Cummins · Aftertreatment
Cummins Particulate sensor, heater and DPF soot sensor module fault codes
A particulate sensor in the exhaust measures the soot passing the DPF and reports regeneration and detection status to the ECM. It has an internal heater that burns the soot off the sensing element, driven through high-side and low-side drivers from a module that has its own power supply.
More about these partsLess
A fault in the sensor, its supply or its heater stops the ECM from checking the filter. A soot sensor module monitors particulates downstream of the DPF to detect a failed or leaking filter.
Where to read it
Connect INSITE or another J1939-capable scan tool to the 9-pin diagnostic port.
What do these codes mean?
Cummins codes 4143 to 6735 are all about the particulate sensor, heater and DPF soot sensor module. The most common failure type is shorted low (9 of 30); none needs an immediate stop. Start with this check: check the module battery supply and ground at its connector under load.
How urgent are they?
None of the 30 codes here means stop now; all 30 can wait until the shift ends, but find the cause before the next one.
- Check soon30
What should I check first?
Check the module battery supply and ground at its connector under load
Shared checks30 of 30
Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet
Particulate sensor circuit2 codes
Cummins 4143Particulate sensor circuit: Voltage high / shorted high
Same failure as 6643 on the particulate sensor circuit: the same fault condition as 6643, reported for this part. The particulate sensor measures soot downstream of the DPF to detect a leaking or failed filter.· Shorted highShorted highCheck soonCauses
- Same causes as 6643, applied to the particulate sensor circuit
- Wiring or connector problem local to the particulate sensor circuit
Checks
- 1Check the sensor tip for contamination and the DPF for damage.
- 2Work through the checks listed for 6643, starting at the particulate sensor circuit and its connector
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Source wording:Particulate sensor circuit - voltage high (shorted to a high source)
Cummins 4144Particulate sensor circuit: Voltage low / shorted low
Same failure as 6642 on the particulate sensor circuit: the same fault condition as 6642, reported for this part. The particulate sensor measures soot downstream of the DPF to detect a leaking or failed filter.· Shorted lowShorted lowCheck soonCauses
- Same causes as 6642, applied to the particulate sensor circuit
- Wiring or connector problem local to the particulate sensor circuit
Checks
- 1Check the sensor tip for contamination and the DPF for damage.
- 2Work through the checks listed for 6642, starting at the particulate sensor circuit and its connector
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Source wording:Particulate sensor circuit - voltage low (shorted to a low source)
Particulate sensor heater high side driver circuit2 codes
Cummins 4153Particulate sensor heater high side driver circuit: Voltage high / shorted high
Same failure as 6643 on the particulate sensor heater high side driver circuit: the same fault condition as 6643, reported for this part. The high-side driver switches battery voltage to the sensor heater.· Shorted highShorted highCheck soonCauses
- Same causes as 6643, applied to the particulate sensor heater high side driver circuit
- Wiring or connector problem local to the particulate sensor heater high side driver circuit
Checks
- 1Check the heater supply wire and fuse on the high-side circuit.
- 2Work through the checks listed for 6643, starting at the particulate sensor heater high side driver circuit and its connector
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Source wording:Particulate sensor heater high side driver circuit - voltage high (shorted to a high source)
Cummins 5792Particulate sensor heater high side driver circuit: Voltage low / shorted low
Same failure as 6642 on the particulate sensor heater high side driver circuit: the same fault condition as 6642, reported for this part. The high-side driver switches battery voltage to the sensor heater.· Shorted lowShorted lowCheck soonCauses
- Same causes as 6642, applied to the particulate sensor heater high side driver circuit
- Wiring or connector problem local to the particulate sensor heater high side driver circuit
Checks
- 1Check the heater supply wire and fuse on the high-side circuit.
- 2Work through the checks listed for 6642, starting at the particulate sensor heater high side driver circuit and its connector
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Source wording:Particulate sensor heater high side driver circuit - voltage low (shorted to a low source)
Particulate sensor heater low side driver circuit2 codes
Cummins 4154Particulate sensor heater low side driver circuit: Voltage low / shorted low
Same failure as 6642 on the particulate sensor heater low side driver circuit: the same fault condition as 6642, reported for this part. The low-side driver completes the heater circuit to ground.· Shorted lowShorted lowCheck soonCauses
- Same causes as 6642, applied to the particulate sensor heater low side driver circuit
- Wiring or connector problem local to the particulate sensor heater low side driver circuit
Checks
- 1Check the heater ground wire and its connection on the low-side circuit.
