EF Logo

Cummins · Cooling

Cummins Coolant temperature, oil temperature and oil pressure fault codes

The coolant temperature sensor reads the engine's coolant temperature and the oil temperature sensor reads the temperature of the lubricating oil. The ECM uses coolant temperature for fuelling, fan control, cold-start strategy and engine protection, and oil temperature to protect the engine and adjust warm-up.

More about these parts

A separate cooling system monitor checks that the engine warms up as expected. The oil pressure sensor reads pressure in the main oil rifle.

FaultCheck141Cummins · Coolant temperature, oil temperature and oil pressure
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Connect INSITE or another J1939-capable scan tool to the 9-pin diagnostic port.

What do these codes mean?

Cummins codes 135 to 3243 are all about the coolant temperature, oil temperature and oil pressure. The most common failure type is shorted high (3 of 20); 3 need an immediate stop. Start with this check: compare the coolant and oil temperature readings at key on, engine off with ambient after the engine has sat overnight.

How urgent are they?

3 of 20 codes here mean stop now; 14 can wait until the shift ends, but find the cause before the next one; 3 are information only.

  • Stop now3
  • Check soon14
  • Info3

What should I check first?

Compare the coolant and oil temperature readings at key on, engine off with ambient after the engine has sat overnight

Shared checks

20 of 20

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Cummins 135Engine oil rifle pressure 1 sensor circuit - Voltage high / shorted high

    The ECM sees the engine oil rifle pressure 1 sensor signal circuit above its normal voltage band.· Shorted high
    Check soon

    Causes

    • Signal wire shorted to the 5 V reference or battery voltage in the harness
    • Open sensor return wire letting the signal float up
    • Sensor failed high or its connector is corroded

    Checks

    1. 1Read the live engine oil rifle pressure 1 sensor circuit value with the key on; a reading pinned at the top of its range confirms the high-voltage fault
    2. 2Unplug the sensor and check reference and return at the harness, since a lost return gives the same symptom
    3. 3With the key off, test the signal wire for continuity to the reference and to battery positive
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

    Source wording:Engine oil rifle pressure 1 sensor circuit - voltage high (shorted to a high source)

  • Cummins 141Engine oil pressure sensor signal voltage low

    The ECM sees the engine oil pressure sensor signal below its normal voltage band.· Shorted low
    Check soon

    Causes

    • Oil pressure sensor signal wire squashed between the filter housing and the block, shorting to ground
    • 5 V reference lost at the sensor connector, giving an all-low signal
    • Sensor failed low even though real pressure is normal
    • Oil soaking into the connector and bridging terminals

    Checks

    1. 1Read oil pressure at key on, engine off; any value above zero with the engine stopped proves a sensor or circuit fault
    2. 2Hook a mechanical gauge to the oil rifle and compare it with the INSITE value while cranking
    3. 3Measure the reference voltage at the unplugged sensor connector
    4. 4Test the signal wire for a short to ground along the harness to the ECM
    5. 5Replace the sensor if the gauge shows good pressure and the harness tests clean
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Cummins 143Engine oil pressure low· moderately severe

    The oil rifle pressure is lower than expected at the current speed.· Other
    Check soon

    Causes

    • Low oil level or wrong oil grade
    • Oil pump wear or a stuck relief valve
    • Oil filter restriction
    • Oil pressure sensor or circuit fault
    • Bearing wear

    Checks

    1. 1Check the oil level and condition on the dipstick with the engine off and level
    2. 2Measure the actual oil pressure with a mechanical gauge
    3. 3Replace the oil and filter if the service interval has passed or the oil is thin and dirty
    4. 4Look for fuel or coolant dilution on the dipstick and check the oil smell and colour
    5. 5Check the sensor circuit if the real pressure is fine
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

    Source wording:Engine oil pressure low - moderately severe

    Full page for 143
  • Cummins 144Engine coolant temperature sensor signal voltage high

    The ECM sees the engine coolant temperature sensor signal as very cold or open.· Shorted high
    Check soon

    Causes

    • Coolant temperature sensor connector unplugged or loose at the thermostat housing
    • Sensor wire broken inside the insulation near the thermostat housing
    • Thermistor inside the sensor failed open
    • Corrosion in the connector raising the circuit resistance

