Volvo/Mack · MID 128 engine ECU - sensors and levels
Volvo/Mack Fault Code MID 128 PID 110 FMI 0
Engine coolant temperature critically high
What does Volvo/Mack code MID 128 PID 110 FMI 0 mean?
Coolant temperature reached the critical limit and the ECM is protecting the engine. This is a genuine overheat reading, so the cause is in the cooling system, not the sensor. Urgency: stop now - shut down and fix before working on. Check first: stop the engine and let it cool before opening anything; check coolant level and look for external leaks.
- MID 128
- Which control unit reports it
- PID 110
- Parameter at fault
- FMI 0
- Data above normal, most severe
Can I keep running with it?
Stop now
Shut down and fix before working on. Running on risks damage or the machine locks out.
What should I check first?
Stop the engine and let it cool before opening anything; check coolant level and look for external leaks
Then 4 more checksWhere to read it
Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.
Checks
0 of 5 done
Causes
- Coolant level low from a leak or a failed cap
- Thermostat stuck closed or only partly opening
- Fan not engaging, or the fan clutch/drive not responding to the ECM
- Radiator or charge air cooler blocked with debris or scale
1 more causeFewer causes
- Coolant pump worn so flow is low at high load
How it failed
You'll notice: Red stop lamp lights, the engine derates and the temperature gauge climbs toward the top.
Real conditionRead from FMI 0: data above normal, most severe
The sensor reading is valid but outside the allowed range - the problem may be real.
- Meter test
- Check the real value with a separate gauge or thermometer before blaming the sensor.
- Good result
- If the gauge agrees with the display, fix the machine, not the sensor.
When to stop
Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.
Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.
Same part, other failures: Coolant level and coolant temperature sensors
2 other codes on this part are also real condition (MID 128 PID 110 FMI 16, MID 128 PID 111 FMI 1). When they show together, start at the wiring and connector they share.
- MID 128 PID 110 FMI 0Engine coolant temperature critically highReal conditionStop now
- MID 128 PID 110 FMI 2Engine coolant temperature signal erraticErratic or implausibleCheck soon
- MID 128 PID 110 FMI 4Engine coolant temperature sensor signal low or shorted to groundShorted lowCheck soon
- MID 128 PID 110 FMI 5Engine coolant temperature sensor circuit openOpen circuitCheck soon
- MID 128 PID 110 FMI 16Engine coolant temperature moderately highReal conditionCheck soon
- MID 128 PID 111 FMI 1Engine coolant level critically lowReal conditionStop now
- MID 128 PID 111 FMI 3Coolant level sensor circuit shorted to positiveShorted highCheck soon
- MID 128 PID 111 FMI 4Coolant level sensor circuit shorted to groundShorted lowCheck soon
- MID 128 PID 111 FMI 5Coolant level sensor circuit openOpen circuitCheck soon
Other Volvo/Mack codes: MID 128 engine ECU - sensors and levels
- MID 128 SID 33 FMI 3Fan clutch output shorted high - fan runs full speed
- MID 128 SID 33 FMI 4Fan clutch output shorted low
- MID 128 SID 33 FMI 5Fan clutch output circuit open
- MID 128 PID 98 FMI 1Engine oil level critically low
- MID 128 PID 98 FMI 4Engine oil level sensor shorted to ground
- MID 128 PID 98 FMI 5Engine oil level sensor circuit open
Related on Equipments Finder
Source
This source lists MID 128 PID 110 FMI 0 and its meaning. The guidance on this page is general, not taken from it.
The source covers: Mack MP7/MP8/MP10 engines (CHU, CXU, GU, TD) with the 2010-and-later MID 128 engine ECU; the same MID 128 numbers appear on Volvo D11/D13 engines.
Checks, causes, the drawing and the meter test are general workshop guidance, not the maker's procedure. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.
Machine down?
Get a replacement machine or a technician - suppliers in the UAE contact you.
