Deutz · Coolant, oil and fuel sensors
Deutz Coolant, oil and low-pressure fuel sensors fault codes
The fluid sensors on the engine. Coolant temperature (SPN 110) and coolant level (SPN 111), oil temperature (SPN 175) and oil pressure (SPN 100), a transmission oil sensor wired in from the machine (SPN 523618), the low-pressure fuel circuit (SPN 94) and the water in fuel sensor (SPN 97).
More about these partsLess
The EMR4 uses them for protection and derating. Each code names the sensor and how its reading failed.
Where to read it
Read the active and stored faults with Deutz SerDia (or the machine maker's diagnostic tool) on the engine diagnostic plug.
What do these codes mean?
Deutz codes SPN 94 FMI 1 to SPN 524132 FMI 2 are all about the coolant, oil and low-pressure fuel sensors. The most common failure type is real condition (9 of 24); 5 need an immediate stop. Start with this check: compare the SerDia reading with an independent one: infrared thermometer for temperatures, a mechanical gauge for oil pressure.
How urgent are they?
5 of 24 codes here mean stop now; the other 19 can wait until the shift ends, but find the cause before the next one.
- Stop now5
- Check soon19
What should I check first?
Compare the SerDia reading with an independent one: infrared thermometer for temperatures, a mechanical gauge for oil pressure
Shared checks24 of 24
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
Engine - Fuel low pressure sensor3 codes
Deutz SPN 94 FMI 1Engine - Fuel low pressure sensor: Reading too low· most severe
The low-pressure fuel sensor (in the low-pressure supply line between the fuel filter and the high-pressure pump) reports a value below the allowed range. This is a plausibility limit, so the low value may be genuine rather than a wiring fault. Deutz list: KWP code 474, blink code 216.· Real conditionReal conditionCheck soonCauses
- Low-pressure fuel sensor drifting low or reading with an offset
- Fuel feed hose collapsing on the suction side
- A blocked pre-filter, empty tank, failing feed pump or an air leak on the suction side drops the feed pressure
Checks
- 1Look at the fuel feed line for air bubbles in a clear section or at a bleed point while cranking
- 2Inspect the sensor port, hose and seal for leaks
- 3Change or check the fuel filters and prime the system; a restricted filter is the most common real cause of low feed pressure
- 4Check the real value with a mechanical gauge before replacing the low-pressure fuel sensor
- 5Compare with its neighbouring sensors in SerDia to see whether only this value is off
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Source wording:Engine - Fuel low pressure sensor - Data below normal operational range (Most severe level)
Full page for SPN 94 FMI 1Deutz SPN 94 FMI 3Engine - Fuel low pressure sensor: Voltage high / shorted high
The EMR4 reads the low-pressure fuel sensor (in the low-pressure supply line between the fuel filter and the high-pressure pump) signal above its valid 0.5 to 4.5 V window. That points to an open sensor ground, a short to supply on the signal wire, or a failed sensor. Deutz list: KWP code 472, blink code 216.· Shorted highShorted highCheck soonCauses
- Open ground return wire, which pushes the signal up to the reference
- Low-pressure fuel sensor failed high
- Plugged fuel filter or air in the line distorting the real pressure
- Signal wire touching 5 V or battery in the harness
Checks
- 1With the sensor unplugged, measure the signal pin; battery voltage there means a short to supply
- 2Compare the low-pressure fuel sensor reading in SerDia with key on and engine off against the value you expect at rest
- 3Key on: measure the 5 V reference at the low-pressure fuel sensor plug between supply and ground; 5 V present means the supply side is fine
- 4Check continuity of the sensor ground wire back to the EMR4 pin
- 5Fit a known good low-pressure fuel sensor temporarily, if you have one, and see whether the reading moves back into range
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Source wording:Engine - Fuel low pressure sensor - Voltage above normal or shorted to high source