    Checks

    1. 1Cold engine key on: a reading far below ambient or at the lowest end of the scale means the circuit is open
    2. 2Unplug the sensor and bridge the two harness pins with a jumper; the reading should swing hot if the harness is good
    3. 3Check continuity of both wires to the ECM connector with the key off
    4. 4Inspect the terminals for green corrosion and a pin pushed back
    5. 5Replace the sensor if the jumper test works and the sensor will not read
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Cummins 145Engine coolant temperature sensor signal voltage low

    The ECM sees the engine coolant temperature sensor signal as extremely hot or shorted.· Shorted low
    Check soon

    Causes

    • Coolant temperature sensor wire shorted to the thermostat housing or a bracket
    • Coolant wicking up the sensor wires and bridging the terminals
    • Thermistor inside the sensor failed shorted
    • Harness hardened by heat near the thermostat housing and cracked to ground

    Checks

    1. 1Cold engine key on: a coolant reading far above anything a cold engine can reach means the circuit is shorted
    2. 2Unplug the sensor; if the reading swings to cold the sensor was the short, if not the harness is grounded
    3. 3Measure signal to ground at the unplugged harness with the key off
    4. 4Inspect the harness insulation next to the thermostat housing
    5. 5Replace the sensor if it reads shorted on the bench
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Cummins 146Engine coolant temperature high· moderately severe

    The coolant temperature is above the second protection limit.· Other
    Check soon

    Causes

    • Low coolant level or air in the cooling system
    • Radiator or charge-air cooler restricted by dirt
    • Fan clutch or fan drive not engaging fully

    Checks

    1. 1Check the coolant level cold and look around the radiator, hoses and water pump for leaks
    2. 2Clean the radiator and charge-air cooler fins
    3. 3Confirm the fan comes on at the expected temperature
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

    Source wording:Engine coolant temperature high - moderately severe

  • Cummins 151Engine coolant temperature high· most severe

    The engine coolant is above the highest protection limit.· Other
    Stop now

    Causes

    • Low coolant level from a leak
    • Fan not engaging (viscous or electric clutch, fan control circuit)
    • Blocked radiator or charge-air cooler fins, or a collapsed hose

    Checks

    1. 1Stop the engine and let it cool; check the coolant level
    2. 2Inspect hoses, radiator, water pump and the head gasket area for leaks
    3. 3Check the fan turns on when the temperature rises
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

    Source wording:Engine coolant temperature high - most severe

  • Cummins 212Engine oil temperature sensor 1 circuit - Voltage high / shorted high

    The ECM sees the engine oil temperature sensor 1 circuit signal circuit above its normal voltage band.· Shorted high
    Check soon

    Causes

    • Signal wire shorted to the 5 V reference or battery voltage in the harness
    • Open sensor return wire letting the signal float up
    • Sensor failed high or its connector is corroded

    Checks

    1. 1Read the live engine oil temperature sensor 1 circuit value with the key on; a reading pinned at the top of its range confirms the high-voltage fault
    2. 2Unplug the sensor and check reference and return at the harness, since a lost return gives the same symptom
    3. 3With the key off, test the signal wire for continuity to the reference and to battery positive
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

    Source wording:Engine oil temperature sensor 1 circuit - voltage high (shorted to a high source)

  • Cummins 213Engine oil temperature sensor 1 circuit - Voltage low / shorted low

    The ECM sees the engine oil temperature sensor 1 circuit signal circuit below its normal voltage band.· Shorted low
    Check soon

    Causes

    • Signal wire shorted to ground in the harness
    • Open 5 V reference wire so the signal collapses
    • Sensor failed low or its connector is wet or corroded

    Checks

    1. 1Read the live engine oil temperature sensor 1 circuit value with the key on; a reading pinned at the bottom of its range confirms the low-voltage fault
    2. 2Unplug the sensor and check that the 5 V reference arrives at the connector
    3. 3With the key off, test the signal wire for a short to ground
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

    Source wording:Engine oil temperature sensor 1 circuit - voltage low (shorted to a low source)