- 2Work through the checks listed for 6642, starting at the particulate sensor heater low side driver circuit and its connector
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Source wording:Particulate sensor heater low side driver circuit - voltage low (shorted to a low source)
Cummins 5793Particulate sensor heater low side driver circuit: Voltage high / shorted high
Same failure as 6643 on the particulate sensor heater low side driver circuit: the same fault condition as 6643, reported for this part. The low-side driver completes the heater circuit to ground.· Shorted highShorted highCheck soonCauses
- Same causes as 6643, applied to the particulate sensor heater low side driver circuit
- Wiring or connector problem local to the particulate sensor heater low side driver circuit
Checks
- 1Check the heater ground wire and its connection on the low-side circuit.
- 2Work through the checks listed for 6643, starting at the particulate sensor heater low side driver circuit and its connector
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Source wording:Particulate sensor heater low side driver circuit - voltage high (shorted to a high source)
Particulate sensor regeneration status2 codes
Cummins 4449Particulate sensor regeneration status: Above normal· moderately severe
Same failure as 6721 on the particulate sensor regeneration status: the same fault condition as 6721, reported for this part. The regeneration status shows whether the sensor has finished burning off its soot and is ready to measure.· Real conditionReal conditionCheck soonCauses
- Same causes as 6721, applied to the particulate sensor regeneration status
- Wiring or connector problem local to the particulate sensor regeneration status
Checks
- 1Watch the regeneration status during a heater cycle and confirm it completes.
- 2Work through the checks listed for 6721, starting at the particulate sensor regeneration status and its connector
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Source wording:Particulate sensor regeneration status - above normal - moderately severe
Cummins 5584Particulate sensor regeneration status: Mechanical fault or not responding
The ECM commands the particulate sensor regeneration status but sees no matching response, so it reports a mechanical fault or a part that is not responding even though the wiring may be fine. The regeneration status shows whether the sensor has finished burning off its soot and is ready to measure.· Part or controllerPart or controllerCheck soonCauses
- Particulate sensor regeneration status stuck, seized or restricted by dirt, soot or wear
- Electrical supply too weak to move the part
- Mechanical linkage or return spring broken
Checks
- 1Command the particulate sensor regeneration status with the service tool and watch or listen for it to move
- 2Remove the particulate sensor regeneration status and inspect it for sticking, wear, carbon or debris
- 3Check supply voltage and ground at the particulate sensor regeneration status while it is commanded
- 4Watch the regeneration status during a heater cycle and confirm it completes.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Check power and ground at the module connector with the key on, then its fuses.
Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
Particulate sensor power supply3 codes
Cummins 5577Particulate sensor power supply: Voltage high / shorted high
Same failure as 6643 on the particulate sensor power supply: the same fault condition as 6643, reported for this part. The sensor module takes its power from the battery supply, so a supply fault shows up here before the sensor itself.· Shorted highShorted highCheck soonCauses
- Same causes as 6643, applied to the particulate sensor power supply
- Wiring or connector problem local to the particulate sensor power supply
Checks
- 1Check the sensor module battery feed, fuse and ground under load.
- 2Work through the checks listed for 6643, starting at the particulate sensor power supply and its connector
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Source wording:Particulate sensor power supply - voltage high (shorted to a high source)
Cummins 5578Particulate sensor power supply: Voltage low / shorted low
Same failure as 6642 on the particulate sensor power supply: the same fault condition as 6642, reported for this part. The sensor module takes its power from the battery supply, so a supply fault shows up here before the sensor itself.· Shorted lowShorted lowCheck soonCauses
- Same causes as 6642, applied to the particulate sensor power supply
- Wiring or connector problem local to the particulate sensor power supply
Checks
- 1Check the sensor module battery feed, fuse and ground under load.
- 2Work through the checks listed for 6642, starting at the particulate sensor power supply and its connector
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Source wording:Particulate sensor power supply - voltage low (shorted to a low source)
Cummins 5579Particulate sensor power supply: Above normal· moderately severe
Same failure as 6721 on the particulate sensor power supply: the same fault condition as 6721, reported for this part. The sensor module takes its power from the battery supply, so a supply fault shows up here before the sensor itself.· Real conditionReal conditionCheck soonCauses
- Same causes as 6721, applied to the particulate sensor power supply
- Wiring or connector problem local to the particulate sensor power supply
Checks
- 1Check the sensor module battery feed, fuse and ground under load.