Deutz SPN 94 FMI 4Engine - Fuel low pressure sensor: Voltage low / shorted low
The EMR4 reads the low-pressure fuel sensor (in the low-pressure supply line between the fuel filter and the high-pressure pump) signal below its valid 0.5 to 4.5 V window. That points to a shorted signal wire, a lost 5 V reference, or a failed sensor. Deutz list: KWP code 473, blink code 216.· Shorted lowShorted lowCheck soonCauses
- 5 V reference lost: open supply wire or a short on the shared 5 V line
- Low-pressure fuel sensor failed low
- Signal wire rubbed through to ground
Checks
- 1Unplug other sensors sharing the 5 V line one at a time to see whether the reference comes back
- 2With the sensor unplugged, measure resistance from the signal pin to ground; it should not be near zero
- 3Fit a known good low-pressure fuel sensor temporarily, if you have one, and see whether the reading moves back into range
- 4Key on: measure the 5 V reference at the low-pressure fuel sensor plug; no reference means open supply wire or another sensor on that line pulling it down
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Source wording:Engine - Fuel low pressure sensor - Voltage below normal or shorted to low source
Engine - Water in fuel sensor3 codes
Deutz SPN 97 FMI 3Engine - Water in fuel sensor: Voltage high / shorted high
The EMR4 reads the water in fuel sensor (in the fuel pre-filter or water separator bowl) signal above its valid range. The probe circuit is open or pulled up to supply. Deutz list: KWP code 464, blink code 228.· Shorted highShorted highCheck soonCauses
- Open wire or unplugged sensor in the fuel pre-filter
- Probe corroded or failed open
- Sensor probe corroded or coated with sludge
- Water standing in the separator bowl
Checks
- 1Unplug the sensor and check the connector for fuel and corrosion
- 2Inspect the sensor probe at the bottom of the pre-filter for dirt coating
- 3Continuity check from the sensor plug back to the EMR4
- 4Drain the water separator and see whether the code clears; real water is the first thing to rule out
- 5Measure the signal pin with the key on; battery voltage there means a short to supply
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Source wording:Engine - Water in fuel sensor - Voltage above normal or shorted to high source
Full page for SPN 97 FMI 3Deutz SPN 97 FMI 4Engine - Water in fuel sensor: Voltage low / shorted low
The EMR4 reads the water in fuel sensor (in the fuel pre-filter or water separator bowl) signal below its valid range. The probe circuit is shorted to ground, sometimes by real water bridging the probe. Deutz list: KWP code 465, blink code 228.· Shorted lowShorted lowCheck soonCauses
- Signal wire shorted to ground
- Sensor probe corroded or coated with sludge
- Water standing in the separator bowl
Checks
- 1Unplug the sensor; if the code goes away the sensor is the shorted part
- 2Measure resistance from the signal pin to ground with the EMR4 unplugged
- 3Drain the separator and see whether the code clears
- 4Inspect the sensor probe at the bottom of the pre-filter for dirt coating
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Source wording:Engine - Water in fuel sensor - Voltage below normal or shorted to low source
Deutz SPN 97 FMI 12Engine - Water in fuel sensor: Bad device or component
The EMR4 judges the water in fuel sensor (in the fuel pre-filter or water separator bowl) to be a bad device. The probe or its electronics have failed. Deutz list: KWP code 1157, blink code 228.· Part or controllerPart or controllerCheck soonCauses
- Probe failed internally
- Corrosion on the probe
Checks
- 1Drain the water separator bowl and inspect the probe for sludge, corrosion or real water
- 2Fit a known good water in fuel sensor and see whether the code clears for good before ordering the ECU
- 3Check the harness and connector between the water in fuel sensor and the EMR4 for chafing and corrosion
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Check power and ground at the module connector with the key on, then its fuses.
Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
Source wording:Engine - Water in fuel sensor - Bad intelligent device or component
Engine - Oil pressure sensor4 codes
Deutz SPN 100 FMI 0Engine - Oil pressure sensor: Reading too high· most severe
The oil pressure sensor (on the engine block or oil filter housing in the main oil gallery) reports a value above the allowed range. This is a plausibility limit, so the high value may be genuine rather than a wiring fault. Deutz list: KWP code 734, blink code 231.· Real conditionReal conditionStop nowCauses
- Cold thick oil, a stuck oil pressure relief valve or a blocked oil circuit can produce a genuine high reading
- Hose or port feeding the sensor blocked with dirt
- Oil pressure sensor drifting high or reading with an offset
Checks
- 1Check the engine oil level and grade first, because low or diluted oil gives genuine low-pressure codes
- 2Compare the SerDia oil pressure with a mechanical test gauge fitted in the sensor port; only a mechanical gauge tells you if the engine really has pressure
- 3Check the real value against a mechanical gauge or second reading before touching the oil pressure sensor
- 4Inspect the sensor port or hose for restriction
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Source wording:Engine - Oil pressure sensor - Data above normal operational range (Most severe level)
Deutz SPN 100 FMI 1Engine - Oil pressure sensor: Reading too low· most severe
The oil pressure sensor (on the engine block or oil filter housing in the main oil gallery) reports a value below the allowed range. This is a plausibility limit, so the low value may be genuine rather than a wiring fault. Deutz list: KWP code 736, blink code 231.· Real conditionReal conditionStop nowCauses
- Hose or port feeding the sensor split or disconnected
- Sensor body cracked or its thread leaking after an oil filter service
- Oil pressure sensor drifting low or reading with an offset
Checks
- 1Compare with its neighbouring sensors in SerDia to see whether only this value is off
- 2Check the real value with a mechanical gauge before replacing the oil pressure sensor
- 3Compare the SerDia oil pressure with a mechanical test gauge fitted in the sensor port; only a mechanical gauge tells you if the engine really has pressure
- 4Check the engine oil level and grade first, because low or diluted oil gives genuine low-pressure codes
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Source wording:Engine - Oil pressure sensor - Data below normal operational range (Most severe level)
Full page for SPN 100 FMI 1Deutz SPN 100 FMI 3Engine - Oil pressure sensor: Voltage high / shorted high
The EMR4 reads the oil pressure sensor (on the engine block or oil filter housing in the main oil gallery) signal above its valid 0.5 to 4.5 V window. That points to an open sensor ground, a short to supply on the signal wire, or a failed sensor. Deutz list: KWP code 732, blink code 224.· Shorted highShorted highStop nowCauses
- Oil seeping up the sensor thread and wicking into the connector
- Oil pressure sensor failed high
- Open ground return wire, which pushes the signal up to the reference
Checks
- 1Compare the oil pressure sensor reading in SerDia with key on and engine off against the value you expect at rest
- 2With the sensor unplugged, measure the signal pin; battery voltage there means a short to supply
- 3Key on: measure the 5 V reference at the oil pressure sensor plug between supply and ground; 5 V present means the supply side is fine
- 4Check continuity of the sensor ground wire back to the EMR4 pin
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Source wording:Engine - Oil pressure sensor - Voltage above normal or shorted to high source
Deutz SPN 100 FMI 4Engine - Oil pressure sensor: Voltage low / shorted low
The EMR4 reads the oil pressure sensor (on the engine block or oil filter housing in the main oil gallery) signal below its valid 0.5 to 4.5 V window. That points to a shorted signal wire, a lost 5 V reference, or a failed sensor. Deutz list: KWP code 733, blink code 224.· Shorted lowShorted lowStop nowCauses
- 5 V reference lost: open supply wire or a short on the shared 5 V line
- Oil pressure sensor failed low
- Signal wire rubbed through to ground
Checks
- 1Fit a known good oil pressure sensor temporarily, if you have one, and see whether the reading moves back into range