  • Cummins 214Engine oil temperature too high· most severe

    The oil temperature is above the highest limit, which can break down the oil and damage bearings.· Lost message
    Stop now

    Causes

    • Engine overheating from a cooling system fault
    • Oil cooler plugged or the oil level too low
    • Wrong oil grade or degraded oil

    Checks

    1. 1Stop the engine and check the oil level and the coolant temperature
    2. 2Check the cooling system as for an overheating engine
    3. 3Check the oil cooler for blockage or leakage, and look for oil in the coolant or coolant in the oil
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

    Source wording:Engine oil temperature too high - most severe

  • Cummins 334Coolant temperature - Erratic reading

    The coolant temperature reading is erratic or does not follow the engine's real temperature.· Erratic or implausible
    Check soon

    Causes

    • Coolant sensor in the thermostat housing corroded
    • Air pocket round the sensor from a low coolant level
    • Connector with poor contact

    Checks

    1. 1Compare the INSITE coolant temperature with an infrared reading at the thermostat housing
    2. 2Check the coolant level cold and bleed any air pocket from around the sensor
    3. 3Wiggle the sensor connector while watching the value
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

    Source wording:Coolant temperature - data erratic

  • Cummins 415Engine oil pressure low· most severe

    The oil pressure at the rifle is below the lowest limit.· Lost message
    Stop now

    Causes

    • Low oil level or oil diluted with fuel or coolant
    • Oil pump worn or its pickup blocked
    • Oil filter plugged or the bypass valve stuck
    • Worn bearings
    • Oil pressure sensor or its circuit fault

    Checks

    1. 1Stop the engine and check the oil level and condition
    2. 2Check with a mechanical gauge to confirm real oil pressure
    3. 3Check the oil filter and the pressure relief valve
    4. 4Look for fuel or coolant in the oil on the dipstick, because dilution drops the oil pressure
    5. 5Check the sensor circuit if the gauge pressure is normal
    Module AModule BCAN HCAN L120 Ω120 Ω
    Typical J1939 link: two modules, CAN high and low, a 120 Ω terminator at each end.

    Meter test

    Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.

    Good: About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.

    Source wording:Engine oil pressure low - most severe

    Full page for 415
  • Cummins 421Engine oil temperature - Above normal· moderately severe

    The engine oil temperature is above its normal operating range and the ECM rates it as moderately severe.· Real condition
    Check soon

    Causes

    • The monitored condition really is too high because of the system it measures
    • A related fault that set first and is pushing the reading out of range

    Checks

    1. 1Compare the live engine oil temperature with a second reading or gauge to see whether the condition is real
    2. 2Read the freeze-frame for speed, load and temperature when the code set
    3. 3Clear any other active codes first and retest under load
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

    Source wording:Engine oil temperature - above normal - moderately severe

  • Cummins 425Engine oil temperature - Erratic reading

    The ECM judges the engine oil temperature to be erratic, intermittent or implausible.· Erratic or implausible
    Check soon

    Causes

    • Intermittent connector or wiring contact
    • Sensor ageing or failing
    • A real fluctuation in the system it measures

    Checks

    1. 1Watch the engine oil temperature live and wiggle the harness and connector to catch dropouts
    2. 2Compare it with a related sensor to see which one is wrong
    3. 3Check the connector for moisture and corrosion
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

    Source wording:Engine oil temperature - data erratic or incorrect

  • Cummins 435Oil pressure sensor - Erratic reading

    The oil pressure reading is erratic or does not follow engine speed, so the sensor, its connector or the oil system is behaving oddly.· Erratic or implausible
    Check soon

    Causes

    • Sensor on the oil rifle drifting or sticking
    • Connector with a poor contact on the block side
    • Aerated or thin oil making pressure fluctuate

    Checks

    1. 1Compare the INSITE oil pressure with a mechanical gauge at idle and at rated speed
    2. 2Check the oil level and look at the oil on the dipstick for foam or fuel dilution
    3. 3Wiggle the sensor harness while watching the live value
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Watch the live value on the service tool while you flex the harness and tap the connector.