- 2Work through the checks listed for 6721, starting at the particulate sensor power supply and its connector
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Source wording:Particulate sensor power supply - above normal - moderately severe
Particulate sensor heater power supply1 code
Cummins 5581Particulate sensor heater power supply: Erratic reading
Same failure as 6646 on the particulate sensor heater power supply: the same fault condition as 6646, reported for this part. The heater has its own power supply, which the ECM monitors separately.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Same causes as 6646, applied to the particulate sensor heater power supply
- Wiring or connector problem local to the particulate sensor heater power supply
Checks
- 1Check the heater power supply voltage with the heater commanded on.
- 2Work through the checks listed for 6646, starting at the particulate sensor heater power supply and its connector
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Source wording:Particulate sensor heater power supply - data erratic or incorrect
Particulate sensor module battery voltage supply1 code
Cummins 5582Particulate sensor module battery voltage supply: Erratic reading
Same failure as 6646 on the particulate sensor module battery voltage supply: the same fault condition as 6646, reported for this part. The sensor module takes its power from the battery supply, so a supply fault shows up here before the sensor itself.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Same causes as 6646, applied to the particulate sensor module battery voltage supply
- Wiring or connector problem local to the particulate sensor module battery voltage supply
Checks
- 1Check the sensor module battery feed, fuse and ground under load.
- 2Work through the checks listed for 6646, starting at the particulate sensor module battery voltage supply and its connector
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Source wording:Particulate sensor module battery voltage supply - data erratic or incorrect
Particulate sensor detection status1 code
Cummins 5583Particulate sensor detection status: Abnormal rate of change
The particulate sensor detection status changed faster than it physically could, so the ECM treats the reading as a sensor or wiring problem and not as a real change. The detection status tells the ECM whether the sensor is currently able to detect soot.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Intermittent contact in the harness or connector of the particulate sensor detection status
- Failing part giving unstable output
- Poor ground or noisy supply feeding the circuit
Checks
- 1Log the particulate sensor detection status while moving the harness and connector, and look for steps instead of smooth changes
- 2Inspect the particulate sensor detection status connector for water, corrosion and loose pins
- 3Check the supply and ground at the particulate sensor detection status while the engine runs
- 4Watch the detection status live and see whether it settles after the heater cycle.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Particulate sensor2 codes
Cummins 5837Particulate sensor: Reading drifted low
The particulate sensor reads lower than the ECM calculates it should, and it has crept downward over time. That is typical of a sensor that is ageing or leaking. The particulate sensor measures soot downstream of the DPF to detect a leaking or failed filter.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Sensing element ageing and reading low
- Sensor port blocked or leaking so it does not see the true value
- Slow rise in resistance in a connector or wire
Checks
- 1Compare the particulate sensor with a known good sensor or a reference gauge at the same operating point
- 2Inspect the particulate sensor sensing port and seals for blockage or leakage
- 3Measure the voltage drop in the wiring to the particulate sensor for extra resistance
- 4Check the sensor tip for contamination and the DPF for damage.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Source wording:Particulate sensor - data drifted low
Cummins 6688Particulate sensor: Abnormal update rate
The ECM is not receiving fresh data for the particulate sensor at the expected rate. The message is late or missing on the data link, or the sending module has stopped updating it. The particulate sensor measures soot downstream of the DPF to detect a leaking or failed filter.· Lost messageLost messageCheck soonCauses
- Data link wiring fault or a poor connector contact
- The module that sends the message for the particulate sensor is offline or failing
- Power or ground problem at the sending module
Checks
- 1Look for other modules reporting timeouts to find where the link is broken
- 2Check the data link wiring, connectors and both terminators near the particulate sensor source
- 3Read the module that sends the particulate sensor for its own codes and for power or ground faults
- 4Check the sensor tip for contamination and the DPF for damage.
Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end. Meter test
Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
DPF 1 soot sensor ECU internal temperature 1 circuit2 codes
Cummins 6642DPF 1 soot sensor ECU internal temperature 1 circuit: Voltage low / shorted low
The ECM reads the DPF 1 soot sensor ECU internal temperature 1 circuit below its allowed voltage band. That points to a short to ground, an open supply or signal wire, or a failed part, not necessarily a real low value. The soot sensor module has temperature sensors inside its own electronics, which protect it from heat.· Shorted lowShorted lowCheck soonCauses
- Signal wire to the DPF 1 soot sensor ECU internal temperature 1 circuit rubbed through and shorted to ground or to the engine block
- Open 5 V reference or open signal wire that lets the input drop to zero
- Corroded or backed-out pin in the DPF 1 soot sensor ECU internal temperature 1 circuit connector
Checks
- 1Key on, unplug the DPF 1 soot sensor ECU internal temperature 1 circuit and read its circuit at the harness: a reading near zero with the part removed means the wiring is shorted to ground or open
- 2Jumper the 5 V reference to the signal wire at the harness and see whether the code changes to a high-voltage code, which proves the wiring and the ECM input
- 3Measure resistance from the DPF 1 soot sensor ECU internal temperature 1 circuit signal wire to ground with the ECM unplugged to find a short
- 4Check the module mounting position and its distance from the exhaust heat.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Source wording:DPF 1 soot sensor ECU internal temperature 1 circuit - voltage low (shorted to a low source)
Cummins 6643DPF 1 soot sensor ECU internal temperature 1 circuit: Voltage high / shorted high
The ECM reads the DPF 1 soot sensor ECU internal temperature 1 circuit above its allowed voltage band. That points to a short to a 5 V or battery wire, a lost return, or a failed part, rather than a real change in what it measures. The soot sensor module has temperature sensors inside its own electronics, which protect it from heat.· Shorted highShorted highCheck soonCauses
- Short to a 5 V reference or a battery wire in the harness to the DPF 1 soot sensor ECU internal temperature 1 circuit
- Open or high-resistance return wire that lets the signal float high
- Water or corrosion in the connector bridging two pins together
Checks
- 1Key on, unplug the DPF 1 soot sensor ECU internal temperature 1 circuit and read its circuit at the harness: a high reading with the part removed means the wiring is shorted high or the return is lost
- 2Jumper the signal wire of the DPF 1 soot sensor ECU internal temperature 1 circuit to ground at the harness and see whether the code changes to a low-voltage code, which proves the wiring and the ECM input
- 3Check continuity and resistance of the return wire from the DPF 1 soot sensor ECU internal temperature 1 circuit back to the ECM
- 4Check the module mounting position and its distance from the exhaust heat.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Source wording:DPF 1 soot sensor ECU internal temperature 1 circuit - voltage high (shorted to a high source)
DPF 1 soot sensor ECU internal temperature 2 circuit2 codes
Cummins 6644DPF 1 soot sensor ECU internal temperature 2 circuit: Voltage low / shorted low
Same failure as 6642 on the DPF 1 soot sensor ECU internal temperature 2 circuit: the same fault condition as 6642, reported for this part. The soot sensor module has temperature sensors inside its own electronics, which protect it from heat.· Shorted lowShorted lowCheck soonCauses
- Same causes as 6642, applied to the DPF 1 soot sensor ECU internal temperature 2 circuit
- Wiring or connector problem local to the DPF 1 soot sensor ECU internal temperature 2 circuit
Checks
- 1Check the module mounting position and its distance from the exhaust heat.
- 2Work through the checks listed for 6642, starting at the DPF 1 soot sensor ECU internal temperature 2 circuit and its connector
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Source wording:DPF 1 soot sensor ECU internal temperature 2 circuit - voltage low (shorted to a low source)
Cummins 6645DPF 1 soot sensor ECU internal temperature 2 circuit: Voltage high / shorted high
Same failure as 6643 on the DPF 1 soot sensor ECU internal temperature 2 circuit: the same fault condition as 6643, reported for this part. The soot sensor module has temperature sensors inside its own electronics, which protect it from heat.· Shorted highShorted highCheck soonCauses
- Same causes as 6643, applied to the DPF 1 soot sensor ECU internal temperature 2 circuit
- Wiring or connector problem local to the DPF 1 soot sensor ECU internal temperature 2 circuit
Checks
- 1Check the module mounting position and its distance from the exhaust heat.
- 2Work through the checks listed for 6643, starting at the DPF 1 soot sensor ECU internal temperature 2 circuit and its connector
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Source wording:DPF 1 soot sensor ECU internal temperature 2 circuit - voltage high (shorted to a high source)
DPF 1 soot sensor ECU internal temperature3 codes
Cummins 6646DPF 1 soot sensor ECU internal temperature: Erratic reading
The ECM judges the DPF 1 soot sensor ECU internal temperature to be erratic or implausible: the value jumps, drifts or disagrees with related readings, which suggests a poor connection or a part on its way out. The soot sensor module has temperature sensors inside its own electronics, which protect it from heat.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Intermittent connector or wiring contact on the DPF 1 soot sensor ECU internal temperature
- Part ageing or failing and giving unstable output
- Electrical noise from a poorly routed wire or a bad ground
Checks
- 1Watch the DPF 1 soot sensor ECU internal temperature live in INSITE and wiggle the harness and connector to catch dropouts
- 2Compare the DPF 1 soot sensor ECU internal temperature with a related reading to decide which one is wrong
- 3Check the connector for moisture and corrosion and the ground connection for tightness
- 4Check the module mounting position and its distance from the exhaust heat.