- 2Key on: measure the 5 V reference at the oil pressure sensor plug; no reference means open supply wire or another sensor on that line pulling it down
- 3Compare the oil pressure sensor reading in SerDia with key on and engine off against the value you expect at rest
- 4Unplug other sensors sharing the 5 V line one at a time to see whether the reference comes back
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Source wording:Engine - Oil pressure sensor - Voltage below normal or shorted to low source
Full page for SPN 100 FMI 4
Engine - Coolant temperature sensor4 codes
Deutz SPN 110 FMI 0Engine - Coolant temperature sensor: Reading too high· most severe
The coolant temperature sensor (in the coolant outlet housing on the cylinder head) reports a temperature above the allowed operating range. This is a plausibility limit rather than a wiring fault, so the high reading may well be real. Deutz list: KWP code 92, blink code 225.· Real conditionReal conditionStop nowCauses
- Sensor loosened or damaged when the thermostat housing was last serviced
- Real overheating is possible: low coolant, a blocked radiator core, a slipping fan drive or a thermostat that will not open
- Sensor drifting low in resistance with age
Checks
- 1Check the connector pins for moisture and corrosion, which can pull a reading hot
- 2Check the real temperature with an infrared thermometer or mechanical gauge before touching the coolant temperature sensor
- 3Look for coolant weeping around the sensor seal, which tells you the connector may be wet inside
- 4Look in SerDia at the coolant temperature sensor reading next to a neighbouring temperature; a lone hot value points at the sensor
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Source wording:Engine - Coolant temperature sensor - Data above normal operational range (Most severe level)
Full page for SPN 110 FMI 0Deutz SPN 110 FMI 1Engine - Coolant temperature sensor: Reading too low· most severe
The coolant temperature sensor (in the coolant outlet housing on the cylinder head) reports a temperature below the allowed range. This can be a genuine cold condition or a sensor circuit with extra resistance, so verify with a second thermometer. Deutz list: KWP code 93, blink code 225.· Real conditionReal conditionCheck soonCauses
- Sensor drifting high in resistance after heat cycles
- Sensor loosened or damaged when the thermostat housing was last serviced
- High resistance in the coolant temperature sensor connector or a corroded pin making it read cold
Checks
- 1Compare the coolant temperature sensor value in SerDia with a neighbouring temperature; if only this one is cold the circuit is suspect
- 2Look for coolant weeping around the sensor seal, which tells you the connector may be wet inside
- 3Measure the real temperature with a second thermometer once the engine has warmed up
- 4Compare the SerDia live coolant temperature with an infrared thermometer reading on the thermostat housing once the engine is warm
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Source wording:Engine - Coolant temperature sensor - Data below normal operational range (Most severe level)
Deutz SPN 110 FMI 3Engine - Coolant temperature sensor: Voltage high / shorted high
The EMR4 reads the coolant temperature sensor (in the coolant outlet housing on the cylinder head) at a voltage above its valid window. On a two-wire NTC sensor that means the circuit looks open or pulled up to a supply, so the controller has no usable temperature. Deutz list: KWP code 96, blink code 225.· Shorted highShorted highCheck soonCauses
- Open circuit: broken wire, pushed-out pin or an unplugged connector at the coolant temperature sensor
- Signal wire touching a supply voltage somewhere in the harness
- Coolant seeping along the sensor body into the connector
Checks
- 1With the sensor unplugged and key on, check the signal pin for battery voltage, which would mean a short to supply
- 2Unplug the coolant temperature sensor and measure its resistance across the two pins; an NTC that reads open at room temperature is finished
- 3Bridge the two harness pins with a jumper wire with the key on; the code should change to the voltage-below-normal one if the harness is sound
- 4Compare the SerDia live coolant temperature with an infrared thermometer reading on the thermostat housing once the engine is warm
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Source wording:Engine - Coolant temperature sensor - Voltage above normal or shorted to high source
