Cummins · Lubrication - SPN 100 FMI 4
Cummins Fault Code 141
Engine oil pressure sensor signal voltage low
What does Cummins code 141 mean?
The ECM sees the engine oil pressure sensor signal below its normal voltage band. That points to a signal wire shorted to ground, a lost 5 V reference or a sensor that failed low. Urgency: check soon - the machine may derate or limit a function. Check first: read oil pressure at key on, engine off; any value above zero with the engine stopped proves a sensor or circuit fault.
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Read oil pressure at key on, engine off; any value above zero with the engine stopped proves a sensor or circuit fault
Then 4 more checksWhere to read it
Connect INSITE or another J1939-capable scan tool to the 9-pin diagnostic port.
Checks
0 of 5 done
Causes
- Oil pressure sensor signal wire squashed between the filter housing and the block, shorting to ground
- 5 V reference lost at the sensor connector, giving an all-low signal
- Sensor failed low even though real pressure is normal
- Oil soaking into the connector and bridging terminals
How it failed
You'll notice: The oil pressure gauge or warning lamp may act up.
Shorted lowRead from how the source describes the code
The signal sits at or near zero volts - less than a working sensor can send.
- Meter test
- Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
- Good result
- Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
When to stop
Low oil pressure can wreck bearings in minutes. Stop the engine and check the level before restarting; if the level is right, do not run it again until the pressure is checked with a gauge.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Coolant temperature, oil temperature and oil pressure
2 other codes on this part are also shorted low (145, 213). When they show together, start at the wiring and connector they share.
- 135Engine oil rifle pressure 1 sensor circuit - voltage high (shorted to a high source)Shorted highCheck soon
- 141Engine oil pressure sensor signal voltage lowShorted lowCheck soon
- 143Engine oil pressure low - moderately severeOtherCheck soon
- 144Engine coolant temperature sensor signal voltage highShorted highCheck soon
- 145Engine coolant temperature sensor signal voltage lowShorted lowCheck soon
- 146Engine coolant temperature high - moderately severeOtherCheck soon
- 151Engine coolant temperature high - most severeOtherStop now
- 212Engine oil temperature sensor 1 circuit - voltage high (shorted to a high source)Shorted highCheck soon
- 213Engine oil temperature sensor 1 circuit - voltage low (shorted to a low source)Shorted lowCheck soon
Show the other 11 codesHide the other codes
- 214Engine oil temperature too high - most severeLost messageStop now
- 334Coolant temperature - data erraticErratic or implausibleCheck soon
- 415Engine oil pressure low - most severeLost messageStop now
- 421Engine oil temperature - above normal - moderately severeReal conditionCheck soon
- 425Engine oil temperature - data erratic or incorrectErratic or implausibleCheck soon
- 435Oil pressure sensor - data erraticErratic or implausibleCheck soon
- 2646Engine coolant temperature - condition existsOtherInformation
- 2659Engine coolant temperature - condition existsOtherInformation
- 2789Engine coolant temperature too lowReal conditionInformation
- 2963Engine coolant temperature high - least severeOtherCheck soon
- 3243Engine cooling system monitor - below normal - moderately severeReal conditionCheck soon
Related on Equipments Finder
Source
Cummins ISX15 (2013-2018) Fault Codes List (Diesel Repair)
This source lists 141 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Cummins ISX15/X15/L9 engines (J1939 SPN 100, FMI 4); same code list used in trucks, buses and machines with these engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
