the connector and CAN pins at the head unit
    2. 2Read the head unit for its own fault codes
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • JCB P2043-86DEF temperature message error from head unit

    The DEF temperature message from the head unit is invalid or out of format, so the receiver rejects the value.· Lost message
    Check soon

    Causes

    • Software mismatch between head unit and controller
    • CAN noise

    Checks

    1. 1Compare software versions
    2. 2Check the CAN shield and connector
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • JCB P2043-87CAN bus off error from head unit (DEF temperature)

    The DEF head unit went bus-off while reporting tank temperature, so no temperature data arrives.· Lost message
    Check soon

    Causes

    • Short or open on the CAN pair to the head unit
    • Head unit failing

    Checks

    1. 1Measure CAN high and low at the head unit
    2. 2Unplug the head unit and see whether the bus recovers
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

  • JCB P3411-87Critically low DEF level detected

    The system has detected a critically low DEF level, so the tank is nearly empty, which starts the first warning toward inducement.· Other
    Check soon

    Causes

    • Tank nearly empty
    • Level sensor reading too low

    Checks

    1. 1Check the real DEF level, refill with approved DEF and watch whether the level rises
    2. 2If the tank is full, check the level sensor and its wiring
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • JCB P3412-87DEF tank sensor open circuit

    The DEF tank level sensor circuit is open: there is no current path, so the controller cannot read the tank level at all.· Open circuit
    Check soon

    Causes

    • Level sensor wire broken or unplugged
    • Level sensor failed open

    Checks

    1. 1Check the continuity of the sensor wires from the head unit plug to the controller
    2. 2Inspect the plug for corrosion
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

  • JCB P3413-87DEF tank sensor short circuit

    The DEF tank level sensor circuit is shorted.· Short circuit
    Check soon

    Causes

    • Level sensor wire shorted to ground or supply
    • Level sensor shorted internally

    Checks

    1. 1Unplug the sensor and check the wires for a short
    2. 2Measure the sensor resistance against the manual value
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the part and the controller. Measure from the output wire to ground and to battery positive, then across the part.

    Good: Open circuit (OL) to ground and to supply; the part reads its listed resistance, not near 0 Ω.

Shared checks

Checks, in order

  1. 1Check the DEF level in the tank against the cluster reading
  2. 2Measure the DEF tank temperature sensor resistance and compare it with the manual curve
  3. 3Check the head unit connector for water and corrosion
  4. 4Inspect the DEF tank head unit connector for water and corrosion
  5. 5Compare the level signal on live data with the real level
  6. 6Check the real DEF tank temperature with a thermometer and compare it with the live value
  7. 7Check the CAN wiring for the head unit messages

Causes

  • DEF tank low or empty
  • Sensor failed
  • Level sensor or head unit failed
  • Wiring or connector fault

Most common here: lost message (9 of 27)

Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

When to stop

You'll notice: A DEF warning shows on the cluster, and power may be reduced if the tank stays low or empty.

Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.