EF Logo

Volvo/Mack · MID 128 engine ECU - sensors and levels

Volvo/Mack Fan clutch control fault codes

The engine ECU drives the viscous or electromagnetic fan clutch with an output, so the fan only engages when the engine needs cooling. These codes are about that output circuit, not the cooling itself.

FaultCheckMID 128SID 33FMI 3Volvo/Mack · Fan clutch output shorted high
Plug the service tool in hereDiagnosticport, 9-pin

Where to read it

Connect the Premium Tech Tool or a J1939/J1587 scan tool to the diagnostic socket and read the codes for every module, not only the engine.

What do these codes mean?

Volvo/Mack codes MID 128 SID 33 FMI 3, MID 128 SID 33 FMI 4 and MID 128 SID 33 FMI 5 are all about the fan clutch control. None needs an immediate stop. Start with this check: unplug the clutch connector and check that the fan changes behaviour, which proves the circuit rather than the clutch.

How urgent are they?

None of the 3 codes here means stop now; all 3 can wait until the shift ends, but find the cause before the next one.

  • Check soon3

What should I check first?

Unplug the clutch connector and check that the fan changes behaviour, which proves the circuit rather than the clutch

Shared checks

Stop nowshut down and fix before working onCheck soonfind the cause before the next shiftInfonothing is failing yet

  • Volvo/Mack MID 128 SID 33 FMI 3Fan clutch output shorted high - Fan runs full speed

    The engine fan clutch driver is shorted to positive.· Shorted high
    Check soon

    Causes

    • Short to positive in the cooling fan control circuit
    • Faulty cooling fan actuator
    • Damaged harness or connector at the fan actuator

    Checks

    1. 1Watch fan speed in the scan tool; it should vary with temperature
    2. 2Unplug the fan actuator and see if the fan still runs hard
    3. 3Check the control wire for a short to a supply wire
    4. 4Inspect the actuator connector for burned or melted pins
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug the sensor and the controller. Measure resistance from the signal wire to the supply wire and to battery positive.

    Good: Open circuit (OL) between them. Any low reading is the short.

  • Volvo/Mack MID 128 SID 33 FMI 4Fan clutch output shorted low

    The fan clutch driver is shorted to ground.· Shorted low
    Check soon

    Causes

    • Short to ground in the cooling fan control circuit
    • Faulty fan actuator
    • Damaged harness or connector

    Checks

    1. 1Check coolant temperature while the engine works hard to see if the fan engages
    2. 2Unplug the actuator and check the control wire for a short to ground
    3. 3Inspect the harness and connector for damage for damage, corrosion or looseness
    4. 4Replace the fan actuator if the harness is good
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure resistance from the signal wire to ground and to the machine frame.

    Good: Open circuit (OL) to ground. A low reading means chafed insulation touching metal.

  • Volvo/Mack MID 128 SID 33 FMI 5Fan clutch output circuit open

    The fan clutch circuit is open.· Open circuit
    Check soon

    Causes

    • Open fan actuator control wire
    • Faulty fan actuator
    • Connector fault

    Checks

    1. 1Check the fan actuator connector for corrosion and loose pins
    2. 2Test continuity of the control wire to the ECM
    3. 3Check the actuator coil resistance
    4. 4Replace the actuator if the wiring is good and confirm the code does not return
    ControllerPartSupplySignalGround
    Typical three-wire sensor or two-wire coil. Your wiring diagram has the real pins.

    Meter test

    Key off, unplug both ends. Measure each wire end to end, then the part itself across its pins.

    Good: Near 0 Ω on each wire. The part reads its listed resistance, not OL.

Shared checks

Checks, in order

  1. 1Unplug the clutch connector and check that the fan changes behaviour, which proves the circuit rather than the clutch
  2. 2Measure the clutch coil resistance and compare with the service data
  3. 3Inspect the harness along the fan shroud for rubbing and heat damage
  4. 4Check for a sticking fan hub by hand with the engine off and cold

Causes

  • Fan clutch solenoid or valve failed internally
  • Short to ground or to battery in the fan clutch wire
  • Open circuit or pushed-out pin in the connector at the clutch

When to stop

You'll notice: The fan runs at full speed all the time and is noisy, or it never engages and the engine runs hot in traffic or on a hill.

Tilt, load and interlock cutouts are what keep a lift or telehandler from tipping. Never bypass or bridge one to keep working; get the fault found before anyone goes up or lifts again.

Each code above shows its own urgency. Call a technician if the checks above do not find the cause, if the code returns after clearing, or if the fix needs a service tool, a calibration or a software update.

Sources

Codes and meanings come from the sources above; short titles shorten the standard J1939 wording. Failure types, checks, meter tests and drawings are general workshop guidance, not the maker's. Codes can differ by serial number and software - confirm with the service manual or your dealer before replacing parts.

Machine down?

Get a replacement machine or a technician - suppliers in the UAE contact you.

Post a request
EquipmentsFinder

Need equipment? Have equipment?

Buyers post one request and get quotes from suppliers. Suppliers list free and reach active demand.