Full page for SPN 110 FMI 3Deutz SPN 110 FMI 4Engine - Coolant temperature sensor: Voltage low / shorted low
The EMR4 reads the coolant temperature sensor (in the coolant outlet housing on the cylinder head) at a voltage below its valid window. On a two-wire NTC sensor that means the signal is being pulled to ground, either by the wiring or by the sensor itself. Deutz list: KWP code 97, blink code 225.· Shorted lowShorted lowCheck soonCauses
- Signal wire rubbed through to the engine block or frame
- Water bridging the pins inside the coolant temperature sensor connector
- Coolant seeping along the sensor body into the connector
- Sensor element shorted internally, so it reads as extremely hot
Checks
- 1With the EMR4 unplugged, measure resistance from the signal pin to ground; anything but open points to a short in the wire
- 2Measure the coolant temperature sensor resistance and compare it with its temperature; a very low value means the element is shorted
- 3Compare the SerDia live coolant temperature with an infrared thermometer reading on the thermostat housing once the engine is warm
- 4Look for coolant weeping around the sensor seal, which tells you the connector may be wet inside
- 5Unplug the coolant temperature sensor with the key on: if the code flips to the voltage-above-normal one, the harness is fine and the sensor is the shorted part
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Source wording:Engine - Coolant temperature sensor - Voltage below normal or shorted to low source
Engine - Coolant level sensor1 code
Deutz SPN 111 FMI 1Engine - Coolant level sensor: Reading too low· most severe
The coolant level sensor (in the coolant expansion tank or radiator top tank) reports a value below the allowed range. This is a plausibility limit, so the low value may be genuine rather than a wiring fault. Deutz list: KWP code 101, blink code 235.· Real conditionReal conditionCheck soonCauses
- Coolant level sensor drifting low or reading with an offset
- Hose or port feeding the sensor split or disconnected
- Level probe fouled or its connector corroded
- Real coolant loss from a leak, hose or radiator
Checks
- 1Check the real value with a mechanical gauge before replacing the coolant level sensor
- 2Compare with its neighbouring sensors in SerDia to see whether only this value is off
- 3Inspect the sensor port, hose and seal for leaks
- 4Check the coolant level by eye with the engine cold before suspecting the sensor
- 5Inspect the level sensor connector and wire for coolant and corrosion
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Source wording:Engine - Coolant level sensor - Data below normal operational range (Most severe level)
Engine - Oil temperature3 codes
Deutz SPN 175 FMI 0Engine - Oil temperature: Reading too high· most severe
The oil temperature sensor (in the lubrication system near the oil filter housing or oil pan) reports a temperature above the allowed operating range. This is a plausibility limit rather than a wiring fault, so the high reading may well be real. Deutz list: KWP code 745, blink code 144.· Real conditionReal conditionCheck soonCauses
- Sensor tip damaged during an oil filter change
- Sensor drifting low in resistance with age
- Partial short or wet connector lowering the oil temperature sensor resistance so it reads hot
Checks
- 1Look in SerDia at the oil temperature sensor reading next to a neighbouring temperature; a lone hot value points at the sensor
- 2Check the connector pins for moisture and corrosion, which can pull a reading hot
- 3Check the connector for engine oil inside the housing, a common finding where a seal has aged
- 4Read the SerDia oil temperature after a warm-up and see whether it follows coolant temperature in a believable way
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Source wording:Engine - Oil temperature - Data above normal operational range (Most severe level)
Deutz SPN 175 FMI 3Engine - Oil temperature: Voltage high / shorted high
The EMR4 reads the oil temperature sensor (in the lubrication system near the oil filter housing or oil pan) at a voltage above its valid window. On a two-wire NTC sensor that means the circuit looks open or pulled up to a supply, so the controller has no usable temperature. Deutz list: KWP code 743, blink code 144.· Shorted highShorted highCheck soonCauses
- Open circuit: broken wire, pushed-out pin or an unplugged connector at the oil temperature sensor