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Source wording:DPF 1 soot sensor ECU internal temperature - data erratic or incorrect
Cummins 6721DPF 1 soot sensor ECU internal temperature: Above normal· moderately severe
The DPF 1 soot sensor ECU internal temperature is above its normal range (severity: moderately severe). The ECM sets the code from a real reading, so look for a genuine cause before blaming the sensor. The soot sensor module has temperature sensors inside its own electronics, which protect it from heat.· Real conditionReal conditionCheck soonCauses
- A real over-limit condition in the system the DPF 1 soot sensor ECU internal temperature measures
- Sensor or circuit reading high from a wiring fault
- A cooling, flow or restriction problem upstream that drives the value up
Checks
- 1Confirm the real condition with a gauge or a second reading before replacing the DPF 1 soot sensor ECU internal temperature
- 2Check that the DPF 1 soot sensor ECU internal temperature circuit codes are not active, since a wiring fault can fake a high reading
- 3Look for the physical cause upstream, such as restriction, leakage, poor cooling or heavy load
- 4Check the module mounting position and its distance from the exhaust heat.
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Source wording:DPF 1 soot sensor ECU internal temperature - above normal - moderately severe
Cummins 6735DPF 1 soot sensor ECU internal temperature: Above normal· moderately severe
Same failure as 6721 on the DPF 1 soot sensor ECU internal temperature: the same fault condition as 6721, reported for this part. The soot sensor module has temperature sensors inside its own electronics, which protect it from heat.· Real conditionReal conditionCheck soonCauses
- Same causes as 6721, applied to the DPF 1 soot sensor ECU internal temperature
- Wiring or connector problem local to the DPF 1 soot sensor ECU internal temperature
Checks
- 1Check the module mounting position and its distance from the exhaust heat.
- 2Work through the checks listed for 6721, starting at the DPF 1 soot sensor ECU internal temperature and its connector
The reading against the band the controller allows. Meter test
Check the real value with a separate gauge or thermometer before blaming the sensor.
Good: If the gauge agrees with the display, fix the machine, not the sensor.
Source wording:DPF 1 soot sensor ECU internal temperature - above normal - moderately severe
DPF soot temperature sensor3 codes
Cummins 6647DPF soot temperature sensor: Voltage high / shorted high
Same failure as 6643 on the DPF soot temperature sensor: the same fault condition as 6643, reported for this part. The soot temperature sensor is a separate temperature sensor used by the soot sensor module.· Shorted highShorted highCheck soonCauses
- Same causes as 6643, applied to the DPF soot temperature sensor
- Wiring or connector problem local to the DPF soot temperature sensor
Checks
- 1Check the sensor harness at the soot sensor module for damage and corrosion.
- 2Work through the checks listed for 6643, starting at the DPF soot temperature sensor and its connector
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Source wording:DPF soot temperature sensor - voltage high (shorted to a high source)
Cummins 6648DPF soot temperature sensor: Voltage low / shorted low
Same failure as 6642 on the DPF soot temperature sensor: the same fault condition as 6642, reported for this part. The soot temperature sensor is a separate temperature sensor used by the soot sensor module.· Shorted lowShorted lowCheck soonCauses
- Same causes as 6642, applied to the DPF soot temperature sensor
- Wiring or connector problem local to the DPF soot temperature sensor
Checks
- 1Check the sensor harness at the soot sensor module for damage and corrosion.
- 2Work through the checks listed for 6642, starting at the DPF soot temperature sensor and its connector
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Source wording:DPF soot temperature sensor - voltage low (shorted to a low source)
Cummins 6649DPF soot temperature sensor: Erratic reading
Same failure as 6646 on the DPF soot temperature sensor: the same fault condition as 6646, reported for this part. The soot temperature sensor is a separate temperature sensor used by the soot sensor module.· Erratic or implausibleErratic or implausibleCheck soonCauses
- Same causes as 6646, applied to the DPF soot temperature sensor
- Wiring or connector problem local to the DPF soot temperature sensor
Checks
- 1Check the sensor harness at the soot sensor module for damage and corrosion.