    Good: A steady value that tracks the real condition. A jump while flexing is the loose pin or wire.

    Source wording:Oil pressure sensor - data erratic

  • Cummins 2646Engine coolant temperature - Condition exists

    The ECM sets this code when it recognises a defined condition for the engine coolant temperature.· Other
    Info

    Causes

    • A monitor or protection condition that has been met
    • A related fault that set first

    Checks

    1. 1Read the code description and freeze-frame in INSITE for the exact condition
    2. 2Work the related active codes first, then recheck
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Cummins 2659Engine coolant temperature - Condition exists

    The ECM sets this code when it recognises a defined condition for the engine coolant temperature.· Other
    Info

    Causes

    • A monitor or protection condition that has been met
    • A related fault that set first

    Checks

    1. 1Read the code description and freeze-frame in INSITE for the exact condition
    2. 2Work the related active codes first, then recheck
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

  • Cummins 2789Engine coolant temperature too low

    The coolant does not reach the normal operating temperature after a normal warm-up time.· Real condition
    Info

    Causes

    • Thermostat stuck open
    • Coolant temperature sensor reading low
    • Winter front or shutters missing in cold weather

    Checks

    1. 1Watch the coolant temperature after a normal drive and compare with an infrared thermometer
    2. 2Check whether the thermostat is stuck open by feeling the lower radiator hose warm up too soon
    3. 3Inspect the coolant temperature sensor connector
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Cummins 2963Engine coolant temperature high· least severe

    The coolant temperature has passed the first, lowest warning limit.· Other
    Check soon

    Causes

    • Dirty radiator or air-conditioning condenser blocking airflow
    • Fan clutch slipping
    • Coolant level slightly low
    • Thermostat slow to open
    • Heavy load in high ambient temperature

    Checks

    1. 1Check the coolant level cold and top up with the correct coolant mixture if it is low
    2. 2Clean the radiator and the air-conditioning condenser fins so air can flow through them
    3. 3Check that the fan engages when the engine warms up, using the INSITE fan test if available
    4. 4Check the thermostat opens and that the upper and lower hoses are not collapsed or soft
    5. 5Compare the temperature when the engine is under load and when idling
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Read the code with the service tool and note which other codes are active with it.

    Good: Codes that appear together usually share one cause - start with the wiring they share.

    Source wording:Engine coolant temperature high - least severe

    Full page for 2963
  • Cummins 3243Engine cooling system monitor - Below normal· moderately severe

    The engine cooling system monitor is below its normal operating range and the ECM rates it as moderately severe.· Real condition
    Check soon

    Causes

    • The monitored condition really is too low because of the system it measures
    • A related fault that set first and is pushing the reading out of range

    Checks

    1. 1Compare the live engine cooling system monitor with a second reading or gauge to see whether the condition is real
    2. 2Read the freeze-frame for speed, load and temperature when the code set
    3. 3Clear any other active codes first and retest under load
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

    Source wording:Engine cooling system monitor - below normal - moderately severe

Shared checks

Checks, in order

  1. 1Compare the coolant and oil temperature readings at key on, engine off with ambient after the engine has sat overnight
  2. 2Check the oil level and condition first, before reading any codes
  3. 3Check coolant level, thermostat opening and fan operation before condemning a sensor
  4. 4Verify the real pressure with a mechanical gauge before replacing the sensor
  5. 5Unplug the sensor and measure resistance at ambient, then compare it with the same type of good sensor
  6. 6Check the sensor connector and wiring for damage and corrosion
  7. 7Inspect the connector and wiring for corrosion, moisture and chafing, and wiggle them while watching the live value

Causes

  • Sensor connector corroded or loose, or harness damaged
  • Low oil level or wrong viscosity oil
  • Failed thermistor reading out of range
  • Oil pump, regulator or bearing wear

Most common here: shorted high (3 of 20)

Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

When to stop

You'll notice: Hard starting or white smoke when cold, fan running constantly, engine warm-up that never ends, or a protective derate or shutdown if the engine really overheats.

Let the engine cool before opening the cooling system; a hot cap releases scalding coolant. Running on with an overheat warning risks a head gasket or seized engine.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.