- Sensor element failed open, so its resistance stays very high at any temperature
- Oil film or oil mist soaking the connector and swelling the seal
Checks
- 1With the sensor unplugged and key on, check the signal pin for battery voltage, which would mean a short to supply
- 2Bridge the two harness pins with a jumper wire with the key on; the code should change to the voltage-below-normal one if the harness is sound
- 3Unplug the oil temperature sensor and measure its resistance across the two pins; an NTC that reads open at room temperature is finished
- 4Check the connector for engine oil inside the housing, a common finding where a seal has aged
- 5Read the SerDia oil temperature after a warm-up and see whether it follows coolant temperature in a believable way
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Source wording:Engine - Oil temperature - Voltage above normal or shorted to high source
Deutz SPN 175 FMI 4Engine - Oil temperature: Voltage low / shorted low
The EMR4 reads the oil temperature sensor (in the lubrication system near the oil filter housing or oil pan) at a voltage below its valid window. On a two-wire NTC sensor that means the signal is being pulled to ground, either by the wiring or by the sensor itself. Deutz list: KWP code 744, blink code 144.· Shorted lowShorted lowCheck soonCauses
- Sensor element shorted internally, so it reads as extremely hot
- Water bridging the pins inside the oil temperature sensor connector
- Oil film or oil mist soaking the connector and swelling the seal
- Signal wire rubbed through to the engine block or frame
Checks
- 1Read the SerDia oil temperature after a warm-up and see whether it follows coolant temperature in a believable way
- 2With the EMR4 unplugged, measure resistance from the signal pin to ground; anything but open points to a short in the wire
- 3Unplug the oil temperature sensor with the key on: if the code flips to the voltage-above-normal one, the harness is fine and the sensor is the shorted part
- 4Check the connector for engine oil inside the housing, a common finding where a seal has aged
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Source wording:Engine - Oil temperature - Voltage below normal or shorted to low source
Machine - Transmission oil sensor2 codes
Deutz SPN 523618 FMI 3Machine - Transmission oil sensor: Voltage high / shorted high
The EMR4 sees the voltage of the transmission oil sensor (on the machine transmission, wired into the engine controller) above normal, or a short to a high source. The controller cannot rely on the signal. Deutz list: KWP code 486, blink code 133.· Shorted highShorted highCheck soonCauses
- Signal wire shorted to battery positive or a supply line
- Open ground or part failed in a way that pulls the signal high
Checks
- 1Unplug the part with the key on and see whether the code changes to the low or open one
- 2With the EMR4 unplugged, measure the wire against battery positive; it should be open
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Source wording:Machine - Transmission oil sensor - Voltage above normal or shorted to high source
Deutz SPN 523618 FMI 4Machine - Transmission oil sensor: Voltage low / shorted low
The EMR4 sees the voltage of the transmission oil sensor (on the machine transmission, wired into the engine controller) below normal, or a short to a low source. The controller cannot rely on the signal. Deutz list: KWP code 487, blink code 133.· Shorted lowShorted lowCheck soonCauses
- Signal wire chafed to ground or the engine block
- Part shorted internally or water in the connector
Checks
- 1Unplug the part with the key on and see whether the code changes to the high or open one
- 2With the EMR4 unplugged, measure the wire to ground; anything near zero ohms means a short
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Source wording:Machine - Transmission oil sensor - Voltage below normal or shorted to low source
Engine - Fuel low pressure pump1 code
Deutz SPN 524057 FMI 2Engine - Fuel low pressure pump: Erratic reading
The EMR4 sees the fuel low pressure pump (in the low-pressure fuel line ahead of the high-pressure pump) signal jump or disagree with other values. The signal is present but unstable, which usually means a loose joint or a failing sensor. Deutz list: KWP code 1505, blink code 843.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Intermittent contact in the connector
