Volvo/Mack · MID 128 engine ECU - sensors and levels
Volvo/Mack Fault Code MID 128 PSID 109 FMI 12
Coolant thermostat leaking or stuck open
What does Volvo/Mack code MID 128 PSID 109 FMI 12 mean?
The coolant thermostat is leaking or stuck open, so the engine takes too long to warm up and the ECM logs a fault for it. Urgency: check soon - the machine may derate or limit a function. Check first: watch the coolant warm-up time in the scan tool on a cold start and compare it with a known good truck.
- MID 128
- Which control unit reports it
- PSID 109
- Maker component at fault
- FMI 12
- Bad intelligent device or component
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Watch the coolant warm-up time in the scan tool on a cold start and compare it with a known good truck
Then 3 more checksWhere to read it
Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.
Checks
0 of 4 done
Causes
- Thermostat stuck open
- Coolant temperature sensor misreading
- Fan running too much
How it failed
You'll notice: Longer engine warm-up, poor heat in the cab and a lit MIL while the thermostat stays open.
Part or controllerRead from FMI 12: bad intelligent device or component
The controller reports a part, module or its software as faulty or not responding.
- Meter test
- Check power and ground at the module connector with the key on, then its fuses.
- Good result
- Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
When to stop
Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Coolant thermostat monitoring
1 other code on this part is also part or controller (MID 128 PSID 109 FMI 7). When they show together, start at the wiring and connector they share.
- MID 128 PSID 109 FMI 7Coolant thermostat stuck closedPart or controllerCheck soon
- MID 128 PSID 109 FMI 12Coolant thermostat leaking or stuck openPart or controllerCheck soon
Other Volvo/Mack codes: MID 128 engine ECU - sensors and levels
- MID 128 SID 33 FMI 3Fan clutch output shorted high - fan runs full speed
- MID 128 SID 33 FMI 4Fan clutch output shorted low
- MID 128 SID 33 FMI 5Fan clutch output circuit open
- MID 128 PID 98 FMI 1Engine oil level critically low
- MID 128 PID 98 FMI 4Engine oil level sensor shorted to ground
- MID 128 PID 98 FMI 5Engine oil level sensor circuit open
- MID 128 PID 100 FMI 1Engine oil pressure critically low
Related on Equipments Finder
Source
This source lists MID 128 PSID 109 FMI 12 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Mack MP7/MP8/MP10 engines (CHU, CXU, GU, TD) with the 2010-and-later MID 128 engine ECU; the same MID 128 numbers appear on Volvo D11/D13 engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
