EF Logo

Volvo/Mack · MID 128 engine ECU - fuel, injectors and timing

Volvo/Mack Water in fuel sensor fault codes

The water in fuel sensor sits in the fuel filter housing and warns when water has collected in the filter bowl.

FaultCheckMID 128PID 97FMI 0Volvo/Mack · Water in fuel sensor
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.

What do these codes mean?

Volvo/Mack codes MID 128 PID 97 FMI 0, MID 128 PID 97 FMI 3 and MID 128 PID 97 FMI 4 are all about the water in fuel sensor. None needs an immediate stop. Start with this check: drain the water from the filter and inspect the fuel.

How urgent are they?

None of the 3 codes here means stop now; all 3 can wait until the shift ends, but find the cause before the next one.

  • Check soon3

What should I check first?

Drain the water from the filter and inspect the fuel

Shared checks

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Volvo/Mack MID 128 PID 97 FMI 0Water in fuel detected

    The water-in-fuel sensor in the fuel filter or water separator reports water.· Real condition
    Check soon

    Causes

    • Water collected in the fuel filter or separator from condensation or a contaminated fill
    • Water separator not drained at the service interval
    • Contaminated fuel from the tank or a supplier

    Checks

    1. 1Drain the water separator and look at what comes out
    2. 2Check the fuel in the tank for water or water layer, especially after heavy rain or a bad fill
    3. 3Replace the fuel filter if it has been saturated
    4. 4Prime the system and recheck the live sensor status before clearing the code
    allowed rangetime
    The reading against the band the controller allows.

    Meter test

    Check the real value with a separate gauge or thermometer before blaming the sensor.

    Good: If the gauge agrees with the display, fix the machine, not the sensor.

  • Volvo/Mack MID 128 PID 97 FMI 3Water in fuel sensor circuit shorted high or open

    The water-in-fuel sensor signal reads high, which the Mack table ties to an open circuit.· Shorted high
    Check soon

    Causes

    • Open circuit in the water-in-fuel sensor wiring
    • Sensor unplugged after a filter change
    • Water-in-fuel sensor failed

    Checks

    1. 1Check the sensor connector at the filter housing is plugged in and the pins are clean
    2. 2Test continuity of both sensor wires between the connector and the ECM
    3. 3Drain the water separator manually as a precaution while you test
    4. 4Replace the water-in-fuel sensor if the harness tests good
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Volvo/Mack MID 128 PID 97 FMI 4Water in fuel sensor circuit shorted to ground

    The water-in-fuel sensor signal is low, which Mack ties to a short to ground, an open circuit or a faulty sensor.· Shorted low
    Check soon

    Causes

    • Short to ground in the sensor wiring
    • Open circuit
    • Faulty water-in-fuel sensor

    Checks

    1. 1Check the sensor connector for fuel soaking and corrosion at the filter housing
    2. 2Test the signal wire for a short to ground with the key off
    3. 3Test continuity of the wires back to the ECM and write down the reading
    4. 4Replace the sensor and drain the water separator once the circuit is clean
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

Shared checks

Checks, in order

  1. 1Drain the water from the filter and inspect the fuel
  2. 2Check the sensor connector and wiring for corrosion, rubbing and pins that no longer grip
  3. 3Check the fuel tank for water or contamination
  4. 4Clear the code and confirm it does not return

Causes

  • Water in the fuel tank or filter
  • Sensor failed or contaminated
  • Open or shorted sensor wiring

When to stop

You'll notice: A water in fuel lamp or message appears and the engine may lose power.

Common-rail fuel runs at very high pressure. Never open a high-pressure line or fitting with the engine running or just after it stops - a fine fuel jet can pierce skin.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.