- Harness chafed against a bracket in a spot that only touches under vibration
- Fuel low pressure pump on its way out
Checks
- 1Watch the fuel low pressure pump value in SerDia while wiggling the connector and harness
- 2Inspect the connector for loose pins, bent terminals and moisture
- 3Check the 5 V reference for dips while the fault shows
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Source wording:Engine - Fuel low pressure pump - Data erratic intermittent or incorrect
Engine - Fuel low pressure before pump3 codes
Deutz SPN 524132 FMI 0Engine - Fuel low pressure before pump: Reading too high· most severe
The fuel low pressure before pump (in the low-pressure fuel line ahead of the high-pressure pump) reports a value above the allowed range. This is a plausibility limit, so the high value may be genuine rather than a wiring fault. Deutz list: KWP codes 1631 and 1632, blink code 9-5-5.· Real conditionReal conditionCheck soonCauses
- Fuel low pressure before pump drifting high or reading with an offset
- Hose or port feeding the sensor blocked with dirt
Checks
- 1Check the real value against a mechanical gauge or second reading before touching the fuel low pressure before pump
- 2Compare with its neighbouring sensors in SerDia to see whether only this value is off
- 3Inspect the sensor port or hose for restriction
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Source wording:Engine - Fuel low pressure before pump - Data above normal operational range (Most severe level)
Deutz SPN 524132 FMI 1Engine - Fuel low pressure before pump: Reading too low· most severe
The fuel low pressure before pump (in the low-pressure fuel line ahead of the high-pressure pump) reports a value below the allowed range. This is a plausibility limit, so the low value may be genuine rather than a wiring fault. Deutz list: KWP codes 1633 and 1634, blink code 9-5-5.· Real conditionReal conditionCheck soonCauses
- Fuel low pressure before pump drifting low or reading with an offset
- Hose or port feeding the sensor split or disconnected
Checks
- 1Check the real value with a mechanical gauge before replacing the fuel low pressure before pump
- 2Compare with its neighbouring sensors in SerDia to see whether only this value is off
- 3Inspect the sensor port, hose and seal for leaks
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Source wording:Engine - Fuel low pressure before pump - Data below normal operational range (Most severe level)
Deutz SPN 524132 FMI 2Engine - Fuel low pressure before pump: Erratic reading
The EMR4 sees the fuel low pressure before pump (in the low-pressure fuel line ahead of the high-pressure pump) signal jump or disagree with other values. The signal is present but unstable, which usually means a loose joint or a failing sensor. Deutz list: KWP code 1630, blink code 955.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Intermittent contact in the connector
- Harness chafed against a bracket in a spot that only touches under vibration
- Fuel low pressure before pump on its way out
Checks
- 1Watch the fuel low pressure before pump value in SerDia while wiggling the connector and harness
- 2Inspect the connector for loose pins, bent terminals and moisture
- 3Check the 5 V reference for dips while the fault shows
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Source wording:Engine - Fuel low pressure before pump - Data erratic intermittent or incorrect
Shared checks
Checks, in order
- 1Compare the SerDia reading with an independent one: infrared thermometer for temperatures, a mechanical gauge for oil pressure
- 2Check coolant level, oil level and fuel filter condition first, because low or dirty fluid gives genuine codes
- 3Look for fluid inside the sensor connector and weeping at the seal
- 4Drain the fuel water separator and read the water in fuel signal again
- 5Inspect the connector and harness for moisture, bent pins and chafing
Causes
- Fluid seeping along a sensor body into its connector
- Sensor loosened or damaged during service of the thermostat housing, oil filter or fuel filter
- A real condition: overheating, low oil, low coolant, air in the fuel or water in the fuel
- Fault in the sensor, its 5 V supply or its ground wire
Most common here: real condition (9 of 24)
Check the real value with a separate gauge or thermometer before blaming the sensor.
When to stop
You'll notice: A warning lamp or limited function.
Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
