Volvo/Mack · MID 128 engine ECU - sensors and levels
Volvo/Mack Fault Code MID 128 PID 110 FMI 4
Engine coolant temperature sensor signal low or shorted to ground
What does Volvo/Mack code MID 128 PID 110 FMI 4 mean?
The coolant temperature signal voltage is below the valid range, which the ECM reads as a short to ground at the sensor or in its wiring. The sensor value is replaced with a default. Urgency: check soon - the machine may derate or limit a function. Check first: read the live temperature; an unrealistically cold value on a hot engine confirms the fault.
- MID 128
- Which control unit reports it
- PID 110
- Parameter at fault
- FMI 4
- Voltage below normal or shorted low
Can I keep running with it?
Check soon
The machine may derate or limit a function. Find the cause before the next shift.
What should I check first?
Read the live temperature; an unrealistically cold value on a hot engine confirms the fault
Then 4 more checksWhere to read it
Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.
Checks
0 of 5 done
Causes
- Coolant temperature sensor shorted internally
- Signal wire chafed to ground along the front of the engine
- Water in the sensor connector bridging signal to ground
How it failed
You'll notice: The engine is hard to start in cold weather and idle regulation gets worse.
Shorted lowRead from FMI 4: voltage below normal or shorted low
The signal sits at or near zero volts - less than a working sensor can send.
- Meter test
- Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.
- Good result
- Open circuit (OL) to ground. A low reading means chafed insulation touching metal.
When to stop
Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Coolant level and coolant temperature sensors
1 other code on this part is also shorted low (MID 128 PID 111 FMI 4). When they show together, start at the wiring and connector they share.
- MID 128 PID 110 FMI 0Engine coolant temperature critically highReal conditionStop now
- MID 128 PID 110 FMI 2Engine coolant temperature signal erraticErratic or implausibleCheck soon
- MID 128 PID 110 FMI 4Engine coolant temperature sensor signal low or shorted to groundShorted lowCheck soon
- MID 128 PID 110 FMI 5Engine coolant temperature sensor circuit openOpen circuitCheck soon
- MID 128 PID 110 FMI 16Engine coolant temperature moderately highReal conditionCheck soon
- MID 128 PID 111 FMI 1Engine coolant level critically lowReal conditionStop now
- MID 128 PID 111 FMI 3Coolant level sensor circuit shorted to positiveShorted highCheck soon
- MID 128 PID 111 FMI 4Coolant level sensor circuit shorted to groundShorted lowCheck soon
- MID 128 PID 111 FMI 5Coolant level sensor circuit openOpen circuitCheck soon
Other Volvo/Mack codes: MID 128 engine ECU - sensors and levels
- MID 128 SID 33 FMI 3Fan clutch output shorted high - fan runs full speed
- MID 128 SID 33 FMI 4Fan clutch output shorted low
- MID 128 SID 33 FMI 5Fan clutch output circuit open
- MID 128 PID 98 FMI 1Engine oil level critically low
- MID 128 PID 98 FMI 4Engine oil level sensor shorted to ground
- MID 128 PID 98 FMI 5Engine oil level sensor circuit open
Related on Equipments Finder
Source
This source lists MID 128 PID 110 FMI 4 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Mack MP7/MP8/MP10 engines (CHU, CXU, GU, TD) with the 2010-and-later MID 128 engine ECU; the same MID 128 numbers appear on Volvo D11/D13 engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