- 2Work through the checks listed for 6646, starting at the DPF soot temperature sensor and its connector
The reading against the band the controller allows. Meter test
Watch the live value on the service tool while you flex the harness and tap the connector.
Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.
Source wording:DPF soot temperature sensor - data erratic or incorrect
DPF soot sensor module3 codes
Cummins 6651DPF soot sensor module: Voltage high / shorted high
Same failure as 6643 on the DPF soot sensor module: the same fault condition as 6643, reported for this part. The soot sensor module is the electronics that read the soot sensor and send the results to the ECM.· Shorted highShorted highCheck soonCauses
- Same causes as 6643, applied to the DPF soot sensor module
- Wiring or connector problem local to the DPF soot sensor module
Checks
- 1Check the module supply, ground and data link connections.
- 2Work through the checks listed for 6643, starting at the DPF soot sensor module and its connector
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.
Good: Open circuit (OL) between them. Any low reading is the short.
Source wording:DPF soot sensor module - voltage high (shorted to a high source)
Cummins 6652DPF soot sensor module: Voltage low / shorted low
Same failure as 6642 on the DPF soot sensor module: the same fault condition as 6642, reported for this part. The soot sensor module is the electronics that read the soot sensor and send the results to the ECM.· Shorted lowShorted lowCheck soonCauses
- Same causes as 6642, applied to the DPF soot sensor module
- Wiring or connector problem local to the DPF soot sensor module
Checks
- 1Check the module supply, ground and data link connections.
- 2Work through the checks listed for 6642, starting at the DPF soot sensor module and its connector
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Source wording:DPF soot sensor module - voltage low (shorted to a low source)
Cummins 6653DPF soot sensor module: Current high / grounded
The ECM sees too much current, or a shorted path to ground, in the DPF soot sensor module. The circuit is overloaded or the part inside has failed short. The soot sensor module is the electronics that read the soot sensor and send the results to the ECM.· Shorted lowShorted lowCheck soonCauses
- Wire to the DPF soot sensor module shorted to ground
- Failed part drawing excessive current
- Water or corrosion inside the connector
Checks
- 1Unplug the DPF soot sensor module and see whether the high-current code goes away, which separates a failed part from a wiring short
- 2Measure the resistance from each wire of the DPF soot sensor module circuit to ground with the ECM unplugged
- 3Inspect the connector and harness for pinch points and water entry
- 4Check the module supply, ground and data link connections.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
Source wording:DPF soot sensor module - current high or grounded circuit
DPF soot sensor module voltage converter1 code
Cummins 6722DPF soot sensor module voltage converter: Bad device or component
The ECM flags the DPF soot sensor module voltage converter as a bad device or component after a self-test or a response check failed. The part itself is the most likely cause. The module has an internal voltage converter that makes the supply for the soot sensing electronics.· Part or controllerPart or controllerCheck soonCauses
- Failed DPF soot sensor module voltage converter or its internal electronics
- Supply or ground fault that made the self-test fail
- Connector or harness damage that stops the part from communicating
Checks
- 1Check supply voltage and ground at the DPF soot sensor module voltage converter before replacing it
- 2Inspect the DPF soot sensor module voltage converter connector and wiring for water, corrosion and damage
- 3Read the DPF soot sensor module voltage converter for any stored status or self-test result with the service tool
- 4Check the supply voltage at the module and replace the module only if the supply is good.
Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins. Meter test
Check power and ground at the module connector with the key on, then its fuses.
Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
Shared checks
Checks, in order
- 1Check the module battery supply and ground at its connector under load
- 2Check the module connector and its power and ground
- 3Unplug the sensor and check the heater driver circuits for opens, shorts to ground and shorts to supply
- 4Compare the module temperature readings with the ambient temperature
- 5Inspect the connector and the harness near the exhaust for burn marks and corrosion
- 6Inspect the module mounting and heat shielding
- 7Read the detection and regeneration status live and see whether it changes as the sensor warms
Causes
- Connector or harness fault between the sensor module and the ECM
- Sensor module wiring damaged
- Failed sensing element or heater
- Module internal temperature too high
Most common here: shorted low (9 of 30)
Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
When to stop
You'll notice: A lamp and a logged code, an inhibited soot check and in some cases a derate; the engine itself runs normally.
Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.
Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Related on Equipments Finder
Sources
- Cummins ISX15 (2013-2018) Fault Codes List (Diesel Repair)
- Cummins L9 (2016-2020) Fault Code List (Diesel Repair)
- Cummins L9 (2024-2025) Fault Code List (Diesel Repair)
Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
