Deutz · High-pressure fuel system
Deutz Fault Code SPN 157 FMI 3
Engine - Rail pressure sensor - Voltage above normal or shorted to high source
What does Deutz code SPN 157 FMI 3 mean?
The EMR4 reads the rail pressure sensor (screwed into the high-pressure common rail) signal above its valid 0.5 to 4.5 V window. Urgency: stop now - shut down and fix before working on. Check first: key on: measure the 5 V reference at the rail pressure sensor plug between supply and ground; 5 V present means the supply side is fine.
- FMI 3
- Voltage above normal or shorted high
Can I keep running with it?
Stop now
Shut down and fix before working on. Running on risks damage or the machine locks out.
What should I check first?
Key on: measure the 5 V reference at the rail pressure sensor plug between supply and ground; 5 V present means the supply side is fine
Then 3 more checksWhere to read it
Read the active and stored faults with Deutz SerDia (or the machine maker's diagnostic tool) on the engine diagnostic plug.
Checks
0 of 4 done
Causes
- Open ground return wire, which pushes the signal up to the reference
- Signal wire touching 5 V or battery in the harness
- Sensor on the common rail leaking or damaged after fuel system work
How it failed
You'll notice: Expect a warning lamp; rail pressure control is lost: the engine usually starts hard or not at all, runs in limp mode or stops, because the EMR4 cannot close the control loop with the fuel metering unit.
Shorted highRead from FMI 3: voltage above normal or shorted high
The signal sits at or near the supply voltage - more than a working sensor can send.
- Meter test
- Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
- Good result
- Open circuit (OL) between them. Any low reading is the short.
When to stop
Common-rail fuel runs at very high pressure. Never open a high-pressure line or fitting with the engine running or just after it stops - a fine fuel jet can pierce skin.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Common rail: metering unit, pre-feed pump, relief valve and rail pressure
2 other codes on this part are also shorted high (SPN 523615 FMI 3, SPN 523906 FMI 3). When they show together, start at the wiring and connector they share.
- SPN 157 FMI 3Engine - Rail pressure sensor - Voltage above normal or shorted to high sourceShorted highStop now
- SPN 157 FMI 4Engine - Rail pressure sensor - Voltage below normal or shorted to low sourceShorted lowStop now
- SPN 164 FMI 2Engine - Rail pressure - Data erratic intermittent or incorrectErratic or implausibleCheck soon
- SPN 523009 FMI 9Engine - Fuel pressure relief valve - Abnormal update rate timeoutLost messageCheck soon
- SPN 523009 FMI 10Engine - Fuel pressure relief valve - Abnormal rate of changeErratic or implausibleCheck soon
- SPN 523470 FMI 2Engine - Fuel pressure relief valve - Data erratic intermittent or incorrectErratic or implausibleStop now
- SPN 523470 FMI 7Engine - Fuel pressure relief valve - Mechanical system not responding or out of adjustmentPart or controllerStop now
- SPN 523470 FMI 11Engine - Fuel pressure relief valve - Root cause not knownOtherStop now
- SPN 523470 FMI 12Engine - Fuel pressure relief valve - Bad intelligent device or componentPart or controllerStop now
Show the other 13 codesHide the other codes
- SPN 523470 FMI 13Engine - Fuel pressure relief valve - Out of calibrationPart or controllerStop now
- SPN 523470 FMI 14Engine - Fuel pressure relief valve - Special instructionsOtherStop now
- SPN 523613 FMI 0Engine - Fuel pressure - Data above normal operational range (Most severe level)Real conditionStop now
- SPN 523613 FMI 1Engine - Fuel pressure - Data below normal operational range (Most severe level)Real conditionStop now
- SPN 523613 FMI 2Engine - Fuel pressure - Data erratic intermittent or incorrectErratic or implausibleCheck soon
- SPN 523615 FMI 3Engine - Fuel metering unit - Voltage above normal or shorted to high sourceShorted highStop now
- SPN 523615 FMI 4Engine - Fuel metering unit - Voltage below normal or shorted to low sourceShorted lowStop now
- SPN 523615 FMI 5Engine - Fuel metering unit - Current below normal or open circuitOpen circuitStop now
- SPN 523615 FMI 12Engine - Fuel metering unit - Bad intelligent device or componentPart or controllerStop now
- SPN 523906 FMI 3Engine - Fuel pre feed pump - Voltage above normal or shorted to high sourceShorted highCheck soon
- SPN 523906 FMI 4Engine - Fuel pre feed pump - Voltage below normal or shorted to low sourceShorted lowCheck soon
- SPN 523906 FMI 5Engine - Fuel pre feed pump - Current below normal or open circuitOpen circuitCheck soon
- SPN 523906 FMI 12Engine - Fuel pre feed pump - Bad intelligent device or componentPart or controllerCheck soon
Related on Equipments Finder
Source
DEUTZ KWP-Codes EMR4 (KWPList EMR4 DE EN, Revision 2.0), page 16
This source lists SPN 157 FMI 3 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Deutz engines with the EMR4 controller (the Deutz list applies to all EMR4 engine series, e.g. TCD 2.9, 3.6, 4.1, 6.1, 7.8 as fitted in machines).
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
