Bobcat · Hydraulics
Bobcat Fault Code 05‑15
Hydraulic charge pressure shutdown level
What does Bobcat code 05-15 mean?
The engine was shut down because charge pressure fell too low. The engine will not stay running until the pressure is restored. Urgency: stop now - shut down and fix before working on. Check first: check the oil level and top up with the correct hydraulic fluid; a low tank is the cheapest and most common fix.
Can I keep running with it?
Stop now
Shut down and fix before working on. Running on risks damage or the machine locks out.
What should I check first?
Check the oil level and top up with the correct hydraulic fluid; a low tank is the cheapest and most common fix
Then 3 more checksWhere this code shows
On touchscreen R-series machines, touch the screen and pick Service Codes from the menu.
Checks
0 of 4 done
Causes
- Blocked charge filter
- Pressure transducer failing and reading below the real value
- Low hydraulic oil level
- Charge pump worn out
How it failed
You'll notice: The engine was shut down by the controller because charge pressure fell below the protection level.
Real conditionRead from how the source describes the code
The sensor reading is valid but outside the allowed range - the problem may be real.
- Meter test
- Check the real value with a separate gauge or thermometer before blaming the sensor.
- Good result
- If the gauge agrees with the display, fix the machine, not the sensor.
When to stop
Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Hydraulic charge pressure, workgroup and load sensing pressure
3 other codes on this part are also real condition (05-09, M6221, M6222). When they show together, start at the wiring and connector they share.
- 05-09Hydraulic charge pressure lowReal conditionCheck soon
- 05-14Hydraulic charge pressure extremely lowOtherStop now
- 05-15Hydraulic charge pressure shutdown levelReal conditionStop now
- 05-21Hydraulic charge pressure out of range highOtherCheck soon
- 05-22Hydraulic charge pressure out of range lowOtherCheck soon
- C101D-16Tilt rod pressure sensor out of range lowOtherCheck soon
- C101D-17Tilt rod pressure sensor out of range highOtherCheck soon
- M0509Hydraulic charge pressure lowOtherCheck soon
- M0510Hydraulic charge pressure highOtherCheck soon
Show the other 18 codesHide the other codes
- M0511Hydraulic charge pressure extremely highLost messageCheck soon
- M0514Hydraulic charge pressure extremely lowOtherStop now
- M0515Hydraulic charge pressure shutdownOtherStop now
- M0521Hydraulic charge pressure out of range highOtherCheck soon
- M0522Hydraulic charge pressure out of range lowOtherCheck soon
- C1080-FAHydraulic charge pressure highLost messageCheck soon
- C1080-FBHydraulic charge pressure extremely highOtherStop now
- C1080-F8Hydraulic charge pressure extremely lowOtherStop now
- C1080-F9Low hydraulic pump pressureOtherCheck soon
- C1097-16Hydraulic charge pressure sensor out of range lowOtherCheck soon
- C1097-17Hydraulic charge pressure sensor out of range highOtherCheck soon
- H1421Lift base pressure out of range highOtherCheck soon
- H1422Lift base pressure out of range lowOtherCheck soon
- M2521Load sense sensor out of range highOtherCheck soon
- M2522Load sense sensor out of range lowOtherCheck soon
- M6204Load moment sensor in errorOtherCheck soon
- M6221Overload warning sensor out of range highReal conditionCheck soon
- M6222Overload warning sensor out of range lowReal conditionCheck soon
Other Bobcat codes: Hydraulics
- VSE001-00Oil temp. sensor, signal above normal range
- VSP001-02Front pump press. sensor, incorrect signal
- VSE001-03Oil temp. sensor, voltage above normal
- VSP001-03Front pump press. sensor, voltage above normal
- VSE001-04Oil temp. sensor, voltage below normal
- VSP001-04Front pump press. sensor, voltage below normal
- VPV001-05Pump P/V (a), current below normal
Related on Equipments Finder
Source
Bobcat S205 Operation & Maintenance Manual, service codes list
This source lists 05-15 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Older Bobcat skid-steer and track loaders using the two-digit service codes (S205 manual, similar models).
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
