EF Logo

Cummins · Aftertreatment

Cummins DEF pump, DEF controller and line heater relay fault codes

The DEF pump builds pressure for the dosing unit. On some engines a separate DEF controller manages the dosing unit and communicates with the ECM over the data link.

More about these parts

A relay switches power to the DEF line heaters on command from the ECM.

FaultCheck1688Cummins · DEF controller
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Connect INSITE or another J1939-capable scan tool to the 9-pin diagnostic port.

What do these codes mean?

Cummins codes 1688 to 7381 are all about the dEF pump, DEF controller and line heater relay. The most common failure type is erratic or implausible (4 of 18); none needs an immediate stop. Start with this check: check the pump connector and wiring for corrosion.

How urgent are they?

None of the 18 codes here means stop now; 16 can wait until the shift ends, but find the cause before the next one; 2 are information only.

  • Check soon16
  • Info2

What should I check first?

Check the pump connector and wiring for corrosion

Shared checks

18 of 18

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • DEF controller6 codes

    • Cummins 1688DEF controller: Bad device or component

      The ECM judges the DEF controller to be an internal failure of the device or module.· Part or controller
      Check soon

      Causes

      • Internal failure of the device
      • Supply or ground problem causing it to reset
      • Corrupt software

      Checks

      1. 1Check supply and ground at the device before condemning it
      2. 2Reflash with the correct software where possible
      3. 3Replace the device if the fault persists after the supply tests are good
      ControllerPartSupplySignalGround?
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Check power and ground at the module connector with the key on, then its fuses.

      Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

    • Cummins 3557DEF controller: Erratic reading

      The ECM judges the DEF controller to be erratic, intermittent or implausible.· Erratic or implausible
      Check soon

      Causes

      • Intermittent connector or wiring contact
      • Sensor ageing or failing
      • A real fluctuation in the system it measures

      Checks

      1. 1Watch the DEF controller live and wiggle the harness and connector to catch dropouts
      2. 2Compare it with a related sensor to see which one is wrong
      3. 3Check the connector for moisture and corrosion
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Watch the live value on the service tool while you flex the harness and tap the connector.

      Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

      Source wording:DEF controller - data erratic or incorrect

    • Cummins 3597DEF controller: Abnormal update rate

      The ECM is not receiving fresh data for the DEF controller at the expected rate.· Lost message
      Check soon

      Causes

      • Data link wiring fault or a poor connector contact
      • The module that sends the message is offline or failing
      • Power or ground problem at the sending module

      Checks

      1. 1Look for other modules reporting timeouts to find where the link is broken
      2. 2Check the data link wiring, connectors and terminators
      3. 3Read the sending module for its own codes
      Module AModule BCAN HCAN L120 Ω120 Ω
      Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

      Meter test

      Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

      Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

    • Cummins 3598DEF controller: Network data in error

      The ECM received the DEF controller over the data link but the message is flagged as invalid, so it cannot be used.· Lost message
      Check soon

      Causes

      • Sending module reporting an invalid value
      • Data link wiring or connector fault

      Checks

      1. 1Find which module sends the message and read its codes
      2. 2Check the data link wiring and connectors
      Module AModule BCAN HCAN L120 Ω120 Ω
      Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

      Meter test

      Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

      Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

      Source wording:DEF controller - network data received in error

    • Cummins 3736DEF controller: Root cause not known

      The ECM detects a problem with the DEF controller but cannot tie it to one specific cause.· Other
      Info

      Causes

      • A related fault that set first
      • An intermittent connection or supply problem

      Checks

      1. 1Read all active and inactive codes and work the others first
      2. 2Check the supply, ground and connectors of the circuit involved
      3. 3Read the freeze-frame data for the conditions when it set
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Read the code with the service tool and note which other codes are active with it.

      Good: Codes that appear together usually share one cause - start with the wiring they share.

    • Cummins 4431DEF controller: Out of calibration

      The ECM reports the DEF controller as out of calibration, so its value does not agree with the stored calibration or with the other data it is compared against.· Part or controller
      Check soon

      Causes

      • Sensor or device out of tolerance
      • Wrong calibration or learn data after a repair

      Checks

      1. 1Check whether a learn or calibration procedure is needed after the last repair
      2. 2Compare with a related sensor and replace the part if the offset is real
      ControllerPartSupplySignalGround?
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Check power and ground at the module connector with the key on, then its fuses.

      Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

  • DEF line heater relay4 codes

    • Cummins 3562DEF line heater relay: Voltage high / shorted high

      The ECM sees the DEF line heater relay drive circuit with voltage above the expected level.· Shorted high
      Check soon

      Causes

      • Output wire shorted to battery or a switched power feed
      • Open ground or return path on the component
      • Component winding failed or its connector damaged

      Checks

      1. 1Unplug the DEF line heater relay connector, key on, and measure the output pin to ground; battery voltage with nothing connected points to a short to power
      2. 2Inspect the harness for a rubbed wire or damaged splice touching a power feed
      3. 3Measure the component resistance across its pins to rule out an open winding
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

      Good: Open circuit (OL) between them. Any low reading is the short.

      Source wording:DEF line heater relay - voltage high (shorted to a high source)

    • Cummins 3563DEF line heater relay: Voltage low / shorted low

      The ECM sees the DEF line heater relay drive circuit with voltage below the expected level.· Shorted low
      Check soon

      Causes

      • Output wire shorted to ground or chafed through to the chassis
      • Component winding shorted internally
      • Connector corroded and bridging the pins

      Checks

      1. 1Unplug the DEF line heater relay connector and measure the output pin to ground; a short here means the harness is at fault
      2. 2Measure the component resistance across its pins; a very low reading means a shorted winding
      3. 3Inspect the connector for moisture and bridged terminals
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

      Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

      Source wording:DEF line heater relay - voltage low (shorted to a low source)

    • Cummins 3564DEF line heater relay: Current low / open circuit

      The ECM commands the DEF line heater relay but sees little or no current flow.· Open circuit
      Check soon

      Causes

      • Open wire or a terminal pushed back in the connector
      • Open winding in the component
      • Blown fuse or failed relay feeding the circuit

      Checks

      1. 1Check continuity from the ECM pin to the DEF line heater relay connector, wiggling the harness as you test
      2. 2Measure the component resistance with the connector unplugged; an open reading means the part has failed
      3. 3Check the fuse and relay feeding the circuit
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

      Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

      Source wording:DEF line heater relay - current low or open circuit

    • Cummins 3713DEF line heater relay: Mechanical fault or not responding

      The ECM commands the DEF line heater relay but it does not respond as expected, or its movement is out of adjustment.· Part or controller
      Check soon

      Causes

      • Mechanism seized, sooted or blocked
      • Wear or incorrect adjustment of the linkage or part
      • Supply or return fault limiting its movement

      Checks

      1. 1Command the DEF line heater relay in INSITE and watch whether it moves and returns
      2. 2Inspect the part and its linkage for sticking, debris or wear
      3. 3Check supply and return connections before replacing it
      ControllerPartSupplySignalGround?
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Check power and ground at the module connector with the key on, then its fuses.

      Good: Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.

  • DEF controller temperature1 code

    • Cummins 3648DEF controller temperature: Above normal· moderately severe

      The DEF controller temperature is above its normal operating range and the ECM rates it as moderately severe.· Real condition
      Check soon

      Causes

      • The monitored condition really is too high because of the system it measures
      • A related fault that set first and is pushing the reading out of range

      Checks

      1. 1Compare the live DEF controller temperature with a second reading or gauge to see whether the condition is real
      2. 2Read the freeze-frame for speed, load and temperature when the code set
      3. 3Clear any other active codes first and retest under load
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Check the real value with a separate gauge or thermometer before blaming the sensor.

      Good: If the gauge agrees with the display, fix the machine, not the sensor.

      Source wording:DEF controller temperature - above normal - moderately severe

  • DEF pump 1 motor speed2 codes

    • Cummins 4276DEF pump 1 motor speed: Erratic reading

      The ECM judges the DEF pump 1 motor speed to be erratic, intermittent or implausible.· Erratic or implausible
      Check soon

      Causes

      • Intermittent connector or wiring contact
      • Sensor ageing or failing
      • A real fluctuation in the system it measures

      Checks

      1. 1Watch the DEF pump 1 motor speed live and wiggle the harness and connector to catch dropouts
      2. 2Compare it with a related sensor to see which one is wrong
      3. 3Check the connector for moisture and corrosion
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Watch the live value on the service tool while you flex the harness and tap the connector.

      Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

      Source wording:DEF pump 1 motor speed - data erratic or incorrect

    • Cummins 7381DEF pump 1 motor speed: Reading drifted high

      The DEF pump 1 motor speed reading has drifted high compared with what the ECM expects from the other sensors and its model.· Erratic or implausible
      Check soon

      Causes

      • Sensor element contaminated or aged
      • Real condition such as an exhaust leak or restriction biasing the reading

      Checks

      1. 1Compare the DEF pump 1 motor speed with the related sensors on a cold, soaked engine, where they should agree
      2. 2Replace the sensor only after the wiring and any leaks have been ruled out
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Watch the live value on the service tool while you flex the harness and tap the connector.

      Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

      Source wording:DEF pump 1 motor speed - data drifted high

  • DEF pump 1 motor speed circuit1 code

    • Cummins 5626DEF pump 1 motor speed circuit: Current low / open circuit

      The ECM commands the DEF pump 1 motor speed circuit but sees little or no current flow.· Open circuit
      Check soon

      Causes

      • Open wire or a terminal pushed back in the connector
      • Open winding in the component
      • Blown fuse or failed relay feeding the circuit

      Checks

      1. 1Check continuity from the ECM pin to the DEF pump 1 motor speed circuit connector, wiggling the harness as you test
      2. 2Measure the component resistance with the connector unplugged; an open reading means the part has failed
      3. 3Check the fuse and relay feeding the circuit
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

      Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

      Source wording:DEF pump 1 motor speed circuit - current low or open circuit

  • DEF pump command circuit2 codes

    • Cummins 5864DEF pump command circuit: Voltage high / shorted high

      The ECM sees the DEF pump command circuit drive circuit with voltage above the expected level.· Shorted high
      Check soon

      Causes

      • Output wire shorted to battery or a switched power feed
      • Open ground or return path on the component
      • Component winding failed or its connector damaged

      Checks

      1. 1Unplug the DEF pump command circuit connector, key on, and measure the output pin to ground; battery voltage with nothing connected points to a short to power
      2. 2Inspect the harness for a rubbed wire or damaged splice touching a power feed
      3. 3Measure the component resistance across its pins to rule out an open winding
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

      Good: Open circuit (OL) between them. Any low reading is the short.

      Source wording:DEF pump command circuit - voltage high (shorted to a high source)

    • Cummins 5865DEF pump command circuit: Voltage low / shorted low

      The ECM sees the DEF pump command circuit drive circuit with voltage below the expected level.· Shorted low
      Check soon

      Causes

      • Output wire shorted to ground or chafed through to the chassis
      • Component winding shorted internally
      • Connector corroded and bridging the pins

      Checks

      1. 1Unplug the DEF pump command circuit connector and measure the output pin to ground; a short here means the harness is at fault
      2. 2Measure the component resistance across its pins; a very low reading means a shorted winding
      3. 3Inspect the connector for moisture and bridged terminals
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

      Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

      Source wording:DEF pump command circuit - voltage low (shorted to a low source)

  • DEF pump drive percentage1 code

    • Cummins 6485DEF pump drive percentage: Erratic reading

      The ECM judges the DEF pump drive percentage to be erratic, intermittent or implausible.· Erratic or implausible
      Check soon

      Causes

      • Intermittent connector or wiring contact
      • Sensor ageing or failing
      • A real fluctuation in the system it measures

      Checks

      1. 1Watch the DEF pump drive percentage live and wiggle the harness and connector to catch dropouts
      2. 2Compare it with a related sensor to see which one is wrong
      3. 3Check the connector for moisture and corrosion
      allowed rangetime
      The reading against the band the controller allows.

      Meter test

      Watch the live value on the service tool while you flex the harness and tap the connector.

      Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

      Source wording:DEF pump drive percentage - data erratic or incorrect

  • DEF pump motor speed1 code

    • Cummins 7325DEF pump motor speed: Condition exists

      The ECM sets this code when it recognises a defined condition for the DEF pump motor speed.· Other
      Info

      Causes

      • A monitor or protection condition that has been met
      • A related fault that set first

      Checks

      1. 1Read the code description and freeze-frame in INSITE for the exact condition
      2. 2Work the related active codes first, then recheck
      ControllerPartSupplySignalGround
      Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

      Meter test

      Read the code with the service tool and note which other codes are active with it.

      Good: Codes that appear together usually share one cause - start with the wiring they share.

Shared checks

Checks, in order

  1. 1Check the pump connector and wiring for corrosion
  2. 2Check the controller power and ground connections
  3. 3Prime the system and listen to the pump while it runs
  4. 4Check the controller temperature and mounting
  5. 5Command the relay in INSITE and listen for it
  6. 6Command the pump in INSITE and watch its speed
  7. 7Reflash or replace the controller after the checks

Causes

  • Pump motor failed
  • Controller power or ground fault
  • Relay failed
  • Wiring or connector fault

Most common here: erratic or implausible (4 of 18)

Watch the live value on the service tool while you flex the harness and tap the connector.

When to stop

You'll notice: DEF dosing is affected, leading to high NOx and an emissions lamp.

Repeated aftertreatment faults lead to an engine derate. Parked regenerations and dosing tests are run with the service tool; do not remove or bypass DPF or SCR parts.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.