Cummins · Lubrication - SPN 100 FMI 1
Cummins Fault Code 415
Engine oil pressure low - most severe
What does Cummins code 415 mean?
The oil pressure at the rifle is below the lowest limit. Continuing to run can wreck bearings quickly. Urgency: stop now - shut down and fix before working on. Check first: stop the engine and check the oil level and condition.
Can I keep running with it?
Stop now
Shut down and fix before working on. Running on risks damage or the machine locks out.
What should I check first?
Stop the engine and check the oil level and condition
Then 4 more checksWhere to read it
Connect INSITE or another J1939-capable scan tool to the 9-pin diagnostic port.
Checks
0 of 5 done
Causes
- Low oil level or oil diluted with fuel or coolant
- Oil pump worn or its pickup blocked
- Oil filter plugged or the bypass valve stuck
- Worn bearings
1 more causeFewer causes
- Oil pressure sensor or its circuit fault
How it failed
You'll notice: A red stop lamp and an audible alarm, and the ECM may shut the engine down after a short delay.
Lost messageRead from how the source describes the code
A module stopped hearing another on the data link, or the data came late or garbled.
- Meter test
- Key off. Measure resistance between CAN high and CAN low at the diagnostic connector.
- Good result
- About 60 Ω on a two-terminator J1939 link. About 120 Ω means one terminator or one leg is open.
When to stop
Low oil pressure can wreck bearings in minutes. Stop the engine and check the level before restarting; if the level is right, do not run it again until the pressure is checked with a gauge.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Coolant temperature, oil temperature and oil pressure
1 other code on this part is also lost message (214). When they show together, start at the wiring and connector they share.
- 212Engine oil temperature sensor 1 circuit - voltage high (shorted to a high source)Shorted highCheck soon
- 213Engine oil temperature sensor 1 circuit - voltage low (shorted to a low source)Shorted lowCheck soon
- 214Engine oil temperature too high - most severeLost messageStop now
- 334Coolant temperature - data erraticErratic or implausibleCheck soon
- 415Engine oil pressure low - most severeLost messageStop now
- 421Engine oil temperature - above normal - moderately severeReal conditionCheck soon
- 425Engine oil temperature - data erratic or incorrectErratic or implausibleCheck soon
- 435Oil pressure sensor - data erraticErratic or implausibleCheck soon
- 2646Engine coolant temperature - condition existsOtherInformation
Show the other 11 codesHide the other codes
- 135Engine oil rifle pressure 1 sensor circuit - voltage high (shorted to a high source)Shorted highCheck soon
- 141Engine oil pressure sensor signal voltage lowShorted lowCheck soon
- 143Engine oil pressure low - moderately severeOtherCheck soon
- 144Engine coolant temperature sensor signal voltage highShorted highCheck soon
- 145Engine coolant temperature sensor signal voltage lowShorted lowCheck soon
- 146Engine coolant temperature high - moderately severeOtherCheck soon
- 151Engine coolant temperature high - most severeOtherStop now
- 2659Engine coolant temperature - condition existsOtherInformation
- 2789Engine coolant temperature too lowReal conditionInformation
- 2963Engine coolant temperature high - least severeOtherCheck soon
- 3243Engine cooling system monitor - below normal - moderately severeReal conditionCheck soon
Related on Equipments Finder
Source
Cummins ISX15 (2013-2018) Fault Codes List (Diesel Repair)
This source lists 415 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Cummins ISX15/X15/ISB6.7/B6.7/L9 engines (J1939 SPN 100, FMI 1); same code list used in trucks, buses and machines with these engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
