Volvo/Mack · MID 128 engine ECU - fuel, injectors and timing
Volvo/Mack Fault Code MID 128 PID 94 FMI 7
Fuel delivery pressure dropping, supply not responding
What does Volvo/Mack code MID 128 PID 94 FMI 7 mean?
Measured fuel supply pressure has fallen and the fuel system is not responding the way the ECM expects. In the Mack table the usual suspects are a clogged filter, a leaking line or fitting and a weak fuel pump. Urgency: check soon - the machine may derate or limit a function. Check first: read fuel pressure live at idle and at full load and note where it drops.
- MID 128
- Which control unit reports it
- PID 94
- Parameter at fault
- FMI 7
- Mechanical system not responding
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Read fuel pressure live at idle and at full load and note where it drops
Then 4 more checksWhere to read it
Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.
Checks
0 of 5 done
Causes
- Clogged fuel filter or water separator
- Leaking fuel line or loose fitting letting air in
- Weak or failing fuel supply pump
- Faulty fuel pressure sensor reading wrongly
How it failed
You'll notice: The engine derates, loses power under load and may stumble when pulling hard because the injectors are not getting enough fuel.
Part or controllerRead from FMI 7: mechanical system not responding
The controller reports a part, module or its software as faulty or not responding.
- Meter test
- Check power and ground at the module connector with the key on, then its fuses.
- Good result
- Battery voltage on power, under 0.2 V drop on ground. Then it needs the service tool.
When to stop
Common-rail fuel runs at very high pressure. Never open a high-pressure line or fitting with the engine running or just after it stops - a fine fuel jet can pierce skin.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Fuel delivery pressure
- MID 128 PID 94 FMI 3Fuel delivery pressure sensor signal highShorted highCheck soon
- MID 128 PID 94 FMI 5Fuel delivery pressure sensor circuit open or lowOpen circuitCheck soon
- MID 128 PID 94 FMI 7Fuel delivery pressure dropping, supply not respondingPart or controllerCheck soon
- MID 128 PID 94 FMI 18Fuel delivery pressure moderately lowReal conditionCheck soon
Other Volvo/Mack codes: MID 128 engine ECU - fuel, injectors and timing
- MID 128 PID 97 FMI 0Water in fuel detected
- MID 128 SID 1 FMI 3Injector cylinder 1 circuit shorted high
- MID 128 SID 1 FMI 5Injector cylinder 1 circuit open or shorted to ground
- MID 128 SID 1 FMI 7Injector cylinder 1 balancing above limit
- MID 128 SID 1 FMI 8Injector cylinder 1 misfire detected
- MID 128 SID 1 FMI 13Injector cylinder 1 out of calibration
- MID 128 SID 2 FMI 5Injector cylinder 2 circuit open or shorted
Related on Equipments Finder
Source
This source lists MID 128 PID 94 FMI 7 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Mack MP7/MP8/MP10 engines (CHU, CXU, GU, TD) with the 2010-and-later MID 128 engine ECU; the same MID 128 numbers appear on Volvo D11/D13 engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
